Q150T S/E/ES Sample Preparation System Instruction Manual

More documents

Recommendations

Info

Q150T Sample Preparation System Outer ring O-ring Sample holder Figure 7-8. Metal evaporation insert adapted for upwards evaporation 10473 - Issue 3 56 Q150T - Instruction Manual FTM Electrode extension Wire basket
7.5 Glow Discharge Insert Q150T Sample Preparation System This section describes the installation of the glow discharge insert (Part No. 10262). WARNING – HIGH VOLTAGES AND HIGH VACUUM This equipment produces high voltages and high vacuum in its operation. Figure 7-9. Glow discharge insert 1. Check the machine is not operating. 2. Press down firmly on the top cover to release the latch. 3. Lift the top cover and rest it against its stop. 4. Turn the two securing buttons to release and remove the installed insert (see Figure 7-1). Q150T ES users only: If the insert is a carbon rod type you may have to remove the rods first (see page 5151). To do this, check that the securing buttons are restraining the insert and open the lid assembly and rest it against the top cover assembly. Then, using a 2.5mm hex key, release the rod clamping screws and withdraw the rods. Close the lid assembly and release the insert by turning the securing buttons. Now remove the insert. 5. Prepare the glow discharge insert for installation by removing from any packaging, plastic bags etc. Check the ‘O’ ring in the outer ring of the lid assembly for damage or debris and clean or replace as required. 6. Remove the shutter by unscrewing the two retaining M3 screws (see Figure 7-10). Place the insert in position in the outer ring of the lid assembly carefully locating the M3 screw head in the rim of the insert in the slot to the right of the outer ring. 7. Lock the insert in position by turning the securing buttons until their flanges overlap the insert. 8. Plug the insert lead into the socket on the hinge assembly. Q150T - Instruction Manual 57 10473 - Issue 3
Page 1 and 2:
Q150T S/E/ES Sample Preparation Sys
Page 3 and 4:
Contents Section Contents Q150T Sam
Page 5 and 6: List of Figures Q150T Sample Prepar
Page 7 and 8: Health and Safety Q150T Sample Prep
Page 9 and 10: 1.2 Sputter Coating Q150T Sample Pr
Page 11 and 12: 2.3 Connections Q150T Sample Prepar
Page 13 and 14: 2.3.4 Vacuum Connections Q150T Samp
Page 15 and 16: 3 Operation Q150T Sample Preparatio
Page 17 and 18: Q150T Sample Preparation System Fig
Page 19 and 20: 4 Working with Profiles Q150T Sampl
Page 21 and 22: 4.2.1 Creating a New Profile To cre
Page 23 and 24: 4.3 Materials Q150T Sample Preparat
Page 25 and 26: Q150T Sample Preparation System 6.
Page 27 and 28: 5.1.3 Aluminium thin film Q150T Sam
Page 29 and 30: 5.3 Metal Evaporation Q150T Sample
Page 31 and 32: 5.6 Ramped Profile Q150T Sample Pre
Page 33 and 34: 5.6.3 Adjusting coating thickness Q
Page 35 and 36: 5.7 Glow Discharge Q150T Sample Pre
Page 37 and 38: 6 Instrument Management Q150T Sampl
Page 39 and 40: 6.2.1 Network Q150T Sample Preparat
Page 41 and 42: 6.2.3 Vacuum Q150T Sample Preparati
Page 43 and 44: 6.2.5 Hardware Q150T Sample Prepara
Page 45 and 46: Q150T Sample Preparation System You
Page 47 and 48: Q150T Sample Preparation System 6.6
Page 49 and 50: 7 Accessories Q150T Sample Preparat
Page 51 and 52: 7.2 Carbon Rod Insert Q150T Sample
Page 53 and 54: Q150T Sample Preparation System 7.
Page 55: Q150T Sample Preparation System 6.
Page 59 and 60: 7.6 Rotacota Stage Q150T Sample Pre
Page 61 and 62: 7.8 102mm Stage and Gearbox Q150T S
Page 63 and 64: 7.10 Film Thickness Monitor (FTM) Q
Page 65 and 66: 7.13 Rotating Vacuum Spigot Q150T S
Page 67 and 68: 7.15 Spares Q150T Sample Preparatio
Page 69 and 70: 8 Service and Maintenance Q150T Sam
Page 71 and 72: Q150T Sample Preparation System Err
Page 73 and 74: Name Default Q150T Sample Preparati
Page 75 and 76: Name Default Q150T Sample Preparati
Page 77 and 78: 9.3 Technical Specification Q150T S
Page 79 and 80: Deposition Rate (nm/min) 4 0 .0 3 5
Page 81 and 82: 9.5 Return of Goods Q150T Sample Pr
Page 83 and 84: 10 Index A access code ............
Page 85: Quorum Technologies Units 1 & 2 Ede
show all

Q150T S/E/ES Sample Preparation System Instruction Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?