Countertop Cooking Equipment - Greenfield World Trade

vollrathco.comSteam Table Pans and AccessoriesSuper Pan 3 ® withNon-Stick Interior 300 series stainless steel Dramatic black interior enhances both coldand hot food presentations Triple bonded layer coating is the finest available Cook, serve and display in the same pan Interior surface is stain resistant Temperature tolerance of -20˚ to 450˚ F (-28˚ to 230˚ C) Dishwasher safe Not for use with metal utensilsPAN SIZE ITEM DEPTH: IN (MM) CAPACITY: QT. (L) CASE LOT1/1 90017 1 1 ⁄2 (40) 5.7 (5.4) 690027 2 1 ⁄2 (65) 9 (8.5) 690047 4 (100) 14.2 (13.4) 61/2 90217 1 1 ⁄2 (40) 2.6 (2.4) 690227 2 1 ⁄2 (65) 4 (3.8) 690247 4 (100) 6.3 (6) 690047PAN SIZE ITEM DEPTH: IN (MM) CAPACITY: QT. (L) CASE LOT2/4 90527 2 1 ⁄2 (65) 3.9 (3.7) 690547 4 (100) 6 (5.7) 31/3 90327 2 1 ⁄2 (65) 2.5 (2.4) 690347 4 (100) 3.9 (3.7) 690367 6 (150) 5.8 (5.5) 61/6 90627 2 1 ⁄2 (65) 1.1 (1.1) 690647 4 (100) 1.7 (1.6) 690667 6 (150) 2.4 (2.3) 6Super Pan 3 ® Cook-Chill Cover Stainless steel Specially designed for usein the Cook-Chill process Provides rapid, uniformchilling and rethermalizationPAN SIZE ITEM CASE LOT1/1 95100 121/2 95200 121/3 95300 121/6 95600 1295100Super Pan 3 ®Flexible Pan Lids Low-density polyethylene Translucent lids allow stackingfor easy storage Sanitary and easy to clean Non-staining and dish-washer safe Safe to use in temperatures rangingfrom -20˚F to 190˚F (-28˚C to 88˚C) Ideal for cold food storagePAN SIZE ITEM CASE LOT1/1 52430 6Note: For use with Full Size Super Shapes Steam Table Pans, see page 6-3 & 6-4Flange and Opening Sizes forSuper Pan 3 ® Steam Table Pans“A”FLANGEOPENINGPAN SIZE “A”: IN (CM) “B”: IN (CM) LENGTH: IN (CM) WIDTH: IN (CM)Full 20 7 ⁄8 (53) 12 3 ⁄4 (32.4) 19 7 ⁄8 (50.5) 11 3 ⁄4 (29.8)Two-Thirds 13 7 ⁄8 (35) 12 3 ⁄4 (32.4) 12 7 ⁄8 (32.7) 11 3 ⁄4 ( 29.8)Half 12 3 ⁄4 (32.4) 10 3 ⁄8 (26.4) 11 7 ⁄8 (30.2) 9 1 ⁄2 (24.1)Half-Long 20 13 ⁄16 (52.9) 6 5 ⁄16 (16) 19 7 ⁄8 ( 50.5) 5 5 ⁄16 (13.5)Third 12 3 ⁄4 (32.4) 6 7 ⁄8 (17.5) 12 1 ⁄8 (30.8) 6 3 ⁄16 (15.7)Fourth 10 3 ⁄8 (26.4) 6 5 ⁄16 (16) 9 1 ⁄2 (24.1) 5 7 ⁄16 (13.8)Sixth 6 7 ⁄8 (17.5) 6 5 ⁄16 (16) 6 (15.2) 5 7 ⁄16 (13.8)Ninth 6 15 ⁄16 (17.6) 4 1 ⁄4 (10.8) 6 (15.2) 3 5 ⁄16 (8.4)“B”OPENINGLENGTHOPENINGWIDTHTolerances on opening dimensions are + 1 ⁄16", -0"; Flange dimensions (“A” and “B”) are ± 1 ⁄32"; Note: Corner should be 1 ⁄4" to 7 ⁄8" radius6-18