Operating and Installation Instructions Display device KERN KFS-T

More documents

Recommendations

Info

F9 PAParity42 Pr0* No parity bit44 Pr1 Odd parity44 Pr2 Even parityF10 S0 Sd0 on* Autom. printout enabled on zero displaySd0 ofAutom. printout disabled on zero displayF11 AC 5 AC 0For automatic totalizing see chap. 7.7.2With this function the individual weighing valuesare automatically added into the summationmemory when the balance is unloaded andedited, when an optional printer is connected.5 AC 1*Manual totalizing, see chap. 7.7.1With this function the individual weighing valuesare added into the summation memory byF12 bkDisplay background illuminationpressing and edited, when an optionalprinter is connected.5 bkL0 Background illumination off5 bkL1*Automatic background illumination on whenweighing pate is loaded or key pressed.5 bkL2 Continuous background lightingFactory settings are marked by *.40 KFS-T-BA_IA-e-1213
9 RS 232C interfaceThe RS 232C interface allows a bi-directional data exchange from the balance toexternal devices. This data exchange is asynchronous using ASCII - Code.The following conditions must be met to provide successful communication betweenthe weighing system and the printer.• Use a suitable cable to connect the display unit to the interface of the printer.Faultless operation requires an adequate KERN interface cable.• Communication parameters (Baud rate, parity, see chap. 8) of display deviceand printer must match.Pin allocation of balance output plug:Pin nr. Signal Input/Output Function2 RXD Input Receive data3 TXD Output Transmit data4 DTR Output HIGH5 GND - Signal ground6 - -7 - -8 - -9 GND - Signal groundInterface cable:PCD-SUB9PBalanceD-SUB9PTXD32RXRX23TXDGN55GNKFS-T-BA_IA-e-1213 41
Page 4 and 5: 1 Technical dataKERNDisplayDivision
Page 6 and 7: 2.1 Overview of displayWeight displ
Page 8 and 9: 2.2 Keyboard overviewKeyFunction Tu
Page 10 and 11: 3.4 Monitoring of Test ResourcesIn
Page 12 and 13: 6.3 Unpacking/installationCarefully
Page 14 and 15: Call up menu: Switch-on balance and
Page 16 and 17: 6.6 LinearizationLinearity shows th
Page 18 and 19: 7 Operation7.1 Start-up Press and t
Page 20 and 21: 7.6.1 Determination of the average
Page 22 and 23: 7.7 TotalizationAdding-up during we
Page 25 and 26: Display and output sum „Total“:
Page 27 and 28: 7.7.2 Automatic adding-upWith this
Page 30 and 31: Activate function For menu setting
Page 32 and 33: 7.8.1 Tolerance check for target qu
Page 34 and 35: 7.8.2 Tolerance check for target we
Page 36 and 37: Start tolerance check Place load an
Page 38 and 39: Change settingsConfirm selected men
Page 42 and 43: 9.1 Printer modePrintout example (K
Page 44 and 45: 11 Error messages, troubleshooting
Page 46 and 47: 12.3 How to connect the platform Di
Page 48 and 49: Change settingsConfirm selected men
Page 50 and 51: Dual range balanceConfirm with, the
Page 52: 13 Declaration of conformityEG-Konf

Operating and Installation Instructions Display device KERN KFS-T

Create successful ePaper yourself

Delete template?

Save as template?