vacon 100 installation manual - VEM motors Finland Oy

More documents

Recommendations

Info

Power cabling vacon • 367Connect the stripped cables (see Figure 19 and Table 19) as shown in Figure 26.• Expose the shield of all three cables in order to make a 360-degree connectionwith the cable clamp (1).• Connect the (phase) conductors of the supply, brake and motor cables intotheir respective terminals (2).• Form the rest of the cable shield of all three cables into “pigtails” andmake a grounding connection with a clamp as shown in Figure 26 (3).Make the pigtails just long enough to reach and be fixed to the terminal -not longer.L1L2L3R+ R- U V W3231Figure 26.Tightening torques of cable terminals:FrameMR4MR5MR6MR7Type0003 2—0012 20003 4—0012 40018 2—0031 20016 4—0031 40048 2—0062 20038 4—0061 40075 2—0105 20072 4—0105 4 8/15*Tightening torque[Nm]/[lb-in.]Power and motorterminalsTightening torque[Nm]/[lb-in.]EMC groundingclampsTable 20. Tightening torques of terminalsTightening torque,[Nm]/[lb-in.]Grounding terminals[Nm] lb-in. [Nm] lb-in. [Nm] lb-in.0.5—0.6 4.5—5.3 1.5 13.3 2.0 17.71.2—1.5 10.6—13.3 1.5 13.3 2.0 17.710 88.5 1.5 13.3 2.0 17.7*. Cable clamping (e.g. Ouneva Pressure Terminal Connector)70.8/132.8* 1.5 13.3 8/15* 70.8/132.8*24-hour support +358 (0)201 212 575 • Email: vacon@vacon.com4
vacon • 37Power cabling8Check the connection of the earth cable to the motor and the AC drive terminalsmarked with .NOTE: Two protective conductors are required according to standard EN61800-5-1. See Figure 27 and chapter Earthing and earth fault protection. Use an M5size screw and tighten it to 2.0 Nm (17.7 lb-in.).= M5; 2NmFigure 27. Additional protective earthing connector9Re-mount the cable protection plate (Figure 28) and the cover of the AC drive.Figure 28. Re-mounting of cover components4Tel. +358 (0) 201 2121 • Fax +358 (0)201 212 205
Page 1 and 2: vacon 100ac drivesinstallation manu
Page 3 and 4: vacon • 16.3.3 Frame MR9.........
Page 5 and 6: vacon • 3EC DECLARATION OF CONFOR
Page 7 and 8: vacon • 5Safety1.2 WarningsVacon
Page 9 and 10: vacon • 7SafetyDo not perform any
Page 11 and 12: vacon • 9Receipt of delivery2.1 T
Page 13 and 14: vacon • 11Receipt of delivery2.3
Page 15: vacon • 13Receipt of delivery2.3.
Page 19: vacon • 17MountingFigure 9. Vacon
Page 22 and 23: Mounting vacon • 203.1.2.2 Flange
Page 24 and 25: Mounting vacon • 22Note that if s
Page 26 and 27: Power cabling vacon • 244. POWER
Page 28 and 29: Power cabling vacon • 264.1 UL st
Page 30 and 31: Power cabling vacon • 284.1.1.2 C
Page 32 and 33: Power cabling vacon • 304.1.1.4 C
Page 34 and 35: Power cabling vacon • 32Frame A1
Page 36 and 37: Power cabling vacon • 345• Inse
Page 40 and 41: Power cabling vacon • 384.3.2 Fra
Page 42 and 43: Power cabling vacon • 40M4 x 81 2
Page 44 and 45: Power cabling vacon • 427Cut the
Page 46 and 47: Power cabling vacon • 44Connector
Page 48 and 49: Power cabling vacon • 46M4x10Figu
Page 50 and 51: Control unit vacon • 485. CONTROL
Page 52 and 53: Control unit vacon • 505.1.2 Cont
Page 54 and 55: Control unit vacon • 525.1.2.1 Se
Page 56 and 57: Control unit vacon • 54max. 40 mm
Page 58 and 59: Control unit vacon • 56Strip abou
Page 60 and 61: Control unit vacon • 58Unless alr
Page 62 and 63: Control unit vacon • 605.4 Galvan
Page 64 and 65: Commissioning vacon • 626. COMMIS
Page 66 and 67: Commissioning vacon • 646.2.1 Cab
Page 68 and 69: Commissioning vacon • 666.3.2 Fra
Page 70 and 71: Commissioning vacon • 682Further
Page 72 and 73: Commissioning vacon • 7024-hour s
Page 74 and 75: Technical data vacon • 727.1.2 Ma
Page 76 and 77: Technical data vacon • 747.2 Vaco
Page 78 and 79: Technical data vacon • 767.2.1 Te
Page 80: Find your nearest Vacon officeon th

vacon 100 installation manual - VEM motors Finland Oy

Create successful ePaper yourself

Delete template?

Save as template?