Fire-Lite Alarms MS-9600 Addressable Fire Control Panel

More documents

Recommendations

Info

Product DescriptionAccessoriesBB-55FThe BB-55F battery box may be used to house two 25 AH batteries, two 60 AHbatteries or one 100 AH battery. When the CHG-120F is mounted in the BB-55F, two25 AH or one 60 AH battery may also be housed in the battery box.bb-55f.cdr1.8.4 CHG-120F Battery ChargerReferenceManualReferenceManualThe CHG-120F is capable of charging up to 120 AH lead-acid batteries with the MS-9600 FACP. The FACP battery charger must be disabled when using the CHG-120F.The batteries and charger can be housed in the Fire•Lite BB-55F battery box which canbe mounted up to 20 feet away from the control panel. Note that when using the BB-55F for housing the charger and batteries greater than 25AH, multiple BB-55Fs arerequired. Refer to the CHG-120F Manual for additional information.1.8.5 AnnunciatorsACM Series LED Zone Type AnnunciatorsThe ACM Series Annunciators remotely display alarm and trouble status as well assystem status. In addition, they can provide remote Acknowledge, Silence, Reset andDrill functions. For more detailed information, refer to the appropriate annunciatormanual. Following is a list of annunciators which can be used with the MS-9600.• ACM-16ATF Annunciator Control Module annunciates 16 zones with 16 redalarm LEDs and 16 yellow trouble LEDs. In addition, it has a System TroubleLED, an On Line/Power LED and a local piezo sounder. It also has switches forFACP Acknowledge, Silence, Reset and Drill. It has rotary address switches andwill accept up to three AEM-16ATF Expanders• AEM-16ATF Annunciator Expander Module annunciates 16 zones with 16 redalarm LEDs and 16 yellow trouble LEDs• AFM-16ATF Annunciator Fixed Module annunciates 16 zones with 16 red alarmLEDs and 16 yellow trouble LEDs. In addition, it has a System Trouble LED, anOn Line/Power LED and a local piezo sounder. It also has switches for FACPAcknowledge, Silence, Reset and Drill. It is fixed at address ‘1’• ACM-32AF Annunciator Control Module annunciates 32 alarm zones with 32red LEDs. In addition, it has a System Trouble LED, an On Line/Power LEDand a local piezo sounder. It also has a switch for local piezo silence. It hasrotary address switches and will accept one AEM-32AF Expander• AEM-32AF Annunciator Expander Module annunciates 32 alarm zones with 32red LEDs• AFM-16AF Annunciator Fixed Module annunciates 16 alarm zones with 16 redalarm LEDs. In addition, it has a System Trouble LED, an On Line/Power LEDand a local piezo sounder. It also has a switch for local piezo silence. It is fixedat address ‘1’• AFM-32AF Annunciator Fixed Module annunciates 32 alarm zones with 32 redLEDs22 MS-9600 PN 51335:D 11/06/01
Getting StartedProduct DescriptionReferenceManualReferenceManualLCD-80F Remote Fire AnnunciatorThe LCD-80F annunciator is a compact 80-character backlit LCD remote fireannunciator that is capable of displaying English language text. It mimics the displayon the control panel and will annunciate device type, point alarm, trouble orsupervisory condition, zone assignment plus any custom alpha labels programmed intothe FACP. The annunciator also provides system status LEDs to display AC Power,Alarm, Trouble, Supervisory and Alarm Silenced conditions. Additionally, the LCD-80F is capable of remotely performing critical system functions such as Acknowledge,Silence, Reset and Drill.Communications between the control panel and the annunciator is accomplished over aserial interface employing the EIA-485 communication standard. Up to 32 LCD-80Fannunciators may be connected to the EIA-485 circuit. The annunciators may bepowered from the host FACP or a remote UL listed filtered power supply such as theFire•Lite FCPS Series. For more detailed information, refer to the LCD-80F manual.LDM Series Lamp Driver Modules (Graphic Annunciator)The LDM Series Lamp Driver Modules, which consist of the LDM-32F master andLDM-E32F expander modules, are used to provide an interface to a custom graphicLED annunciator. The master module provides power and control for a maximum ofthree expander modules. The LDM-32F and LDM-E32F have output connectors whichare used to drive lamps or LEDs and input connectors which are used for remote switchfunctions. Refer to the LDM Series Lamp Driver Modules manual for a completedescription.1.9 Getting StartedThe following is a brief summary of the minimal steps involved in bringing anMS-9600 on-line:• Install Backbox and Main Circuit Board (refer to "Mounting" on page 24)• Address and Install Intelligent Devices (refer to the SLC Wiring Manual)• Enter Autoprogramming (refer to "Autoprogram" on page 87)• Resolve Programming Conflicts• Go to Point Program to Enter Specific Data (refer to "Point Program" on page43). Use the right and left arrow keys to navigate between devices.MS-9600 PN 51335:D 11/06/01 23
Page 1 and 2: PN: 51335:D ECN 01-535Fire Alarm Co
Page 3 and 4: Installation PrecautionsWARNING - S
Page 5 and 6: Table of ContentsSECTION 1: Product
Page 7 and 8: Table of Contents3.7.5: System.....
Page 9 and 10: It is imperative that the installer
Page 11 and 12: Ack/Step Sil ence Drill ResetHold 2
Page 13 and 14: Features and OptionsProduct Descrip
Page 15 and 16: SpecificationsProduct DescriptionEI
Page 17 and 18: CircuitsProduct Description1.5 Circ
Page 19 and 20: ComponentsProduct Description1.6.2
Page 21: AccessoriesProduct Description1.8 A
Page 25 and 26: MountingInstallation1.75“5.1 cm2.
Page 27 and 28: Power2.2 PowerInstallationWARNING:
Page 29 and 30: UL Power-limited Wiring Requirement
Page 31 and 32: 2.6.1 4XTMF Transmitter Module Inst
Page 33 and 34: 2.6.3 SLC-2 Expander ModuleReferenc
Page 35 and 36: ABCDEFGHI JKL MNOPRS TUV WXYMODEHOL
Page 37 and 38: 2.6.5.4 ACM and AFM Series Annuncia
Page 39 and 40: 3.2 User Programming!The MS-9600 is
Page 41 and 42: To access user Programming mode, pr
Page 43 and 44: PROGRAMMING1=POINT PROGRAM2=ZONE SE
Page 45 and 46: NO DETECTORINSTALLEDEdit Detector S
Page 47 and 48: EDIT DETECTOR1=ENABLED2=TYPE3=VERIF
Page 49 and 50: EDIT DETECTOR1=ZONE ASSIGNMENT00 **
Page 51 and 52: 1=STANDARD ADJECTIVE2=STANDARD NOUN
Page 53 and 54: 1. The cursor is on the first lette
Page 55 and 56: 3.6.1.2.3 Edit Module Screen for Mo
Page 57 and 58: Master Programming LevelProgramming
Page 59 and 60: EDIT MONITOR1=PRE-SIGNAL2=PASEdit M
Page 63 and 64: MODULES1=ADD2=DELETE3=EDITModules S
Page 65 and 66: CONTROL TYPE1=BLANK2=BELL-CIRCUIT3=
Page 69 and 70: EDIT CONTROL1=ADJECTIVE/NOUN2=DESCR
Page 71 and 72: ZONE SETUP1=ENABLE2=DISABLE3=ZONE 9
Page 73 and 74:
Master Programming LevelProgramming
Page 75 and 76:
3.6.4 System SetupPROGRAMMING1=SYST
Page 77 and 78:
SYSTEM SETUP1=TROUBLE REM2=BANNER3=
Page 79 and 80:
SYSTEM SETUP1=TIMERS2=NAC3=RELAYSSy
Page 81 and 82:
TIMER1=AC LOSS DELAYTimer Screen #2
Page 83 and 84:
Master Programming LevelProgramming
Page 85 and 86:
• Steady - a continuous output wi
Page 87 and 88:
PROGRAMMING1=SYSTEM SETUP2=AUTOPROG
Page 89 and 90:
HISTORY1=VIEW EVENTS2=ERASE HISTORY
Page 91 and 92:
PROGRAMMING1=HISTORY2=WALKTEST3=OPT
Page 93 and 94:
PROGRAMMING1=PASSWORD CHANGE2=CLEAR
Page 95 and 96:
PROGRAMMING1=PASSWORD CHANGE2=CLEAR
Page 97 and 98:
3.7 Maintenance Programming LevelTo
Page 99 and 100:
PROGRAMMING1=POINT PROGRAM2=HISTORY
Page 101 and 102:
Pressing 3 while viewing Program Ch
Page 103 and 104:
PROGRAMMING1=WALKTEST2=SYSTEM3=ZONE
Page 105 and 106:
SECTION 4Operating Instructions4.1
Page 107 and 108:
4.3 Normal OperationWith no alarms
Page 109 and 110:
4.5 Alarm OperationPressing the Ack
Page 111 and 112:
4.7 Process Monitor Operation4.8 Ha
Page 113 and 114:
4.16 Synchronized NAC Operation4.17
Page 115 and 116:
4.20 Special System Timers4.20.1 Si
Page 117 and 118:
4.22 Read StatusRead Status functio
Page 119 and 120:
Pressing the down arrow key, while
Page 121 and 122:
4.22.5 TimersPressing 2 while viewi
Page 123 and 124:
READ STATUS1=ANNUNCIATORS2=FUTURE U
Page 125 and 126:
Drift CompensationDrift compensatio
Page 127 and 128:
SECTION 55.1 OverviewPower Supply C
Page 129 and 130:
Table 5.3 contains columns for calc
Page 131 and 132:
APPENDIX AA.1 CorrelationsSetup and
Page 133 and 134:
DETECTOR ZONE ASSIGNMENTAddress Dev
Page 135 and 136:
DETECTOR ZONE ASSIGNMENTAddress Dev
Page 137 and 138:
MONITOR/CONTROL MODULE ZONE ASSIGNM
Page 139 and 140:
APPENDIX BThe following table provi
Page 141 and 142:
Numerics300 Series addressable devi
Page 143 and 144:
see also Notification ApplianceCirc
Page 145 and 146:
NotesMS-9600 PN 51335:D 11/06/01 14
Page 147 and 148:
Limited WarrantyThe manufacturer wa
show all

Fire-Lite Alarms MS-9600 Addressable Fire Control Panel

Create successful ePaper yourself

Delete template?

Save as template?