vacon 100 installation manual - VEM motors Finland Oy

More documents

Recommendations

Info

Control unit vacon • 54max. 40 mmFigure 50.Ethernetcable2Protection class IP21: Cut free the opening on the AC drive cover for the Ethernetcable.Protection class IP54: Cut the rubber grommets open to slide the cablesthrough. Should the grommets fold in while inserting the cable, just draw thecable back a bit to straighten the grommets up. Do not cut the grommet openingswider than what is necessary for the cables you are using.IMPORTANT: To meet the requirements of the enclosure class IP54, the connectionbetween the grommet and the cable must be tight. Therefore, lead the firstbit of the cable out of the grommet straight before letting it bend. If this is notpossible, the tightness of the connection must be ensured with insulation tape or acable tie.IP54IP21Figure 51.24-hour support +358 (0)201 212 575 • Email: vacon@vacon.com5
vacon • 55Control unit3Remount the AC drive cover. NOTE: When planning the cable runs, remember tokeep the distance between the Ethernet cable and the motor cable at a minimumof 30 cm.EthernetcableIP21IP54Figure 52.For more detailed information, see the user’s manual of the fieldbus you are using.5.2.2 Prepare for use through RS4855.2.2.1 RS485 cable dataConnector 2.5 mm 2Cable typeCable lengthSTP (Shielded Twisted Pair), type Belden9841 or similarDepends on the used fieldbus. Seerespective bus manual.Table 28. RS485 cable data5Tel. +358 (0) 201 2121 • Fax +358 (0)201 212 205
Page 1 and 2:
vacon 100ac drivesinstallation manu
Page 3 and 4:
vacon • 16.3.3 Frame MR9.........
Page 5 and 6: vacon • 3EC DECLARATION OF CONFOR
Page 7 and 8: vacon • 5Safety1.2 WarningsVacon
Page 9 and 10: vacon • 7SafetyDo not perform any
Page 11 and 12: vacon • 9Receipt of delivery2.1 T
Page 13 and 14: vacon • 11Receipt of delivery2.3
Page 15: vacon • 13Receipt of delivery2.3.
Page 19: vacon • 17MountingFigure 9. Vacon
Page 22 and 23: Mounting vacon • 203.1.2.2 Flange
Page 24 and 25: Mounting vacon • 22Note that if s
Page 26 and 27: Power cabling vacon • 244. POWER
Page 28 and 29: Power cabling vacon • 264.1 UL st
Page 30 and 31: Power cabling vacon • 284.1.1.2 C
Page 32 and 33: Power cabling vacon • 304.1.1.4 C
Page 34 and 35: Power cabling vacon • 32Frame A1
Page 36 and 37: Power cabling vacon • 345• Inse
Page 38 and 39: Power cabling vacon • 367Connect
Page 40 and 41: Power cabling vacon • 384.3.2 Fra
Page 42 and 43: Power cabling vacon • 40M4 x 81 2
Page 44 and 45: Power cabling vacon • 427Cut the
Page 46 and 47: Power cabling vacon • 44Connector
Page 48 and 49: Power cabling vacon • 46M4x10Figu
Page 50 and 51: Control unit vacon • 485. CONTROL
Page 52 and 53: Control unit vacon • 505.1.2 Cont
Page 54 and 55: Control unit vacon • 525.1.2.1 Se
Page 58 and 59: Control unit vacon • 56Strip abou
Page 60 and 61: Control unit vacon • 58Unless alr
Page 62 and 63: Control unit vacon • 605.4 Galvan
Page 64 and 65: Commissioning vacon • 626. COMMIS
Page 66 and 67: Commissioning vacon • 646.2.1 Cab
Page 68 and 69: Commissioning vacon • 666.3.2 Fra
Page 70 and 71: Commissioning vacon • 682Further
Page 72 and 73: Commissioning vacon • 7024-hour s
Page 74 and 75: Technical data vacon • 727.1.2 Ma
Page 76 and 77: Technical data vacon • 747.2 Vaco
Page 78 and 79: Technical data vacon • 767.2.1 Te
Page 80: Find your nearest Vacon officeon th
show all

vacon 100 installation manual - VEM motors Finland Oy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?