Operation Manual - Mrclab.com

More documents

Recommendations

Info

Connections of piping (3 and 4 in Fig, 1)HPLC-8100 HPLC ChromatographFig.3 Piping connection of Pump head with pressure transducer3.1-Backflushing capillaries3.2-Outlet valve housing3.3-Head set screws3.4-Inlet valve housing3.5-Eluent outlet4.1-Inlets to transducer4.2-Peek screws by hands4.3-De-areation screw4.4-Eluent outlet2. Rear panel view of the HPLC pumpFig. 4 Rear panel view of the HPLC pump4.1 Power connector 4.2 Fuse compartment4.3 ON/OFF Switch 4.4 12V Ventilator4.5 12V Ventilator 4.7 Gradient program trigger4.8 Plug for solvent organizer 4.9 RS-232 Interface3
HPLC-8100 HPLC ChromatographOperation of HPLC pumpHPLC pump is controlled by keyboard and work station of the computer control. The followingdescribes the operation of the keyboard. The work station of the computer control is described inthe Chapter four.1. Connection of power supplyHPLC Pump is equipped with a universal power supply for input voltage 220±20V Ac,frequency 50 ±0.5Hz. 1KVA stabilizer is required. Connect the power cable to the socket onthe rear panel of the instrument and switch on the device with the ON/OFF key, see (4.1) and(4.3) in Fig.4.CAUTION: Make sure that the main power supply is properly grounded and acorrect three-pronged power cable is used. Connecting the instrument to faulty powersockets can cause damages.2. User’s page characteristics and operationPress the key in 2.2 of Fig.2 at any time to make system purge, again press this key to stoppurging.CAUTION: If the purge is required, first loose “PEEK screw by hands”, see 4.2 inFig3, otherwise chromatographic column will be damaged!Self-test pageAfter switching on the instrument, firstly enter into the self-test status, display the self-test pageas shown the follows:BFRL HPLC-8100 HPLC PUMPRAM TEST OKBFRL HPLC-8100 HPLC PUMPEEPROM TEST OKPage of switching onFLOW►0.00ml P.max 19.0 MPaPRES 0.0mPa P.min 0.0 MPaASTOPTurn on the switch of the pump on this page. After completing the self-test of the pump, theabove page is appeared. Press 2.1 key in Fig.2 to make the pump START/STOP.CAUTION: Never run the HPLC Pump without liquid in the pump head or in the pistonbackflushing compartment. Operating the pump without solvent may lead to damage of thepump sealsSOP 1:4
Page 2 and 3: HPLC-8100 HPLC ChromatographCONTENT
Page 4 and 5: CHAPTER ONE PREFACEHPLC-8100 HPLC C
Page 8: HPLC-8100 HPLC ChromatographPress
Page 11 and 12: HPLC-8100 HPLC ChromatographFig. 5D
Page 13 and 14: HPLC pump technical parametersFlow
Page 15 and 16: HPLC-8100 HPLC ChromatographPrepara
Page 17 and 18: HPLC-8100 HPLC Chromatograph2. Rear
Page 19 and 20: HPLC-8100 HPLC ChromatographD2 LAMP
Page 21 and 22: HPLC-8100 HPLC ChromatographSimple
Page 23: Technical data of UV detectorWavele
Page 28 and 29: HPLC-8100 HPLC Chromatographplottin
Page 30 and 31: HPLC-8100 HPLC ChromatographSetting
Page 32 and 33: HPLC-8100 HPLC ChromatographFig.95)
Page 34 and 35: HPLC-8100 HPLC Chromatographof seve
Page 36: HPLC-8100 HPLC ChromatographFig.18T

Operation Manual - Mrclab.com

Create successful ePaper yourself

Delete template?

Save as template?