Operating and Installation Instructions Display device KERN KFS-T

More documents

Recommendations

Info

6.6 LinearizationLinearity shows the greatest deviation of a weight display on the scale to the value ofthe respective test weight according to plus and minus over the entire weighingrange. If linearity deviation is discovered during a testing instrument control, you canimprove this by means of linearization.• Carrying out linearization is restricted to specialist staff possessingwell acquainted with the workings of weighing scales.• The test weights to be used must be adapted to the weighing scale’sspecifications; see chapter “testing instruments control”.• Observe stable environmental conditions. Stabilisation requires acertain warm-up time.• Do not remove the adjustment weight during linearization in stepLAOD 1 to LOAD 4, merely increase it instead. Conversely do notremove the adjustment weight during step LAOD 4 to LOAD 1,merely increase it instead.• After successful linearisation you will have to carry out calibration;see chapter “testing instruments control”.Tab. 1: Adjustment weights“LOAD1 – LOAD4”MAX LOAD 1 LOAD 2 LOAD 3 LOAD 43kg 0.5kg 1kg 2kg 3kg6kg 1kg 2kg 4kg 6kg15kg 3kg 5kg 10kg 15kg30kg 5kg 10kg 20kg 30kg60 kg 10kg 20kg 40kg 60kg120 kg 30kg 60kg 60kg 150kg300 kg 50kg 100kg 200kg 300kg600 kg 100kg 200kg 400kg 600kg1.5 t 3000kg 5000kg 1000kg 1500kg3 t 5000kg 1000kg 2000kg 3000kg16 KFS-T-BA_IA-e-1213
Call menu item linearization , see chap. 6.5 Confirm menu setting with .Ensure that there are no objects on the weighing plate. “LoAd 1” will be displayed after standstill control has been carried out. Put thefirst adjustment weight approx. 1/4 Max (see table 1) carefully in the centre of theweighing pan.“LoAd 2” will be displayed after standstill control has been carried out. Put the second adjustment weight approx. 2/4 max (see table 1) carefully in thecentre of the weighing pan. “LoAd 3” will be displayed after standstill control hasbeen carried out. Put the third adjustment weight approx. 3/4 max (see table 1) carefully in thecentre of the weighing pan. “LoAd 4” will be displayed after standstill control hasbeen carried out. Put the forth adjustment weight approx. 4/4 max (see table 1) carefully in thecentre of the weighing pan.After successful standstill control the balance carries out a selftest, then itautomatically returns to weighing mode.• An adjusting error or incorrect adjusting weight will be indicated by the errormessage; repeat adjustment procedure.• You can cancel adjustment by pressing any key with the exception ofand .KFS-T-BA_IA-e-1213 17
Page 4 and 5: 1 Technical dataKERNDisplayDivision
Page 6 and 7: 2.1 Overview of displayWeight displ
Page 8 and 9: 2.2 Keyboard overviewKeyFunction Tu
Page 10 and 11: 3.4 Monitoring of Test ResourcesIn
Page 12 and 13: 6.3 Unpacking/installationCarefully
Page 14 and 15: Call up menu: Switch-on balance and
Page 18 and 19: 7 Operation7.1 Start-up Press and t
Page 20 and 21: 7.6.1 Determination of the average
Page 22 and 23: 7.7 TotalizationAdding-up during we
Page 25 and 26: Display and output sum „Total“:
Page 27 and 28: 7.7.2 Automatic adding-upWith this
Page 30 and 31: Activate function For menu setting
Page 32 and 33: 7.8.1 Tolerance check for target qu
Page 34 and 35: 7.8.2 Tolerance check for target we
Page 36 and 37: Start tolerance check Place load an
Page 38 and 39: Change settingsConfirm selected men
Page 40 and 41: F9 PAParity42 Pr0* No parity bit44
Page 42 and 43: 9.1 Printer modePrintout example (K
Page 44 and 45: 11 Error messages, troubleshooting
Page 46 and 47: 12.3 How to connect the platform Di
Page 48 and 49: Change settingsConfirm selected men
Page 50 and 51: Dual range balanceConfirm with, the
Page 52: 13 Declaration of conformityEG-Konf

Operating and Installation Instructions Display device KERN KFS-T

Create successful ePaper yourself

Delete template?

Save as template?