GoldenEye User Manual

GOLDENEYE INSTALL GUIDE MANUAL 

GoldenEye User Manual 

- GED 100, 200, 1000, 3000 series 

- GED 2000, 4000, 2200, 4200 series 

- GED 5500 series 

Digital Video Recorder System 

Winnertec Systems Co., Ltd 

#405, 4FL, ACE Techno Tower 3, #197-48 

Kuro3-Dong Kuro-Ku, Seoul 152-053, Korea 

Tel : +82-2-839-6531 

FAX : +82-2-839-6573

NOTICE 

1 

1.1 

1.2 

2 

2.1 

2.2 

3 

3.1 

3.2 

3.3 

3.4 

3.5 

3.6 

3.7 

3.8 

4 4.1 

4.2 

4.3 

4.4 

4.5 

4.6 

5 

5.1 

6 

7 

8 

8.1 

8.2 

9 

10 

10.1 

10.2 

10.3 

10.4 

10.5 

10.6 

CONTENTS 

Introduction 

Precaution before Installation 

Warranty sheet 

Warranty Contents 

Checking List 

GOLDENEYE USER GUIDE MANUAL 

System General ------------------------------ 

System Features --------------------------- 

Main Function ----------------------- 

Monitoring Mode ----------------------------- 

Monitoring mode Explanation ------------------ 

Pan/Tilt Control Method ----------------------- 

Function Setting Methods ---------------------- 

Way of Function Converting ------------------- 

General Setting---------------------------- 

Camera setting ----------------------------- 

Motion & Display Setting ---------------------- 

Network Setting ----------------------------- 

Sensor Setting ------------------------------ 

User Setting ------------------------------- 

Save ------------------------------------ 

Searching Mode ------------------------------ 

Searching Mode Conversion & Methods --------- 

Multi searching way -------------------------- 

Searching screen Button Explanation ------------ 

Motion Searching Way------------------------ 

How to use Book Mark ----------------------- 

Data Saving Way---------------------------- 

Log Viewer ----------------------------------- 

Event Backup -------------------------------- 

Image Tool ---------------------------------- 

Backup ------------------------------------- 

Manual Backup Method ----------------------- 

Auto Backup Method ------------------------- 

Backup Viewer -------------------------------- 

GoldenEye Installation ------------------------ 

Front & Back part of the System ---------------- 

Capture Card Connection and Receiver ---------- 

Sensors & Relays Connector Pin Spec (KIT) -------- 

Back I/O B/D with Sensors & Relays (SET) --------- 

Pan/Tilt Camera Protocol --------------------- 

Sound setting for Audio ---------------------- 

1 

1 

1 

2 

2 

3 

5 

5 

6 

7 

11 

12 

13 

15 

15 

16 

16 

18 

19 

19 

22 

23 

24 

26 

29 

30 

31 

33 

36 

37 

37 

38 

39 

39 

40 

41 

Winnertec Systems Co., LTD

Products Introduction 

* Please check out the power if 110/220 Voltage. 


GED100, GED200, GED1000N, GED3000N, GED1600, GED3600, GED2000, GED4000, 

GED2200, GED4200, GED5500 are WINNERTEC SYSTEMS CO., LTD‘ s GoldenEye 

series. 

Thanks for choosing our products. This manual includes DVR system program setting 

methods, function, features & pan/tilt Control connection. 

Precaution before Installation 

* Please read carefully before you use it. 

* Basic function is same even though it is various according to model. 

1. Refer to manual before installation, put the power “ off” before connecting. 

2. Make an enough room for the line. 

3. Do not install this around the place where there is magnetic, direct light 

Heating equipment. (In use temperature 5℃~35℃) 

4. Install this onto stable place and well-ventilated place. 

5. Do not put the heavy objects on this. 

6. Do not break this product into pieces. 

* You have to get help from Winnertec systems when you need to uninstall for 

repairing. 

* Please make sure that we are not responsible for any kind of wrong treatment of 

customer to our products. 


Warranty Introduction 

Warranty Contents 

Model 

Serial no 

Purchasing place/Tel 

Date of purchase 

Warrantee period 

CUSTOMER 

NAME 

ADDRESS 

TEL 


We guarantee that we will repair and exchange defective products when there 

are any Defaults on our products under this paper. 

If our products break down within 1Year under the manual condition, We 

should repair it without any charge. (Expect under the uncontrolled condition) 

Chargeable cases as follows;. 

1. Breaking down or damage from user’ s mistakes. 

2. If you do not keep our instruction according to this manual. 

3. If you do not use recommendable power level or frequency. 

4. If it needs disassembling typed-cleaning or consuming components. 

5. If some other people repair or amend this equipment without our 

permission. 

When the warrantee period passes, small amount of charge will be added for 

repairing. 

⊙ This paper will not be reissued. 

⊙ Please confirm the contents of this when you purchase this products. 

⊙ Please show us this paper when you need to get repairing. 


Checking List 


Please check if you have all the items as follows and if you find some other material 

missing, contact the purchasing place. 

(Option : Monitor, Audio Input Cable, Network connecting Cable) 

SET Base 

� MONITOR (OPTION) 

- Resolution 1024 * 768, 60Hz 

True Color, +32bit 

� GOLDENEYE SYSTEM (Digital Video 

Recorder System) 

� Key Board, Mouse 

� Power Cable 

� User manual 

� S/W CD (Main B/D, VGA CD included) 

� Reck fixing Bracket , HDD fixing Reck(If HDD is more than two, 

there is no fixing Reck) 

� Key Board 

� Network changing cable, Serial Port Connecting Cable(In case of 

PTZ Cam: Option) 

KIT Base 

� S/W CD (DVR, RMS, DRIVERS) 

� CAPTURE OR OVERLAY BOARD 

� CAMERA CABLE 

� SENSOR CABLE 

� VIDEO INPUT CABLE 


1 System General 

1.1 System Features 

1.2 Main Function 

1 


This system makes analogue signal into digital signal and save it in HDD, then 

search those information when you need. This is what we called DVR (Digital 

Video Recorder) 

1) System Stability 

We spent more than 4 Years to make our systems stabilized. 

2) System File System 

We developed the most suitable file system and prevented disk piece in advance, 

so we maximize HDD space and minimize disk access time. 

For the security reason, we only permitted only authorized users to search our data. 

3) Excellent Screen Quality 

Saving the clean image when the event happens, so you can see the recording image 

very clearly. 

4) Convenient user interface 

For the user’s convenience, we let the users operate only with mouse clicking. 

5) Superior network function expansion 

Searching, Displaying, Transmitting are being done at the same time. 

Two – Way Audio, Network, Remote monitoring through Modem (PSTN) are our special 

features. 

[ Configuration ] 

- Maximum 16ch divided Live Video Monitoring 

- 30 ~480 fps/second recording (JPEG, MPEG4) 

- Control of recording speed & compression way 

by each camera 

- Main File System adaptation 

- RMS (LAN, PSTN, ISDN) 

- Search & Data backup (DAT, DVD, ADR, DLT, 

CDR/W) 

- Motion detection function 

- Self Control Function (Watch Dog) 

- Remote notification (Hand Phone, E-mail) 

- Voice recording 

- Multi-Level Password 

- PAN/TILT 

For more information, please go to our website. (http://www.winnertec.co.kr) 

Winnertec Systems Co.,LTD

2 Monitoring Mode 

1.1 Monitoring Mode Explanation 

Camera information display part 

(10) Camera shows the current status of camera 

Standby recording on record Not using 

Search and Control Part 

< How to use Mouse > 

2 


Information display part 

(1) Date and Time 

(2) Sensor & Alarm, RMS, Backup 

(3) Saving degree 

(Oldest Basket saving data) 

Screen control part 

(4) 1, 4, 6, 9, 10, 16 division 

(5) Maximum screen 

(6) Converting to next camera 

(7) Automatic group 

(8) PAN TILT CONTROL 

(9) Exit button 

Search conversion Log Viewer function setting Event Backup 

1) Screen conversion 

- Temporary screen clicking makes screen one division screen. 

- Division screen depends on how many screen user want to use. 

(As soon as you choose, turns out to be blue) 

- If you put auto screen conversion button, Camera group is changing continuously. 

- This is the same as click next camera (next group) 

2) Full screen 

- If you click full button, it turn out to be full screen. 

- Click right mouse button makes it turn to previous screen. 

< Pop up > 

- When you move your mouse, advice for pop up displays. 


2.2 Pan/Tilt Control Method 

1. PAN/TILT Setting Method 

3 


When you watch the video and control the view scope of camera or it can be possible to 

control focus in/out & zoom in/out. 

This is different according to Receiver (refer to Appendix Receiver) 

(1) Click setting -> Put the ID & Password, click “OK” -> select the camera in setting mode. 

(2) ‘Camera Setting’ 

... example : Pan/Tilt Receiver is Pelco D (Pelco D, 2400, NONE, 8, 1) 

-> Select No.1Camera 

-> Check in “use” on Pan/Tilt 

-> Select ‘Pelco D’ among the Receiver item. 

-> Select ID (ID is Pan/Tilt’s No) 

-> Select Speed, Port, Parity, Data Bits, stop Bits list. (2400, NONE, 8, 1) 

-> Click ‘OK’ 

-> Click ‘Save and Exit’ 

Caution during Pan/Tilt operation 

Pan/Tilt Receiver is Pelco D 

Pelco D, 2400, NONE, 8, 1 

Pan/Tilt Receiver has a various of model and protocol. Please check if there is such 

a kind of receiver. If this does not work, there might have some problem on line 

connection or new upgraded version protocol. 

ID is Pan/Tilt’s Number. 


2. How to use Pan/Tilt 

< Adding preset > 

(1) Click the preset ( ) button. 

(2) Control the P/T button to where you want to move. 

(3) Click the right button and put the ‘Add Preset’ 

(4) Put the explanation of preset. 

< Go to preset > 

(1) Click ‘Pan/Tilt’ button, and put ‘ID’ & ‘Password’ 

(2) Color turns into blue when it is being used. 

3. How to use Preset 

4 


(3) Click the icon. You can change following (left/right) icon. 

(4) You can check out all direction with Zoom In/Zoom Out button 

also. 

< Explanation on Controller > 

Camera power button/Light power button 

Zoom In/ Zoom Out button 

Focus In/ Focus Out button 

Auto Pan button 

(1) Click the preset ( )button. 

(2) Click the right button at the number, which you want, and put the ‘Go To Preset’. 


3 Function Setting Methods 

3.1 Way of Function Converting 

5 


(The shape of icon before/ after) 

(1) Click the Setup button. 

(2) Put ID & Password. 

*REF: Please make sure that nobody except 

operator changes this setting mode. 

Logging in is made only when operator put ID 

& Password. 

(3) After logging in, Setting window as left 

shows up. This is made of sixth Setting Parts 

& two Saving Parts. 

- Setting Part: General (System), Camera, 

Motion & Display, Network, Sensor & Alarm, 

and User 

- Saving Part: Save & Exit, Exit without Save 


3.2 General Setting 

(1) (2) 

(4) 

(5) (6) 

(1) Initialize : Interval and Initialization 

(3) 

6 


- Composite Monitor display interval : Composite( TV ) Monitor 

(Default: 3Sec, Converting ever 3minutes) 

- Pan/Tilt Control seeing Composite Monitor : From the composite monitor you can check 

out moving image on camera. 

- Full Screen : Set for full screen. 

- Change color on recording : It turns into red. 

- Initial screen split : Initial mode( 1,4,9,16 division ) 

(2) System Controls 

- Shutdown Time : System ending 

Ref : If power does not turn off, check CMOS setting mode. 

- Use Restarting : Restart of System 

- Disable (Ctrl+Alt+Del Key) : This is for not using Key board. 

System should be rebooting on Window2000/XP 

- Watchdog : System monitoring function (Default: 60 Sec) 

(3) Video Mode : You can check NTSC or PAL mode. 

(4) Site Location : Putting the name of Users(DVR) (ex, Seoul police station) 

(5) Event Log : Event( Motion, Sensor, Video Loss) Log (REF : Log Viewer ) 


3.3 Camera Setting 

(10) 

(3) 

(1) 

(2) 

(1) Select Camera 

You can choose if you use PTZ, CODEC type, etc. 

(2) Camera Option 

- Use: You have to check here after select the camera. 

7 


(9) 

(7) 

(4) 

(6) 

(5) 

(8) 

* Apply same value to all camera : If you want to make 

all the function same. 

(You can choose if you use PTZ, CODEC type, etc) 

< Extended camera information > 

- Camera Name: This let us know the 

location of camera at searching mode. 

- Other information will be put into RMS 


8 


- Notify E-Mail on Event 

It sends e-mail notice when event happens (Motion, Sensor, Video Loss) 

Outgoing mail Server : SMTP Server 

From : Sender’s account 

Authentication: When you need certification through e-mail server, ask mail server 

manager. 

ID/Password : Put User ID & Password. 

To : Address of receiver (about upto 10 persons possible ) 

Cc : Address of reference persons (about 10 person possible) 

Subject : Mail subject 

Content : Image will be attached when motion & sensor happens. 

- Hide View on PC Monitor : This is very good secret recording without letting anyone note. 

- Remove from external monitor rotation : . 

- Beep and show one split on event : When motion & sensor happens, is makes one 

division screen and beep sound issues. 

(3) Pan/Tilt 

Refer to 3.2 Pan/Tilt control methods. 

(4) Size & Quality Adjustment 

- JPEG/MPEG4 choice: Each camera has a different designation. 

- Resolution / Quality: Resolution - 320*240(Default) 640*240, 640*480, 

Quality - JPEG is 62%, MPEG4 is 62% advisable 

*REF : Mail server should 

be able to support POP3. 

*REF 

(5) 녹화된 이미지에 문자 보이기 

Each model has different FPS rate per mode. For example GED200, GED2000, GED4000 has 

120FPS(In 사용에 체크하고 case of NTSC), 포지션을 this is 설정(좌측 only when 위/아래, 320*240 mode. 우측 위/아래)하고, 640*480 mode has 포함사항(이름과 60~70FPS. 날 

Under 짜, 시간)을 PAL type 선택하여 320*240 주면, mode 100FPS, 검색 시에 640*480 보이게 mode 됩니다. 50~60FPS when it is recording. 

CPU, Main B/D(Chipset: Intel, Via, SIS, etc), RAM is able to affect on this rate also. 


(6) Adjust Camera Frame rate 

You can designate every camera’s frame rate. 

9 


* Caution 

Recommandation is that Maximum Averaged Frame Rate. If you want to set each different camera’s 

frame rate, it should be done within the maximum frame rate it can support. 

In case of GED2000: Total frame rate 120FPS, so allow within this scope. 

(7) Sound 

- Sound : You can choose sound availability. (Mic1~16), Card 

- MIC means availability of mike usuage with power on. 

- Card means that you are going to use make MIC part of sound card. 

(8) Holiday Setup 

This is for setting in order to designate one specific date (such as Sunday) 

* How to use 

1) Select date. 

2) Click ‘Add’. 

3) Click the date and put ‘Comment’ on list and click ‘Enter key’. 

(9) Pre/Post Recording 

This designates how many frames you are going to save of (PRE/POST) frames. 

(Pre: 10copies, Post: 500copies) Default: Pre – 0, Post – 1 

This is for the function in order to record previous one as well as post one. 


(10) Record Scheduling 

*How to use 

10 


1) Click the designated camera. 

2) Click recording scheduling methods button (Normal, Motion, Sensor, etc) 

3) Click suitable week day (Mon~Sun), Hour (0~24) or drag & drop. 

⇒ Normal : Steady recording during fixed time. 

⇒ Sensor : Temporary recording only sensor works. 

⇒ Motion : Recording only Motion Detection 

⇒ Watch : Only Display not recording. 

⇒ Sensor & Motion : Recording under sensor & Motion Detection. 

⇒ Normal & Event: Normally 1fps/sec, it is focusing on a specific camera when Motion 

or Sensor happens. 


3.4 Motion & Display Setting 

11 


* How to use 

1) Select Camera. 

2) Control the screen quality. 

(1) Color Adjustment 

- Color designating: After selecting camera, Brightness, Contrast, Saturation, Hue 

can be adjusted. Click ‘Default’ in order to make best condition. 

(2) Motion Detection 

- Rate of motion: This is a changed image ratio against between previous image and 

current. 

– Sensitivity Adjustment: Pixel (8*8size). 

*This plays important parts since when we starts to make a decision first. 

(3) Area Setting 

- Whole Area: It sets Detection. 

- Partial Area: Setting of partial area for motion detection. 

For partial area, put ‘add’ button on Image screen and Drag & Drop. 

You can make this partial area boxes up to ten. 

(4) Use Relay 

It sets how long and which relay to output. (Relay 1~4) 

* REF (example) 

In case of night shift, it can be notified to no.1 Relay output. (or Siren) 

*REF: This is not real image but 

recording image, so you must be 

careful with controlling this. 

* Controlling of motion recording 

3) Adjust sensor ratio and degree. 

Check ‘Display Detected Area 

and put ‘TEST’ button. 

Advisable: Motion ratio 10% 

Sensitivity 10% 


3.5 Network Setting 

- Use: Check in ‘Use’ and it permits RMS Connection. 

* How to use 

1) Check in ‘Use’. 

2) Select communicating channel. (LAN, ISDN, PSTN) 

3) Put Telephone, IP Address. Multi IP can be notified up to 8 places. 

* Make Notify Schedule by camera. 

12 


- Video Transfer method: JPEG or MPEG4 mode (In case of Modem, MPEG4 is advisable) 

- Notification: When sensor or motion happens, this RMS gives notification by E-Mail. 

4) Select the camera no. 

5) Click and Drag & Drop mouse to make scope to designate. 

6) In case of Motion & Sensor recording, you can select Event (Motion / Sensor or double selecting 

can be possible) 

If you set like this, it can send a notification when motion or sensor happens during this 

time scope through IP Address, which you already set, beep sound will be released to 

user. 


3.6 Sensor & Alarm Setting 

(5) 

(1) (2) 

(3) 

(4) 

13 


(1) Selecting sensor: Choose the sensor number 

(2) Option 

- Location of sensor: Input the sensor location 

- Sensor type: NC(Normal Close) or NO(Normal Open) 

- Connected camera : Setting of camera and free set to record when sensor turns on 

(6) 

(3) Sensor Values 

- Check Interval: Setting of sensor checking time & interval. 

- Output Port: Designate which camera’s recording. 

- Output Delay Time : Relay running time setting 

(4) Sensor Test: Test status of sensor 

* How to use 

1) Select camera number. 2) Input the sensor location (you do not have to) 

3) Select the sensor type (This is a designation for event happening if under NC or NO) 

4) Designating connecting camera. 

5) When Relay is being used, this makes possible to selct which no. of output. 

� TEST : This button is able to check if sensor connected or not. This blinks “ in red” 

when sensor comes in.. 

(5) Outer equipment control 

Click and input the equipment name (Lamp, ATM, etc), input the start time and ending time. 

Then it keeps ‘on’ within setting date and time and turns ‘off’. If you would not use it after 

setting, select relay no. and put ‘Del’key. 

You can control the this job from the remote site(RMS) such as main controlling center 


14 


(6) Emergency button 

This makes it easier for user to back up data set already from emergency button. 

When emergency happens, it sends recording image through RMS and converting and saving. 

Button automatically, you can choose only one among sensors. 

< Scenario > 

When no.3 camera works, all material from no.1.2 

camera should be back up on D:₩ 

It should notify through RMS when sensor and 

motion happens. 

Setting method (refer to left) 

(1) Enter into sensor on setting menu. 

(2) Click No.3 ‘sensor’ and check ‘use’ 

- Emergency button List - 

(3) Check ‘use’ and designate the location and 

click ‘Browse’ 

(4) Designate Event Backup Path (Real back up 

location) 

(5) Select camera (No. 1,2 camera) 

* Recording material will be saved into when you 

designate camera for back up. 

(6) Click ‘OK’ network on setting menu. 

(7) Check ‘Notification’ in ‘Use’ 

(8) ‘OK’ – Save and Exit 

(1) It should be motion (Event) Below screen will be turned if sensor connects event. 

◄ When sensor detects, alarm 

works. 

*REF: Since Event happens, recording is on for 3minutes (Post 3minutes) previous 

material (Pre 3minutes) will be Backup. 

(2) This is a screen of back 3minutes 

later in temporary back up path. 

*REF: In case of Scenario, Emergency folder will be made in C:₩ drive and back 

up in on. When Event backup turns up, it should be done before it will be 

deleted. 


3.7 User Setting 

(1) (2) (3) 

15 


(1) New user add 

- Put the user account/ Password, then give the authority (management mode/user mode/ 

search mode , back up mode, etc) 

(2) User list update 

- Select user and change the authority and click ‘update ‘ button. 

(3) Delete of user 

- Click the user and delete it. 

* The less user’s authority, the better for our security. 

3.8 Save and Exit 

- SAVE & EXIT 

Exit with the status that keeps what you’ve changed 

or set. 

- EXIT WITHOUT SAVE 

If you put this, previous setting is not effective. 


4 Searching Mode 

4.1 Search Mode Changing & Methods 

(2) Click ‘OK’ after putting Account and Password name. 

16 


(1) Click ‘Search’ button. 

- magnified image 

- Mark the exact ‘Account and Password’ 

(Default ID: test, Password: test) 

- Manage account and password for your 

own. 

- Refer to [3.7 User setting] for more 

information 

◄ Search mode 

(3) Select searching date 

(red mark) 

(previous month) 

(next month) 

. These red marks mean 

currently recording part. 


(4) Click time zone for searching. 

REF: Minute basis searching is available among 

60minutes 

Red mark means the location where you are 

searching. 

17 


(5) First Image will be 

shown on screen. 

(Refer to date) 

(6) Searching is going on 

when you put this button 

REF: Hour basis searching among 

24hours 

Different color will be shown 

according to recording way 

(Normal, Motion, Sensor, etc) 


4.2 Multi Searching Way 

When you search the other camera, you can use this function. 

18 


(1) Select the minute and hour part to search, then select right part of the searching part 

(1, 4, 9, 16 division) 

 

1 division 

4 division 

9 divison 

16 division 

Searching button 

(2) When you click divided screen (ex, 4screen) multi searching process(mark as percentage) 

and above screen is being showing . 

(3) Click and search with search button. Control the “speed” button Normal Speed search 

is general. If necessary, user’s designated search will be possible. 

* REF: At the multi search, only “multi search” mark is shown on the date & time 

window no other specific information shows. 

This multi usage is for only simultaneous search function. 

At the multi search mode, you can check other camera status as well at the same 

time. If you click ‘next camera group’ or ‘previous camera group’. 

The group is made of 1~4, 5~8, 9~12, 13~16 (4groups). In this mode, only video 

can be searched not sound. 


4.3 Search Screen Button Explanation 

1x 

1.5x 

2x 

Panorma 

Back play by 1fps 

Going back to the first data 

19 


Date (Year, Month, Day) 

Time (Hour, Minute, Second) 

Compression CODEC mark (JPEG, MPEG4) 

Camera number and file size 

Stop button 

Next camera group button choice (4 channel grouping) 

Previous group button choice (4 channel grouping) 

Normal Playing 

Reverse playing 

. Conversion to recording mode 

When you click this button during 

searching job. 

Going forward by 1fps 

Going forward the last data 



20 


21 


Searching TOOL (1) Conversion button Searching TOOL (2) 

Searching TOOL (1) – Recording Image quality control button 

- Sharp: Make the vague image clear 

- Blur: Make the wild image softer 

- B/W: Convert color into Black & WHITE 

- Cancel: Reverse into previous step, returning button 

- Zoom: With the mouse clicking, magnifying the image 

- Original: Returning to the first image 

Searching TOOL (2) – Saving & Printing of searched image 

Sound 

Print 

Color 

You can control Brightness, Contrast, 

Hue degree 

By adjusting this key as you want. 

(ex, ease searching at night time) 

Speed 

Normal Play, Quick Search mode 

-Speed is frame/sec for recording& 

display. 

User Setting mode 

- Normal Play: Searching through recorded frame speed. 

- Quick Search: Fast searching. 

- User Setting: Fast or slow searching with speed that fixed by user’s defined value.. 

- Mute: Deleting of sounding: we can use this when sound and video recorded. 

In case of checking: searching only video 

In case of not checking: Both video & sound are recorded 

Only video recorded (Blue) Sound & Video records together 

When you need to print the image 


22 


In case of printer setting done 

Left image may show up asking where to 

print, select ‘OK’ then you can print out. 

In case of printer setting not done 

Printer setting advises message comes 

out 


4.4 Motion Searching Way 

23 


Under the normal recording mode, designating specific area and analyzing 

it .(ex. This is very useful for stolen or lost goods) 

[ Motion Detection on the whole area ] [ Motion Detection on the partial area ] 

(2) Select the whole area button 

(3) Click the searching button 

(2) Select the whole area button 

(3) Click ‘ Add’ button. 

(4) Drag & Drop in order to make the 

box. (up to 5 ) 

(5) Click the search button. 

Motion on the whole area Motion on the partial area 

* Use add, select, delete, delete all button 

* 북마크 추가시에는 1분당 하나씩 추가 됩니다. 

(1) Motion rate and 

sensibility can be 

adjustable. 

This is not related 

with [3.4 Motion & 

Display function 

setting methods]. 

* REF 

- Motion ratio is the value between previous video and current one 

(The less, the more sensible one. Default: 5%, Recommended: 10~15 %) 

- Sensibility is the degree about converting values of picture (8*8 size) 

(The less, the more sensible one. Default: 20%, Recommended: 20 %) 


, 

4.5 How to use Book Mark 

< 북 마크 리스트 확인하기 > 

24 


Saving location function of current searched recording material (Time, Hour, Minute) 

(3) Click ‘Add Book mark’ for book marking 

(1) Click ‘Motion’ button. 

(2) When you click Book mark list button, list comes out. 

(1) Select Stop button 

(2) Click ‘Motion’ button. 

(4) Put the Comments 

name. (Being listed on 

book mark) 

This name can be 

amended. 

* REF: When there many lists if you select camera/all camera, It will be much better to 

watch. 

In case of Comments name amendment: reinput and click 

Short cut: Double click related list or 

select it with mouse, then It will be 

transferred to this location. 

Delete: omit related list 

Exit: exit from related list 


4.6 Data Saving Way 

(1) Still Image(JPEG) 

(2) Moving Image(AVI) 

25 


Saving function of searched data into disk with the form of JPEG file or AVI (Audio Video 

Interface) file. Normal PC can view it. 

(1) Select Moving Image (AVI) 

(2) Select Drivers (HDD, CD R/W, 

OTHER BACK UP DEVICE) 

(3) In case that is not on the specific 

location, do not check in Directory Set 

and click ‘OK’ 

To be continued previously 

(1) Select Still Image (JPEG) 

(2) Click ‘OK’ button 

(3) Saving ‘OK’ turns up 

Procedure (1)~(2) is the same 

(3) Check Directory Set part 

(4) Designate a specific location with 

clicking on ‘Browse’ button 

(5) If specific file location fixes, put the file 

name 

(6) Click ‘OK’ 

There left message turns up, if you do not 

put in file name 


(4) Click playing button on Search 

(5) Click the Stop’ button 

(6) ‘OK’ message comes out 

(7) Click ‘OK’ button. 

(3) View of AVI File 

26 


Stop 

(7) Click playing button on Search 

General: The percentage is increasing when searching is going on. 

Click the stop button when you need it. 

(8) Click the stop button 

(9) ‘OK’ message turns up 

(10) Click ‘OK’ button 

Window98 or 2000/XP has Media Player, so find AVI file name and double click it or 

Playing Media Player and open ->finding->ok and you can check out saving data. 

If you choose caption function on the menu, you can check out 


5 Log Viewer 

(1) 

(2) 

(3) 

(5) 

(4) 

(6) 

27 


(1) Click the ‘Log Viewer’ button 

on the monitoring mode. 

(As follows) 

(1) GedLog: log file. 

(2) Selected log file 

(3) You can search it by time table. 

Set up the date/time for searching->click the ‘Search’ button->Log presented on (2) part. 

To reload the old data: Cancel ‘Use’, click ‘Refresh’ button 

(4) File Information: Information of log file. 

(5) Log Information: Present the log data analysis. 

(6) View of event starting point screen in case of Event Log. 

(7) 

* REF: If log files 

exceed 1MB, old 

one remains 

backup version 

and new one will 

be created. All 

these are left on 

Ged log folder. 


(7) Graph : Graph of the event log 

- Analized View of graphic according to each event log view. 

28 


View of graphic according to date of specific date.. 

Go to previous date/next date of the camera. 

Go to next page.. 


- Manual: Sending the email just one time. 

- Schedule: Send the email frequently. 

* As a ‘Schedule Setting’, it send email 

frequently when you set this mode 

29 


[3.3] Refer to 

camera 

i 


6 Event Backup 

30 


You can use this function for back up the recorded event screen on designated 

directory. (Refer to 3.6 sensor& alarm (6) Event button) 

(1) Click ‘Event Backup’ button 

(1) If the message turns up like this, click ‘OK’ 

button 

Lookup Package copying image 

(2) Confirm again whether you do Event 

Back up or not. 

Click ‘ok’ and run the copy 

Back up screen 

* See the back up search when it is finished. 


7 Image Tool 

31 


This program for checking out authentication of FDD, HDD’s JPEG file. 

* Water marking function is already equipped 

* Way of playing: C:₩Program files₩DVR, double click imagetool.exe file 

(4) Image turns up. 

(5) Click ‘Verify Image’ button. 

◄ Initial screen of playing 

(1) Click ‘Open’ 

(2) Find & Choose file you want 

(3) Click ‘Open’ 

Check out the result of authentication 

not converted: This is authentic Image. 

Converted: This isn’t an authentic Image 

* REF: Other information: Camera no. Camera Name, Saving Time, Authority, 

User, Window Product key 


8 Backup 

* REF: You can not do both auto/manual back up. 

< SUPPORTING BACK UP DEVICE > 

8.1 Manual Backup Method 

32 


This is a part for back up into other saving equipment. There are Manual back/auto back 

up for user’s convenience. You can always check out at anywhere. 

HDD, DVD, DAT, CDRW, ONSTREAM, DLT, MO, ZIP, NETWORK DRIVE IF devices are DAT, 

ONSTREAM,DLT (LINEAR ACCESS device), we need a program which is converting 

LINEAR ACCESS device into RANDOM ACCESS device. (ex: DTA, DATMAN, ONSTREAM 

ECHO SOFTWARE ETC) 

Backing up what user want to pick up. Selecting Date->Camera->Time->Minute. 

(1) Double click this. 

* REF: to begin manually 

1) Begin->Program->DVR->Backup 

2) C:₩Program Files₩DVR₩Backup.exe 

(2) Data Loading is on the way 

(3) Put the Account & Password 

(4) Click ‘OK’. 

Change of icon color 

Back up is done (White) 

Back up is going 


33 


(5) Click ‘Select Media’ 

(6) Select back up device. 

(7) Click ‘OK’. 

(8) Users are designating Date->Camera->Hour 

->Minute 

* REF 

Checking point is to be backed up. 

With back up window open, 

The most recent information Refreshes. 

(9) Click ‘Back up start’ button. 

(10) if you need package, click ‘OK’ 

If you do not need it, click ‘Cancel’ 

Lookup Package is a program to make it 

view Back up data. 

(11) LookupPackage is copying on. 

(12) Click ‘Yes’ 

This is reconfirming if you want to Back up on 

related back up media 

(13) Click ‘Yes’ This is the confirming message that moving to the last part 

of recent back up area and let it do auto back up. 

* After finishing back up, Refer to 2.10 Backup way in order to check out if you want 

to know if it well done. 


8.2 Auto Backup Method 

1. Automatic Backup Setting 

34 


Automatic backing up with operating specific time scheduler. 

< Variety of Backup > 

1) DAILY BACKUP 

Mark Monday to Sunday and back up the previous data. 

2) Minute basis BACKUP 

Back up after designating minute and begin backing up. ex) If you set up 2minutes basis it 

is doing continuously. MAIN DISK& BACKUP device has two minutes difference. 

3) BASKET BACKUP 

Designating BASKET number and if in BASKET DATA is full BACKUP starts... 

Auto Startup 

Autoback definitely 

needs to be 

marked here 

(1) Moving to auto back up screen. 

LOG: Backup record stay here 

VIEW: back up searching program 

HIDDEN: Window hidden 

EXIT: Getting out of back up program 

This is the point where 

the last back up done 

as well as auto back up 

starting point. 

(2) Click ‘Add’ button or 

select related month/date 

and click ‘Add’ with right 

mouse part. 


35 


(3) Select the camera to back up 

(4) Select Backup device 

(5) Designate the location of related saving 

device 

(6) Click ‘ next’ 

Select All: select all camera at 

one time 

(7) Select the kind of back up 

(8) Click ‘Finish’ button 

Active 

When you use scheduler, if you 

do not use it, do not check 

here. 

(9) ’OK’ button makes whole day’s 

back up time same. 

‘CANCEL’ button makes specific date 

for back up. 


2. Auto Backup Update 

36 


This Job is done under “update” column as below. List can be shown as below when you 

click right button of mouse. 

3. Others 

< BACKUP LOG View > 

There Only 1 log for one job when It runs. 

BACKUP LOG (Following) – Auto back up size25 MB 

ADD : NEW SCHEDULE ADDS 

UPDATE : SCHEDULE AMENDS 

DELETE : SCHEDULE DELETES 

CLEAR ALL : ALL SETTING SCHEDULE 

ARE BEING DELETED 

< Media exchange > 

When CD is full and it needs to confirm, if you 

want to go or not. If you want to go on format 

CD click ‘OK’ 


9 Backup Viewer 

37 


This is a program for viewing back up material on a general PC or DVR. 

< Program running methods > 

1) Running at DVR 

(Run lookup.exe file in C:₩Program Files₩DVR folder.) 

2) General PC running methods: 

copy LookupPackage.exe (Backup viewer)on backup search program and open 

(automatically), C:₩Program Files₩Lookup is made , then you can run backup.exe 

(3) Click time 

part of camera 

. 

(1) Click the icon (2) Click year, month, date folder 

SAVING : image recording on FDD 

PRINT: printing 

SPEED: searching speed control/ mute (no sound) 

ORIGINAL: watching original 

* If mute is checked, sound does not play. 

* You can control speed accordingly. 

(4) When it shows screen, 

begin to search with searching 

button 

◄ Exit button 

◄ Water marking is on 


camera(1~16) 

Sensor/Relay 

Connection 

10 GoldenEye Installation 

10.1 Front or Back part of the System 

Powerc 

connection 

【 GOLDENEYE front 】 

HDD LED 

Reset 

Button 

【 GOLDENEYE Back 】 

Blue: mouse 

Purple: keyboard 

38 


Power 

Switch 

Outter monitor 

connecting 

part: 

BNC jack use 

FDD 

VGA Card 

Hard Rack 

(Option) 

Capture Card 

Overlay Board 

(RCA jack use) 

* Front / Back picture can be different according to model and upgraded status 

* REF: GED100, GED200 are connected Capture Board &camera Sound & Lan 

card are option.. 


10.2 Capture Card Connector and Receiver 

Capture Card Jumper J11 is for RS232, J12 is for RS422/485 

DVR 

COM1 COM2 

① 

39 


Line 1 connecting way: J12 (J32) port should be connected to PTZ Camera or Receiver 

Please refer to following. 

422Mdoe 485Mode 

1pin:RX- 1pin:TX-/RX- 

2pin:RX+ 2pin:TX+/RX+ 

3pin: TX- 

4pin:TX+ 

J11(or J31)port should be connected to PC serial port(COM1 or COM2). And Please check 

In PTZ box on camera setting, Set the port COM1 or COM2(set according to outer 

connection) 

Set the each protocol different according to receiver. Cable spec of line 2 is as below. 

[ 9 pins ] [ 25 pins ] 

Com1/2 J11(J31) Com1/2 J12(J32) 

(rx+) 2 

(tx+) 3 

(gnd) 5 

(rts) 7 

PTZ 

Camera 

2 (rx+) 

3 (tx+) 

5 (gnd) 

7 (rts) 

Camera 

Receiver 

② 

J12(J32) 

J11(J31) 

(rx+) 2 

(tx+) 3 

(gnd) 5 

(rts) 7 

JP1 

On: 485 Mode 

Off: 422 Mode 

2 (rx+) 

3 (tx+) 

5 (gnd) 

7 (rts) 


10.3 Sensors & Relays Connector Pin Spec 

SENSOR 

3~12V DC 

Lamp or Siren 

(Max 30W) 

DC 30V 1A 

AC 125V 0.3A 

40 


10.4 Back I/O Board with Sensors & Relays (SET) 

Video 1~ 16 

Common 1,2 

Composite Output 

(TV monitor) 

Relay 1~4 Sensor 1~ 16 

Lamp or Siren 

(Max 30W) 

DC 30V 1A 

AC 125V 0.3A 

SENSOR 

3~12V DC 

In case of using AC Power (110V, 

220V),specific relay out is needed. 

GROUND 1,2 


41 


10.5 Pan/Tilt Camera Protocol setting Values by Receiver 

2003.10 now 

index Receiver Baud rate Parity Data Bit 

Stop 

Bit 

Auto Pan Preset 

0 Dvna 9600 N 8 1 O X 

1 DY 9600 N 8 1 X O 

2 Fine 2400 N 8 1 O X 

3 Linlin 9600 N 8 1 O X 

4 Panasonic 19200 N 8 1 O X 

5 Pelco D 2400 N 8 1 O O 

6 Philips 9600 N 8 1 X X 

7 Serim 9600 N 8 1 X X 

8 Sungjin 4800 M 8 1 X X 

9 Vicon_1200R 4800 N 8 1 O X 

10 Dyuni 9600 E 8 1 O X 

11 DyuniTech_DRX50 9600 N 8 1 O X 

12 MP200 9600 N 8 1 O X 

13 KD6 9600 N 8 1 X X 

14 Samsung 9600 N 8 1 O X 

15 Oriental 4800 O 8 1 O X 

16 Techwin 9600 N 8 1 O X 

17 OmniView 9600 N 8 1 O X 

18 CNB 9600 N 8 1 X X 

19 CTNCOM 9600 N 8 1 X X 

20 Niko 2400 N 8 1 O X 

21 Winnertec 2400 N 8 1 O X 

22 PT-101 9600 N 8 1 O X 

23 PanasonicV12 O O 

24 Vicon_15UVS O X 

25 Securtex_B 4800 N 8 1 O X 

26 SmileCAM 19200 N 8 1 O O 

27 SCANDOMWE-2 9600 N 8 1 O X 

28 BBV 9600 N 8 1 O X 

29 KRE301 N 8 1 X X 

30 AD_RAS715LS 8 1 X X 

31 KALATEL_KTD312 8 1 X X 

32 VIDEOLARM 8 1 X X 

33 PELCO P 8 1 X O 


10.6 Sound Setting Method 

42 


Audio volume should be controlled in PC which has RMS installed S/W for sound recording 

< How to use > 

(1) Start->Program->Sub program 

->Entertainment->Volume control 

(2) If you click ‘Option->Properties’, 

you can see ‘properties info’ window 

(3) Check the mike volume on the 

properties information box of volume 

controller 

Sound card mixer equipment 

(4) Click ‘Advanced’ for mic input 

Option-Advanced. 


43 


(5) Check the mike output volume 

at other control part. 

Check Microphone Boost List. 

It can show +20db Gain in some cases. 

You can use recorder function to check 

Mike output before & after checking) 

You must check if sound input is 

working well. Checking is being done 

as follows; 

Start->program->Sub program 

->Entertainment->Sound recorder. 

*REF: Select ‘mute’ box if you want to save the voice directly without 

letting it go through speaker or only out put voice through speaker. 

This is the same as way adapted to 2way audio on RMS. 

Sometimes in case sound card does not support microwave 

amplifying function ‘advanced” button does not show up 

In this case, High sensible amplified mike should be in use

GoldenEye User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?