EMPIRE - White Mountain Hearth

More documents

Recommendations

Info

PARTS VIEW311611852491312101415161711VFD26F(M,P)(2,3)111071819VFD26F(M,P)7414523262142444322 202927 285 PIECE LOG ASSEMBLYTHERMOSTATIC VALVEASSEMBLY23263423242522 20 21MILLIVOLT VALVEASSEMBLY2629302423253122332021303532INTERMITTENT PILOT& VALVEASSEMBLY36373839Page 3630816-1-0912
FBBX BLOWER KIT EXTENSION INSTALLATION INSTRUCTIONSFor Unvented Gas Fireplace Model VFD26F(M,P)2, VFD26F(M,P)3Disregard FBB4 Blower Installation Instructions. Follow the installationinstructions with your FBBX blower extension kit or theVFD26 Instruction Manual.Attention: If installed, do not damage gas inlet supply line whenblower assembly is inserted into fireplace. Remove the gas inletsupply line.1. Remove blower parts from the FBB4 kit and the parts from theFBBX kit.2. Remove fan control from wire harness in the FBB4 kit.3. Attach the fan control to the fan control bracket using the two8x1/4” screws provided.4. If installed, turn OFF gas supply to fireplace.5. If applicable, turn OFF electric supply to fireplace.6. Lower bottom louver on fireplace.7. Remove upper louver.8. Remove screen frame assembly9. If applicable, remove logs from burner assembly.10. Remove burner assembly from firebox (three screws). SeeFigure 28.11. Position blower assembly behind gas valve, align notch onback of blower assembly with center screw on fireplace backand push blower assembly against fireplace back. The bowerwheel must be centered with the back wall of the fireplace.Place blower assembly against the back wall. The magnetson the back and bottom of blower assembly will sufficientlyhold blower assembly in place.12. Position speed control to the right of gas valve. Attach speedcontrol to bottom of fireplace. The magnets on the bottom ofspeed control will sufficiently hold the speed control in place.13. Attach fan control bracket to upper right side of firebox withone #10 x 1/2 hex screw provided. See Figure 27.14. Attach wire harness from the FBBX kit to the terminals on thefan control.15. Route the wire harness along the right side of the firebox.16. Connect the wire harness from the fan control to the wire harnessfrom the speed control.17. Insert power cord plug into junction box.18. Replace burner assembly in firebox with the three screws removedin Step 10.19. If applicable, replace logs onto burner assembly.20. Replace screen frame assembly.21. Install upper louver. Close bottom louver on fireplace.NOTICE: This blower is equipped with a heat activated fan controlswitch. Fan will operate when the fireplace warms up,and will turn off when the fireplace cools down.22. Installation of FBB4 and FBBX option variable speed blowerassembly is completed.Blower MotorThe blower motor does not have oiling holes. Do not attempt to oilthe blower motor.Blower WheelsThe blower wheels will collect lint and could require periodic cleaning.If the air output decreases or the noise level increases, it indicatesa dirty blower wheel. Remove fan and clean blower wheels.WARNINGUnplugging of blower accessory will not stop the heater from cycling.To turn off gas to the heater (millivolt model): push in gascontrol knob slightly and turn clockwise to OFF.” Do not force.REMOVEFAN CONTROLBRACKETSCREW HOLEFAN SWITCHSWITCHBRACKETJUNCTION BOXSPEED CONTROLFAN KITFigure 27BRICK LINERRETAINERSCREW HOLEREMOVEFigure 28REMOVE30816-1-0912 Page 37
Page 1: EMPIREComfort SystemsVent-Free Gas
Page 5 and 6: INTRODUCTIONInstructions to Install
Page 7 and 8: FIREPLACE DIMENSIONSJGCIKBADGAS LIN
Page 9 and 10: PROVISIONS FOR ADEQUATE COMBUSTION
Page 11 and 12: GAS SUPPLYCheck all local codes for
Page 13 and 14: INSTALLATION OF FIREPLACE AND MANTE
Page 15 and 16: OUTER TRIM INSTRUCTIONS1. Remove up
Page 17 and 18: PLACEMENT OF GLOWING EMBERS (ROCK W
Page 19 and 20: 10,000 BTU MILLIVOLT LIGHTING INSTR
Page 21 and 22: INTERMITTENT PILOT LIGHTING INSTRUC
Page 23 and 24: PILOT FLAME CHARACTERISTICSFigures
Page 25 and 26: MAIN BURNER AND THERMOSTAT OPERATIO
Page 27 and 28: MILLIVOLT TROUBLESHOOTINGTurn appli
Page 29 and 30: (((IP ELECTRONIC SYSTEM WIRING DIAG
Page 31 and 32: INTERMITTENT CONTROL SYSTEM TROUBLE
Page 33 and 34: JUNCTION BOX WIRING INSTALLATION IN
Page 35: PARTS LISTINDEX NO. PART NO. DESCRI
Page 39 and 40: FPP26E OPTIONAL BRICK LINER KIT INS
Page 41 and 42: WARRANTYEmpire Comfort Systems Inc.
Page 43 and 44: APPLIANCE SERVICE HISTORYDate Deale

EMPIRE - White Mountain Hearth

Create successful ePaper yourself

Delete template?

Save as template?