Napco Gemini LCD Keypad - Microtec

More documents

Recommendations

Info

TURNING OFF THE ALARM (DISARMING) WHEN RETURNINGENTRY TIME XXXDISARM SYSTEMINVALID ENTRYTRY AGAIN**** ALARM ****02 - BACK ALARM03 - LIVING ROOMDisarming the System1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone toremind you to disarm the system before your Entry Delay time expires.2 Enter your User Code and pressJ. The red ARMED light will go out, indicating that thesystem has been disarmed.If you enter an invalid code, the keypad will beep 4 times, signifying an error. Re-enter yourcode immediately. 10 seconds before Entry Delay expires, the keypad will emit a pulsingwarning tone.Alarm Indication/Silencing an AlarmIf the red ARMED light is flashing and “ALARM” is displayed, an alarm occurred whileyou were out. Proceed with caution! If you suspect that an intruder may still be on thepremises, leave immediately and call authorities from a neighbor's phone.To silence an audible alarm:Enter your code and press J. After the system is disarmed, the window will continue todisplay “ALARM” followed by the zone(s) violated. To reset the display, note the zonesviolated, then press C.Ambush (Optional - Ambush programmed? qYES qNO) (Your Ambush Code is __ __ )The Ambush Code (optional) is a 2-digit code that is entered just prior to your Disarm Code. If an intruder forces you to disarmyour system, (a) enter your Ambush Code; (b) enter your Disarm Code; (c) pressJ.Example: If your User Code is 1234 and your Ambush Code is 99, press 9 9 1 2 34J.This will send a silent alarm to the central station. The red ARMED light will go out and the window will display “SYSTEMREADY”, as if the system were merely disarmed. There will be no indication that an alarm has been sent.10
FIRE PROTECTION(Applicable only where local ordinance permits use of this alarm control panel for fire protection.)FIREFIREFIRE ALARMFIRE TROUBLEFire-Zone AlarmIf a fire is detected, “FIRE ALARM” will be displayed and the keypad sounder will pulse.If a fire is in progress, evacuate the premises immediately! If necessary, call the FireDepartment from an outside phone.Resetting a Fire-Zone Alarm1 Press the C button to silence the keypad sounder.2 If there is no evidence of a fire, enter your User Code and pressJ to turn off the alarm Check smoke detector(s). If a smokedetector tripped, its red alarm indicator light will be on.After the alarm condition is corrected (thermostat cooled down; smoke cleared from detector; etc.), pressing C againwill reset the keypad within about 10 seconds.11
Page 1: OPERATING GUIDE for yourGEM-RP1CAe2
Page 5 and 6: 12345Window. Displays system status
Page 7: SETTING THE ALARM (ARMING) WHEN LEA
Page 12 and 13: Preparing a Fire Escape PlanEven wi
Page 15 and 16: KEYPAD FUNCTIONSThe keypad can prov
Page 17 and 18: RESETSYS TRBLY/NKEYPAD FUNCTIONSRes
Page 19 and 20: ACTIVATEPROGRAMY/NKEYPAD FUNCTIONSA
Page 21 and 22: ADVANCED FEATURESSecurity Bypass/Un
Page 23 and 24: PROGRAMMING (OPTIONAL)Reviewing a P
Page 25 and 26: PROGRAMMING (OPTIONAL)Programming t
Page 27 and 28: KEYPAD MESSAGES****ALARM****Alarm c
Page 29 and 30: GLOSSARYFollowing are brief descrip
Page 31 and 32: System Trouble: A problem (lowbatte
Page 33 and 34: SYSTEM TROUBLE ERROR CODESTroubleIn
Page 35 and 36: SYSTEM TROUBLE ERROR CODESTroubleIn
Page 37 and 38: What do I do if...TROUBLESHOOTINGI
Page 39 and 40: NOTES39

Napco Gemini LCD Keypad - Microtec

Create successful ePaper yourself

Delete template?

Save as template?