PDF Manual - GME

More documents

Recommendations

Info

Deleting an RX-Only channelTo delete an RX-Only channel;1. Enable the Channel Editor.2. Select the channel you wish to delete.3. Press and hold the MENU key until the radio beeps.4. Rotate the Channel knob all the way to the left (or pressrepeatedly) until –OFF– is displayed.LVL5. Press and hold the Channel knob (or PRI key) to storethe new setting.6. Switch the radio Off then On again to restorenormal operation.The deleted channel will no longer be visible.Displaying the RX-Only channel’s frequency orAlpha labelBy default the radio displays the Signal Strength meter to theleft of the channel number. You can configure the display toshow the Frequency or the Alpha name of theselected channel.Before starting, ensure the radio is in the Numeric mode (pressF then ALPHA so that ‘NUMER’ is displayed).1. Select an RX-Only channel (the following menu option isonly available when an RX-Only channel is selected).2. Press and hold MENU until the radio beeps.3. Briefly press MENU repeatedly until S-MET appears.4. Rotate the Channel knob to the right (or press ) untilALPHA is displayed.5. Press the PTT to exit the Menu.The radio will now display the channel frequency to the left ofthe channel number whenever an RX-Only channel is selected.To display the channel’s ALPHA labelBriefly press F then ALPHA. ‘ALPHA’ will appear briefly thenthe channel’s Alpha label will be displayed to the left of thechannel number. If the Alpha label is blank, then an Alphalabel has not yet been set for this channel. Follow the stepsright to enter your preferred Alpha label.Adding names to your RX-Only channelsNote: You do not need to activate the channel editor tomake changes to RX-Only channels that have alreadybeen programmed.1. Select an RX-Only channel. The channel frequency will bedisplayed to the left of the channel number.2. Press F then ALPHA to switch to Alpha mode. ‘ALPHA’ willbe displayed briefly.3. Press and hold the MENU key until the radio beeps. Thecursor will flash in the left character position.4. Rotate the Channel knob (or press or ) to select theLVLrequired character. Press the Channel knob (or key)PRIto advance to the next character position.5. When the desired name is displayed, press and hold theLVLChannel knob (or PRI key) to store the name.6. Briefly press the PTT to exit and return to normal operation.RX-Only channel frequency (458.325 MHz)RX-Only channel labelWhen viewing RX-Only channels, briefly press F then ALPHAat any time to toggle between the channel frequency and theAlpha name.Configuration menuThe configuration menu controls preset functions in the radio.To access the menu, press and hold the MENU key until a beepis heard. Selected menu options are displayed to the left of thechannel display. Briefly press the Menu key to step through theavailable menu options. Rotate the Channel knob (or pressPA G E 2 4 I n s t r u c t i o n m a n ua l t X 3 5 1 0 / T X 3 5 2 0 / T X 3 5 4 0
the or keys) to change the selected menu option.After viewing or making changes, briefly press the PTTto exit the menu (or simply wait a few seconds for themenu function to time-out).The following settings are available.Menu OptionRX Only Frequency/Alpha Label:CTCSS/DCS:Voice Scrambler:UHF CBChannelNARX-OnlyChannelFrequency, AlphaLabelCTCOF, CTC01-CTC50, DT001-DT104ENCOF, ENCONBeep Tone Level: BEEP 0 – BEEP 9RX Only FrequencyStep :NA25.0 K, 12.5 KFilter Bandwidth: WBFLT, NBFLT –Dynamic VolumeControl:Display ModeOptions:Busy Lockout:RX Only ChannelBanks:S-MET, S-LIN,BATTNADVCOF, DVCONBLKOF, BLKONS-MET, S-LIN,BATT, ALPHARX-A, RX-B, RX-C,RX-D, RX-EFrequency/Alpha label(only available on receive-only channels)Allows editing of the channel frequency or Alpha label of theselected receive-only channel.Frequency 458.325 MHz Alpha label “FIRE 1”Voice ScramblerEnables or disables the Voice Scrambler.Scrambler Encoder OffScrambler Encoder ONBeep tone levelAdjusts the volume level of the beep tones associated withkey presses.Beep level 0Beep level 9Frequency step selection(only available on receive-only channels)Sets the frequency spacing of receive-only channels to 12.5kHz or 25 kHz (default).25 kHz stepsRotate leftrotate rightCTCSS Off CTCSS Tone 50 DCS Tone 10412.5 kHz stepsNote: This option does not affect the standard 80 CBchannel spacingFilter bandwidth(only available on CB channels)Selects the receiver bandwidth filter on channels 1-40.CTCSS/DCS tone selectionEnables and selects CTCSS or DCS tones. To switch CTCSS orDCS tones off rotate the Channel knob fully to the left (orpress repeatedly) until ‘CTCOF’ is displayed.Wideband Filter selectedNarrowband Filter selectedT X 3 5 1 0 / T X 3 5 2 0 / T X 3 5 4 0 i n s t r u c t i o n m a n ua l PA G E 2 5
Page 6 and 7: LCD PANELSelcall TXSelcall RXQuiet
Page 8 and 9: Keypad Functions.general operation
Page 10 and 11: your face and speak at a normal voi
Page 12 and 13: Your radio allows you to enable or
Page 14 and 15: Default working channel in Open Sca
Page 16 and 17: 5. To see the actual sub tone inste
Page 18 and 19: Call acknowledgeIf your Selcall tra
Page 21 and 22: TIP: To ensure reliable Selcall det
Page 23: The frequency step is the space bet
Page 27 and 28: Console mountingA flush mounting DI
Page 29 and 30: Fitting the controller microphonePl
Page 31 and 32: ignition or alternator wiring. If t
Page 33 and 34: UHF CB Operating FrequenciesChannel
Page 35 and 36: standard communications WARRANTY AG

PDF Manual - GME

Create successful ePaper yourself

Delete template?

Save as template?