Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
1-5. Hi-Hat Offset<br />
This sets the value of the data sent by a foot controller connected<br />
to the HI HAT CONTROL jack on the rear panel. Set a + (plus) or<br />
– (minus) level.<br />
UT SYSTEM<br />
HH OffS= 0T= 32<br />
q w<br />
q HH OFFS (Hi-Hat Offset)<br />
When a low data value is received from the foot controller, the<br />
voice will sound sooner. So, slightly pressing the foot controller<br />
will result in the voice sounding. In the case of the hi-hat controller,<br />
delicate adjustment of the controller’s “closed” point is possible.<br />
w T (Foot Splash Detect Time)<br />
Sets the detect time for the foot splash. Large values make foot<br />
splashes easier to produce.<br />
* Values too large will result in splashes being produced under<br />
normal hi-hat use.<br />
1-6. Factory Set<br />
This function replaces all internal settings in the DTXPRESS to<br />
their factory-set condition.<br />
UT SYSTEM<br />
Factory Set<br />
The Factory Set function will replace all internal settings<br />
in the DTXPRESS to their factory-set condition.<br />
Take care so as not to loose important data.<br />
Make sure any settings and user songs you want to<br />
keep have been saved to an external device such as<br />
the <strong>Yamaha</strong> MIDI Data Filer MDF3, etc. (m[2-1.<br />
Bulk Dump] (P. 29)<br />
Procedure<br />
1. Enter the display shown above, press the [SAVE/ENT]<br />
button. The following display will appear asking for confirmation<br />
before the Factory Set operation is carried out.<br />
All data will be<br />
lost.AreYouSure?<br />
2. Once again, press the [SAVE/ENT] button to proceed<br />
with the operation.<br />
2. MIDI Group<br />
This sub-mode contains functions and settings for the MIDI and<br />
TO HOST jacks of the DTXPRESS. This group is divided into the<br />
following 10 pages.<br />
2-1. Bulk Dump ....................................................... 29<br />
2-2. Channel 10 Program Change/<br />
Channel Event Receive ................................... 30<br />
2-3. Receive Program Change/<br />
System Exclusive Messages ........................... 30<br />
2-4. Program Change Table .................................... 31<br />
2-5. MIDI Mode ....................................................... 31<br />
2-6. Device Number, Local Control ......................... 31<br />
2-7. MIDI Merge ...................................................... 31<br />
2-8. Dump Interval .................................................. 32<br />
2-9. Send Hi-Hat Control ........................................ 32<br />
2-10. Host Thru Port ................................................. 32<br />
* Please refer to the [MIDI Data Format] (P. 50) section for more<br />
information related to MIDI.<br />
2-1. Bulk Dump<br />
With the Bulk Dump operation, data stored in the ETXPRESS can<br />
be transmitted via the MIDI OUT or TO HOST jack.<br />
UT MIDI BULKDUMP<br />
Fmt= all data q<br />
Utility Mode<br />
q Fmt (Bulk Dump Format)<br />
Selects the type of data to be transmitted with the Bulk Dump<br />
operation.<br />
all data : All the data in the DTXPRESS<br />
system data : Data set in the Utility mode (except User<br />
Map).<br />
user map : User Map data.<br />
one drumkit : Data for the currently selected <strong>Drum</strong> Kit.<br />
all drumkit : All User <strong>Drum</strong> Kit Data.<br />
one trigger : Data for the currently selected Trigger Setup.<br />
all trigger : All User Trigger Setup data<br />
one song : Data for the currently selected User Song.<br />
all song : All User Song data.<br />
Procedure<br />
1. After reading the [Connecting a MIDI Device] (Basic<br />
Guide : P. 12) or the [Connecting a Computer] (Basic<br />
Guide : P. 26) section, connect the external MIDI device<br />
or computer to the MIDI OUT or TO HOST jack on the<br />
DTXPRESS. Set the HOST SELECT switch.<br />
29