MPC-1000â¢ Fire Alarm System Control Unit Owner's ... - Faraday

More documents

Recommendations

Info

12100 OWNER'S MANUALIV. CONTROL UNIT INSTALLATIONPARTS SUPPLIED447039, 447040 or 447041 Back-box Assembly (red, white or black)413690, 413691 or 413692 Door Assembly (red, white or black)413535 Transformer Assembly (120VAC) 18965 #6-32 Keps Nuts (6)413688 Front Plate Assembly 29529-11 #6-32 x 1/4” Screws (16)413693 Main Board 942155 #8-32 Sems Screw, (4)413694 Display Board 942667 24K Ohm 1/2W Resistor (4)446054 Cable Assembly, 16 Pin 443269 Screwdriver447071 Lexan Window 447051 Owner’s Manual447072 Overlay 447058 Operating Instructions943966 Programming Keypad 942664 120 Ohm 1/2W Resistor (2)The fire alarm control unit must be mounted in a properly accessible location as required by applicablecodes. Any auxiliary battery box or other accessory not connected through a protective device or a circuitdesigned for remote connection must be within the same room and connected through electrical conduit.Installation is to be done only by qualified personnel who have thoroughly read and understood theseinstructions.CAUTIONSIt is recommended that the printed circuit boards be removed for any procedure that may cause dust,metal shavings, grease or any such matter that may affect the circuit boards and/or parts. There may beseveral sources of power into the control unit. Each source must be disconnected prior to installing orremoving modules, connecting or disconnecting wiring, and programming jumpers.CONTROL UNIT LOCATIONThe control unit should be located near an exit at ground level, where the normal ambient temperature ismaintained within the control unit specification (See General Specifications in Section III). The unitshould be in an area that is free of dust, vibration, moisture and condensation.ENCLOSURE MOUNTINGFollow the appropriate instructions for surface or semi-flush mounting.P/N 447051 Issue I Rev. CIV-1
12100 OWNER'S MANUALA. Surface Mounting InstructionsTo mount the enclosure:1. Mount the enclosure at a convenient height for viewing indicators and operating switches.2. Use four #10 lag screws (not supplied) to secure the control unit to the wall. The screw type andlength must support the control unit, options and battery set.Note: You may need a different screw type, depending on the wall material.3. The 12408 Auxiliary Power Supply or battery enclosure may be mounted immediately below the mainenclosure, close nipple, allowing a minimum of 1 inch in between the enclosures for clearancebetween the doors. Keeping the wire run to the control unit short will keep the voltage drop to aminimum.P/N 447051 Issue I Rev. CIV-2
Page 1 and 2: MPC-1000Fire Alarm System Control U
Page 4 and 5: 12100 OWNER'S MANUALVI.VII.Addressa
Page 6 and 7: 12100 OWNER'S MANUALI. INTRODUCTION
Page 8 and 9: 12100 OWNER'S MANUALPREFACEAlong wi
Page 10 and 11: 12100 OWNER'S MANUALII. DESCRIPTION
Page 12 and 13: 12100 OWNER'S MANUALAUXILIARY MODUL
Page 14 and 15: 12100 OWNER'S MANUALEVENT HISTORYTh
Page 16 and 17: 12100 OWNER'S MANUALGENERAL SPECIFI
Page 18 and 19: 12100 OWNER'S MANUALIII. CONTROL UN
Page 20 and 21: 12100 OWNER'S MANUALADDITIONAL OPER
Page 22 and 23: 12100 OWNER'S MANUAL12100 OPERATING
Page 26 and 27: 12100 OWNER'S MANUALB. Semi-Flush M
Page 28 and 29: 12100 OWNER'S MANUALF. Front Plate
Page 30 and 31: 12100 OWNER'S MANUALObserve polarit
Page 32 and 33: 12100 OWNER'S MANUALV. SYSTEM WIRIN
Page 34 and 35: 12100 OWNER'S MANUALSTATUS RELAYS A
Page 36 and 37: 12100 OWNER'S MANUALRS485 COMMUNICA
Page 38 and 39: 12100 OWNER'S MANUALTypical wiring
Page 40 and 41: 12100 OWNER'S MANUALStyle 6 provide
Page 42 and 43: 12100 OWNER'S MANUALAddressable/Ana
Page 44 and 45: 12100 OWNER'S MANUALTypical Base Wi
Page 46 and 47: 12100 OWNER'S MANUAL9161 Duct Housi
Page 48 and 49: 12100 OWNER'S MANUALAddressable Mod
Page 50 and 51: 12100 OWNER'S MANUALCONFIGURATION O
Page 52 and 53: 12100 OWNER'S MANUALDevice Monitor
Page 54 and 55: 12100 OWNER'S MANUALInterface Modul
Page 56 and 57: 12100 OWNER'S MANUALControl Module
Page 58 and 59: 12100 OWNER'S MANUALCONFIGURATION O
Page 60 and 61: 12100 OWNER'S MANUALIsolator Module
Page 62 and 63: 12100 OWNER'S MANUALVI. PROGRAMMING
Page 64 and 65: 12100 OWNER'S MANUALVII. MAINTENANC
Page 66 and 67: 12100 OWNER'S MANUALVIII. APPENDIX-
Page 68 and 69: 12100 OWNER'S MANUALBATTERY SIZE CA
Page 70 and 71: 12100 OWNER'S MANUALIX. APPENDIX-B:
Page 72 and 73: 12100 OWNER'S MANUALSupervisory Swi
Page 74 and 75:
12100 OWNER'S MANUALDEVICES FOR NOT
Page 76 and 77:
12100 OWNER'S MANUALFaradayCatalog
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
12100 OWNER'S MANUALX. APPENDIX-C:
Page 84 and 85:
12100 OWNER'S MANUALC. System Event
Page 86 and 87:
12100 OWNER'S MANUALXI. APPENDIX-D:
Page 88 and 89:
CR1INSTALLATION INSTRUCTIONS AND WI
Page 90 and 91:
12100 OWNER'S MANUALP/N 447051 Issu
Page 92 and 93:
413699 WIRINGFaraday P/N 447109Cabl
Page 94 and 95:
FCC Requirements - Part 68This equi
Page 96 and 97:
12408 WIRING24V Battery Set(7 to 38
Page 98 and 99:
CatalogNumberDescriptionAudibleVolt
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
The following table shows the dip s
Page 108 and 109:
Power Limited, Supervised12507/1250
Page 110 and 111:
Power Limited, Supervised12509/1251
Page 112 and 113:
SAMPLE LAYOUT FOR RELAY UNITSSAMPLE
Page 114:
12100 OWNER'S MANUALInitiating Devi
show all

MPC-1000â¢ Fire Alarm System Control Unit Owner's ... - Faraday

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

MPC-1000â¢ Fire Alarm System Control Unit Owner's ... - Faraday