English - Yamaha-Racingparts

More documents

Recommendations

Info

• The switch installed to the STD machine may be used as is. (See diagram 3.) (Digram 3) • The shifter switch function can be used by combining the harness and kit ECU. 1 To use the STD switch (left side) to function as the shifter switch, connect the wire sublead that was packaged with this set to the terminal that is normally connected to the left side horn. (See diagram 4.) However, if the resistor assembly is not installed, there is the possibility that the shifter switch will operate incorrectly in rainy weather. (See diagram 5.) NOTICE Do not bend the resistor assembly. It will cease to function if it is bent. 2 Pit road limiter ON OFF Not used Map select Lo → Map 1 Hi → Map 2 Pit road limiter ON ON PUSH=OFF Shifter switch Main switch Install the switch to the 2-pin black coupler underneath the fuel tank. Turning the switch ON cuts the ignition. – 64 – Engine stop switch Starter switch (Diagram 4) (Diagram 5) 5
NOTICE Do not connect the coupler for resistor (black, 2-prong) and the coupler for power (white, 2-prong). Connecting them may cause a malfunction. (See diagram 6.) • This harness has a coupler that connects to the 2D made data logger. (See diagram 7.) For details of the specifications of the data logger, please access the website. Webhttp://www.2d-kit-system.com/ (Diagram 7) Coupler – 65 –
Page 2 and 3:
Introduction • This manual is int
Page 4 and 5:
3 Tightening Torque List ..........
Page 6 and 7:
2 Kit Parts 2-1 Installing Engine P
Page 8 and 9:
3. Head-gasket, Cylinder Gasket Par
Page 10 and 11:
4. Piston Set (14B-116A0-70) Parts
Page 12 and 13:
8. Valve Spring Set (14B-A2110-71)
Page 14 and 15:
3. Installing the Lever Assembly Se
Page 16 and 17:
Ycci System Control You can use the
Page 18 and 19: 12. AIS-plug Set (5VY-A4890-70) Thi
Page 20 and 21: 13. Clutch Spring Set (4B1-A6330-70
Page 22 and 23: (Setting of back torque limiter of
Page 24 and 25: 15. Transmission Gear Parts List No
Page 26 and 27: NOTICE This set contains modified g
Page 28 and 29: - 24 - YZF-R1 Speed List Engine spe
Page 30 and 31: 38 36 29 28 33 27 25 26 29 28 37 35
Page 32 and 33: 17. Drive Sprockets Parts List This
Page 34 and 35: 2-2 Installing Chassis Parts 19. Oi
Page 36 and 37: 20. Shock Absorber Rear (14B-22210-
Page 38 and 39: - 34 - Performance and purpose of k
Page 40 and 41: 22. Front Fork ASSY Parts List No.
Page 42 and 43: - 38 - Performance and purpose of k
Page 44 and 45: 23. Spring Front Fork Parts List No
Page 46 and 47: 5. Remove the push rod and fit the
Page 48 and 49: References Front and rear load chan
Page 50 and 51: 25. Front Spare Wheel ASS’Y (4C8-
Page 52 and 53: 27. Throttle Set (14B-C6300-70) Par
Page 54 and 55: 28. Throttle Set (14B-C6300-80) Par
Page 56 and 57: 29. Tube Guide (5VY-26243-80) Parts
Page 58 and 59: 31. Cable Interface (13S-8533A-70)
Page 60 and 61: Self-Diagnosis Functions • The EC
Page 62 and 63: Installing Wire Harness: 1. Remove
Page 64 and 65: NOTICE The wire from the ACM is des
Page 66 and 67: Installing Rectifier/Regulator: 1.
Page 70 and 71: • This harness comes with a coupl
Page 72 and 73: - 68 -
Page 74 and 75: 3 Tightening Torque List Engine To
Page 76 and 77: Engine To be tightened Part No. Par
Page 82 and 83: Chassis To be tightened Part No. Pa
Page 84 and 85: Chassis To be tightened Part No. Pa
Page 86 and 87: Installing the Crankcase Tightening
Page 88 and 89: 5 YZF-R1 Wiring Diagram - 84 -
show all

English - Yamaha-Racingparts

Create successful ePaper yourself

Delete template?

Save as template?