Download

More documents

Recommendations

Info

Commissioning and operationFirst commissioningWhen putting a new or overhauled engine into operation for the first time pay attention tothe “Installation instructions for MAN marine diesel engines” without fail.It is recommended that new or overhauled engines should not be operated at a loadhigher than about 75% maximum load during the first few hours of operation. Initial run-inshould be at varying speeds. After this initial run-in, the engine should be brought up tofull output gradually.Note:Use only approved fuels, lubricants etc. (see brochure “Fuels, lubricants etc.”).Otherwise the manufacturer’s warranty will become null and void.Filling with fuelCaution:Fill the tank only when the engine is switched off. Pay attention to cleanliness.Do not spill fuel.Use only approved fuels (see “Fuels, Lubricants etc.”).Filling-in of coolantFill the cooling system of the engine with a mixture of drinkable tap water and anti-freezeagent on ethylene glycole basis or anti-corrosion agent.See Publication “Fuels, Lubricants and Coolants for MAN Diesel Engines”.D Pour in coolant slowly via expansion tank, see page 57D For coolant filling quantity, see “Technical data”16
Commissioning and operationRaw water pumpDo not let raw water pump run dry.Make sure that all valves / cocks in theraw water circuit are open.If there is a risk of frost, drain the raw waterpump.Filling with engine oilCaution:Do not add so much engine oilthat the oil level rises above themax. marking on the dipstick.Overfilling will result in damage tothe engine.The engines are as a rule supplied withoutoil.Pour oil into engine via filler neck (arrow),see page 51.For the quantity required see “TechnicalData”.17
Page 3: Operating Instructions -MAN Marine
Page 6 and 7: InstructionsImportant instructions
Page 8 and 9: DeclarationDeclarationIn accordance
Page 10 and 11: Safety regulationsGeneral notesHand
Page 12 and 13: Safety regulations2. Regulations de
Page 14 and 15: Commissioning and operationEngine v
Page 18 and 19: Commissioning and operationCommissi
Page 20 and 21: Commissioning and operationOperatio
Page 22 and 23: Commissioning and operationOperatio
Page 24: Commissioning and operationRepresen
Page 27 and 28: Commissioning and operationVisual Q
Page 29 and 30: Commissioning and operationThe sele
Page 31 and 32: Commissioning and operationShip-spe
Page 33 and 34: Commissioning and operation“Gearb
Page 35 and 36: Commissioning and operationAddition
Page 37 and 38: Commissioning and operationInfinite
Page 39 and 40: Commissioning and operation2. Comma
Page 41 and 42: Commissioning and operation2nd step
Page 43 and 44: Commissioning and operationOperatin
Page 45 and 46: Commissioning and operationDisablin
Page 47 and 48: Commissioning and operationMain fus
Page 49 and 50: Commissioning and operation- In the
Page 51 and 52: Maintenance and careRefilling with
Page 53 and 54: Maintenance and careFuel systemFuel
Page 55 and 56: Maintenance and careChanging fuel f
Page 57 and 58: Maintenance and careFilling / bleed
Page 59 and 60: Maintenance and careV-beltsChecking
Page 61 and 62: Maintenance and careAlternatorThe a
Page 63 and 64: Technical dataEngine lubricationFor
Page 65 and 66: Technical dataEngine lubricationFor
Page 67 and 68:
Troubleshooting tableFaultEngine do
show all

Download

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?