PDF Manual - GME

More documents

Recommendations

Info

Storing Group call Idents:Group call Idents can be stored in memory in the same way asa standard Selcall Ident.Receiving Group calls:Receiving a Group call is identical to receiving a normal Selcallexcept that the alarm sound is a LOW tone beep instead ofthe normal High tone beep. The caller’s Ident or ALPHA labelappears on the display in the usual way.RECEIVE (RX) ONLY CHANNELSThe radio includes support for up to 95 user programmableRX-Only channels with frequencies in the range 403 – 520MHz. Frequencies can be stored in five separate channelbanks labelled A to E, each containing up to 19 channels.In addition, each RX-Only channel can be assigned anindividually programmable Alpha label to help identify thatchannel when it is selected. Frequency and channel bankselections are accessed through the configuration menu.Selecting Channel BanksBefore programming or recalling channels you should ensureyou have selected the required channel bank. The 5 channelbanks can be accessed through the Configuration menu.The default channel bank is labelled RX-A.To select a Channel Bank1. Press and hold the Menu key. A high beep will be heardand the radio will enter the configuration menu.2. Briefly press the Menu key repeatedly until the RXchannelbank option is displayed.3. Rotate the Channel knob (or press or ) to selectfrom one of five channel banks RX-A through RX-E.4. When finished, press the PTT to exit the menu.Programming RX-Only channel frequenciesRX-Only channels are switched off by default. To programRX-Only channels you will need to activate the channel editorwhich will then allow access to channels 81-99 in the currentlyselected channel bank. RX-Only channels can be programmedwith frequencies in the range 403 – 520 MHz.To program RX-Only frequencies, your radio must be inNumeric mode. If your radio is in Alpha mode briefly press F -ALPHA so that ‘NUMER’ is displayed.To activate the Channel Editor1. Switch the radio off.LVL2. Press and hold the Channel knob (or PRI key) whileswitching the radio on again.3. RXALL will be displayed briefly, indicating the RX ChannelEditor has been activated.You can now rotate the Channel knob (or press or )past channel 80 to select additional channels 81-99. –OFFwillbe displayed to the left of the channel numbers indicatingthat these channels are switched off and do not containany frequencies.Selecting Frequency StepsNote: This menu option is only available when RX-Onlychannels are selected.RX-ONLY CHANNEL BANKBankChannelsA 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99B 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99C 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99D 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99E 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99PA G E 2 2 I n s t r u c t i o n m a n ua l t X 3 5 1 0 / T X 3 5 2 0 / T X 3 5 4 0
The frequency step is the space between frequencies whenthe Channel knob is rotated (or key is pressed). Thefrequency step can be set to either 12.5 kHz or 25 kHz. Thedefault is 25 kHz. You should select a frequency step thatmatches the channel allocations in the frequency band you areprogramming. When selecting 25 kHz or 12.5 kHz steps, theappropriate wideband or narrow band filter is automaticallyselected to ensure optimum performance.1. Press and hold MENU until the radio beeps.2. Briefly press MENU repeatedly until the frequency stepis displayed.4. To advance through the frequencies more quickly, brieflyLVLpress the Channel knob (or PRI key). The frequency willnow adjust in 1 MHz steps. As you approach the desiredLVLfrequency, briefly press the Channel knob (or key)PRIagain to return the original 25 kHz/12.5 kHz steps.5. Once your desired frequency is displayed, press and holdLVLthe Channel knob (orPRIkey) until the radio beeps.The frequency is now stored under your selectedchannel number.25 kHz Steps 12.5 kHz Steps3. Rotate the Channel knob left or right (or press or )to change the frequency step.4. Press the PTT to exit the menu.To program an RX-Only frequency:1. Rotate the Channel knob (or press or ) to select asuitable channel number (81-99). –OFF- will be displayedto the left of the channel number.2. Press and hold the menu key until the radio beeps. ‘–OFF-’will flash. You now have 6 seconds to begin programmingotherwise the menu will time-out.3. Rotate the Channel knob to the right (or press ) tobegin selecting your desired frequency starting at 403 MHz.Continue to rotate to the right (or press ) to increasethe frequency or to the left (or press ) to decrease thefrequency. The display will show the frequency to thenearest 10 kHz.e.g. 468.425will display as:4 6 8 4 210 kHz100 kHz1 MHz10 MHz100 MHze.g. 458.325 MHz stored under CH 906. Repeat steps 1 – 5 to program other channels.Note: The frequency tuning is live which means the radio isactually listening to the frequencies you are selecting. You canuse this feature to locate and store active frequencies whileyou are tuning.To program more than 19 channels, you will need to switch toanother channel bank. Simply press the Menu key repeatedlyuntil the RX- Channel Bank option appears then selectanother Channel Bank. Once selected, press the Menu keyrepeatedly to return to the frequency programming option andcontinue programming your preferred frequencies.To close the Channel EditorSwitch the radio Off then On again to close the channeleditor and restore normal operation. Your programmedfrequencies will now be accessible from the Channel knob(or and keys). Remember, if you have stored channelsinto different channel banks, you will need to select theappropriate channel bank to access them.Note: Under normal operation, only those channels that havebeen programmed with frequencies will be visible. Channelsthat were marked with –OFF- in the channel editor will nolonger be visible.T X 3 5 1 0 / T X 3 5 2 0 / T X 3 5 4 0 i n s t r u c t i o n m a n ua l PA G E 2 3
Page 6 and 7: LCD PANELSelcall TXSelcall RXQuiet
Page 8 and 9: Keypad Functions.general operation
Page 10 and 11: your face and speak at a normal voi
Page 12 and 13: Your radio allows you to enable or
Page 14 and 15: Default working channel in Open Sca
Page 16 and 17: 5. To see the actual sub tone inste
Page 18 and 19: Call acknowledgeIf your Selcall tra
Page 21: TIP: To ensure reliable Selcall det
Page 25 and 26: the or keys) to change the selected
Page 27 and 28: Console mountingA flush mounting DI
Page 29 and 30: Fitting the controller microphonePl
Page 31 and 32: ignition or alternator wiring. If t
Page 33 and 34: UHF CB Operating FrequenciesChannel
Page 35 and 36: standard communications WARRANTY AG

PDF Manual - GME

Create successful ePaper yourself

Delete template?

Save as template?