Operating and Installation Instructions Display device KERN KFS-T

More documents

Recommendations

Info

Dual range balanceConfirm with, then the following menu items can beselected by .dESCPosition decimal point availableselection 0, 0.0, 0.00, 0.000, 0.0000,0.00000inC div 1 inC 1 Readability forinC 2inC 5inC 101. Weighing rangeSelectable 1, 2, 5, 10, 20,50inC 20inC 50div 2 inC 1 Readability forinC 2inC 5inC 102. Weighing rangeSelectable 1, 2, 5, 10, 20,50inC 20inC 50CAP CAP 1 Balance capacity (Max) 1st weighingrangeCAP 2Adjust weighing system after configuration.Balance capacity (Max) 2nd weighingrangeCAL nonLin Adjustment, see chap. 6.5LinEAr For linearisation see chapter 6.650 <strong>KFS</strong>-T-BA_IA-e-1213
Multi-interval balanceConfirm byavailable., after that the following menu items arePosition decimal point availableselection 0, 0.0, 0.00, 0.000, 0.0000inC div 1 inC 5 Readability forinC 5inC 5inC 101. Weighing rangeSelectable 1, 2, 5, 10, 20,50inC 20inC 50div 2 inC 1 Readability forinC 2inC 5inC 102. Weighing rangeSelectable 1, 2, 5, 10, 20,50inC 20inC 50CAP CAP 1 Balance capacity (Max) 1st weighingrangeCAP 2Balance capacity (Max) 2nd weighingrangeAdjust weighing system according to configuration.CAL nonLin Adjustment, see chap. 6.5LinEAr Linearisation see chap. 6.6<strong>KFS</strong>-T-BA_IA-e-1213 51
Page 4 and 5: 1 Technical dataKERNDisplayDivision
Page 6 and 7: 2.1 Overview of displayWeight displ
Page 8 and 9: 2.2 Keyboard overviewKeyFunction Tu
Page 10 and 11: 3.4 Monitoring of Test ResourcesIn
Page 12 and 13: 6.3 Unpacking/installationCarefully
Page 14 and 15: Call up menu: Switch-on balance and
Page 16 and 17: 6.6 LinearizationLinearity shows th
Page 18 and 19: 7 Operation7.1 Start-up Press and t
Page 20 and 21: 7.6.1 Determination of the average
Page 22 and 23: 7.7 TotalizationAdding-up during we
Page 25 and 26: Display and output sum „Total“:
Page 27 and 28: 7.7.2 Automatic adding-upWith this
Page 30 and 31: Activate function For menu setting
Page 32 and 33: 7.8.1 Tolerance check for target qu
Page 34 and 35: 7.8.2 Tolerance check for target we
Page 36 and 37: Start tolerance check Place load an
Page 38 and 39: Change settingsConfirm selected men
Page 40 and 41: F9 PAParity42 Pr0* No parity bit44
Page 42 and 43: 9.1 Printer modePrintout example (K
Page 44 and 45: 11 Error messages, troubleshooting
Page 46 and 47: 12.3 How to connect the platform Di
Page 48 and 49: Change settingsConfirm selected men
Page 52: 13 Declaration of conformityEG-Konf

Operating and Installation Instructions Display device KERN KFS-T

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?