vacon 100 installation manual - VEM motors Finland Oy

More documents

Recommendations

Info

Power cabling vacon • 264.1 UL standards on cablingTo meet the UL (Underwriters Laboratories) regulations, use a UL-approved copper cable witha minimum heat-resistance of +60/75°C. Use Class 1 wire only.The units are suitable for use on a circuit capable of delivering not more than 100,000 rms symmetricalamperes, 600V maximum.4.1.1 Cable dimensioning and selectionTable 15 shows the minimum dimensions of the Cu/Al-cables and the corresponding fuse sizes.Recommended fuse types are gG/gL.These instructions apply only to cases with one motor and one cable connection from the ACdrive to the motor. In any other case, ask the factory for more information.24-hour support +358 (0)201 212 575 • Email: vacon@vacon.com4
vacon • 27Power cabling4.1.1.1 Cable and fuse sizes, frames MR4 to MR6The recommended fuse types are gG/gL (IEC 60269-1) or class T (UL & CSA). The fuse voltagerating should be selected according to the supply network. The final selection should be madeaccording to local regulations, cable installation conditions and cable specification. Bigger fusesthan what is recommended below shall not be used.Check that the fuse operating time is less than 0.4 seconds. Operating time depends on usedfuse type and impedance of the supply circuit. Consult the factory about faster fuses. Vacon offersrecommendations also for high speed J (UL & CSA ), aR (UL recognized, IEC 60269-4) andgS (IEC 60269-4) fuse ranges.FrameMR4MR5MR6Type0003 2—0004 20003 4—0004 40006 2—0008 20005 4—0008 40011 2—0012 20009 4—0012 40018 20016 40024 20023 40031 20031 4I L[A]3.7—4.83.4—4.86.6—8.05.6—8.0Fuse(gG/gL)[A]Mains andmotor cableCu [mm 2 ]6 3*1.5+1.510 3*1.5+1.5Terminal cable sizeMainterminal[mm 2 ]1—6 solid1—4 stranded 1—61—6 solid1—4 stranded 1—611.0—12.59.6—12.0 16 3*2.5+2.5 1—6 solid1—4 stranded 1—618.016.024.023.031.031.020 3*6+6 1—10 Cu 1—1025 3*6+6 1—10 Cu 1—1032 3*10+10 1—10 Cu 1—10Earthterminal[mm 2 ]0038 4 38.0 40 3*10+10 2.5—50 Cu/Al 2.5—350048 20046 40062 20061 448.046.062.061.050633*16+16 (Cu)3*25+16 (Al)3*25+16 (Cu)3*35+10 (Al)2.5—50 Cu/Al 2.5—352.5—50 Cu/Al 2.5—35Table 15. Cable and fuse sizes for Vacon 100 (MR4 to MR6)The cable dimensioning is based on the criteria of the International Standard IEC60364-5-52:Cablesmust be PVC-isolated; Max ambient temperature +30°C, max temperature of cable surface +70°C; Useonly cables with concentric copper shield; Max number of parallel cables is 9.When using cables in parallel, NOTE HOWEVER that the requirements of both the cross-sectional areaand the max number of cables must be observed.For important information on the requirements of the earthing conductor, see chapter Earthing andearth fault protection of the standard.For the correction factors for each temperature, see International Standard IEC60364-5-52.4Tel. +358 (0) 201 2121 • Fax +358 (0)201 212 205
Page 1 and 2: vacon 100ac drivesinstallation manu
Page 3 and 4: vacon • 16.3.3 Frame MR9.........
Page 5 and 6: vacon • 3EC DECLARATION OF CONFOR
Page 7 and 8: vacon • 5Safety1.2 WarningsVacon
Page 9 and 10: vacon • 7SafetyDo not perform any
Page 11 and 12: vacon • 9Receipt of delivery2.1 T
Page 13 and 14: vacon • 11Receipt of delivery2.3
Page 15: vacon • 13Receipt of delivery2.3.
Page 19: vacon • 17MountingFigure 9. Vacon
Page 22 and 23: Mounting vacon • 203.1.2.2 Flange
Page 24 and 25: Mounting vacon • 22Note that if s
Page 26 and 27: Power cabling vacon • 244. POWER
Page 30 and 31: Power cabling vacon • 284.1.1.2 C
Page 32 and 33: Power cabling vacon • 304.1.1.4 C
Page 34 and 35: Power cabling vacon • 32Frame A1
Page 36 and 37: Power cabling vacon • 345• Inse
Page 38 and 39: Power cabling vacon • 367Connect
Page 40 and 41: Power cabling vacon • 384.3.2 Fra
Page 42 and 43: Power cabling vacon • 40M4 x 81 2
Page 44 and 45: Power cabling vacon • 427Cut the
Page 46 and 47: Power cabling vacon • 44Connector
Page 48 and 49: Power cabling vacon • 46M4x10Figu
Page 50 and 51: Control unit vacon • 485. CONTROL
Page 52 and 53: Control unit vacon • 505.1.2 Cont
Page 54 and 55: Control unit vacon • 525.1.2.1 Se
Page 56 and 57: Control unit vacon • 54max. 40 mm
Page 58 and 59: Control unit vacon • 56Strip abou
Page 60 and 61: Control unit vacon • 58Unless alr
Page 62 and 63: Control unit vacon • 605.4 Galvan
Page 64 and 65: Commissioning vacon • 626. COMMIS
Page 66 and 67: Commissioning vacon • 646.2.1 Cab
Page 68 and 69: Commissioning vacon • 666.3.2 Fra
Page 70 and 71: Commissioning vacon • 682Further
Page 72 and 73: Commissioning vacon • 7024-hour s
Page 74 and 75: Technical data vacon • 727.1.2 Ma
Page 76 and 77: Technical data vacon • 747.2 Vaco
Page 78 and 79:
Technical data vacon • 767.2.1 Te
Page 80:
Find your nearest Vacon officeon th
show all

vacon 100 installation manual - VEM motors Finland Oy

Create successful ePaper yourself

Delete template?

Save as template?