Installation and Operation Manual For Hunter Ceiling ... - Hunter Fan

More documents

Recommendations

Info

®STEP 1 - GETTING READYGATHERING THE TOOLSYou will need the following tools forinstalling the fan:• Electric drill with 9/64" bit• Standard screwdriver• Phillips-head screwdriver• Wrench or pliersOPTIONAL ACCESSORIESConsider using Hunter’s optional accessories,including a wall-mountedor remote speed control. To install anduse the accessories, follow the instructionsincluded with each product.For quiet and optimum performanceof your Hunter fan, use only Hunterspeed controls.PREPARING THE FAN SITEThe location of a ceiling fan and howthe fan is attached to the buildingstructure are essential for reliableoperation, maximum efficiency, andenergy savings. For this reason, wehave included a separate booklet —“Guide to Choosing and Preparinga Ceiling Fan Site” — to help youselect the best location for your fan.The booklet also provides informationto ensure your fan support andelectric outlet box meet UL-approvedsafety codes for ceiling fans.The instructions in this installationmanual assume that you have used“Guide to Choosing and Preparinga Ceiling Fan Site” to pick the fanlocation and make certain the properfan support and outlet box are installed.CHECKING YOUR FAN PARTSCarefully unpack your fan to avoiddamage to the fan parts. Check forany shipping damage to the motoror fan blades. If one of the fan bladeswas damaged in shipment, return allthe blades for replacement.Hint: If you are installing more thanone fan, keep the fan bladesin sets, as they were shipped.The fan includes a separate diagramof the screws and other small partsneeded for the fan. Keep this diagramhandy for identifying parts duringinstallation; the diagram indicatesthe step in which each part is used.If any parts are missing or damaged,contact your Hunter dealer or callHunter Parts Department at901-248-2222.641524-01 9-5-2001
®INSTALLER’S CHOICE®This patented 3-position mountingsystem provides you maximum installationflexibility and ease. You caninstall your Hunter fan in one of threeways. The steps in this manual includespecific instructions for the fanmounting method of your choice. Fora ceiling 8 feet or higher, standardmounting is recommended.Flush Mounting (Figure 1a) fitsclose to the ceiling, for low ceilingsless than 8 feet high.Standard Mounting (Figure 1b)hangs from the ceiling by a connectorpipe (included), for ceilings 8 feetor higher. For ceilings higher thaneight feet, you can purchase Hunterextension rods. All Hunter fans usesturdy 3/4" diameter pipe to assurestability and wobble-free performance.Angle Mounting (Figure 1c) hangsfrom a vaulted or angled ceiling.34° MaxPitch12810"12"Figure 1a - Flush MountingFigure 1b - Standard MountingFigure 1c - Angle Mounting41524-01 9-5-20017
Page 1 and 2: ®®SINCE 1886Installation and Oper
Page 3 and 4: ®CONGRATULATIONS!Your new Hunter c
Page 5: ®IMPORTANT INFORMATIONCAUTIONS•
Page 9 and 10: ®5. Place a flat washer on each of
Page 12 and 13: ®STEP 4 - ASSEMBLING THE FANUse th
Page 14 and 15: ®STEP 5 - HANGING THE FAN1. Discon
Page 16 and 17: ®Wall Switch Wire ForSeparate Cont
Page 18 and 19: ®STEP 8 - ASSEMBLING FAN BLADESHun
Page 20 and 21: ®STEP 9 - ATTACHING THE SWITCH HOU
Page 22 and 23: ®If your fan has a lower switch ho
Page 24 and 25: ®INSTALLING INCLUDED SINGLE-GLOBE
Page 26 and 27: ®AURORA AND TIFFANY LIGHTFIXTUREST
Page 28 and 29: ®OPERATING YOUR HUNTER FAN AND REM
Page 30 and 31: ®TROUBLESHOOTINGPROBLEM PROBABLE C

Installation and Operation Manual For Hunter Ceiling ... - Hunter Fan

Create successful ePaper yourself

Delete template?

Save as template?