Toshiba B-EX4T1 Owners Manual - The Barcode Warehouse

More documents

Recommendations

Info

2. PRINTER SETUP ENGLISH VERSION EO1-330892.3 Loading Supplies2.3.1 Loading the Media(Cont.)NOTE:Do not over-tighten the LockingRing of the Supply Holder.7. Align the projection of the Supply Holder with the groove of theSupply Shaft, and push the Supply Holder against the media until themedia is held firmly in place. This will centre the mediaautomatically.Then turn the Locking Ring clockwise to secure the Supply Holder.Supply HolderGuide ShaftProjectionSupply ShaftLocking RingGrooveIn the case of a label rolled withthe print side facing inside.In the case of a label rolled withthe print side facing outside.MediaGuide Shaft8. Place the media between the Media Guides, adjust the Media Guidesto the media width, and tighten the Locking Screw.9. Check that the media path through the printer is straight. The mediashould be centred under the Print Head.Media GuidePrint HeadSupply HolderLocking ScrewMediaMedia GuideE2- 6
2. PRINTER SETUP ENGLISH VERSION EO1-330892.3 Loading Supplies2.3.1 Loading the Media(Cont.)10. Lower the Print Head Block until it stops.11. After loading the media, it may be necessary to set the MediaSensors used to detect the print start position for label or tag printing.Setting the Feed Gap Sensor position(1) Manually move the Media Sensor so that the Feed Gap Sensor ispositioned at the centre of the labels. (• indicates the position of theFeed Gap Sensor).GapLabel Media Sensor Feed Gap Sensor (•)NOTE:Be sure to set the black marksensor to detect the centre of theblack mark, otherwise a paperjam or no paper error may occur.Setting the Black Mark Sensor position(1) Pull about 500 mm of media out of the front of the printer, turn themedia back on itself and feed it under the Print Head past the sensorso that the black mark can be seen from above.(2) Manually move the Media Sensor so that the Black Mark Sensor isin line with the centre of the black mark on the media. (• indicatesthe position of the Black Mark Sensor).Black MarkMediaMedia SensorBlack Mark Sensor (•)E2- 7
Page 3 and 4: TOSHIBA Barcode PrinterB-EX4T1 SERI
Page 7 and 8: Safety SummaryENGLISH VERSIONDiscon
Page 10 and 11: 1. PRODUCT OVERVIEW ENGLISH VERSION
Page 16 and 17: 2. PRINTER SETUP ENGLISH VERSION EO
Page 30: 2. PRINTER SETUP ENGLISH VERSION EO
Page 71 and 72:
2. PRINTER SETUP ENGLISH VERSION EO
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
2.PRINTER SETUPENGLISH VERSION EO1-
Page 83 and 84:
2.PRINTER SETUPENGLISH VERSION EO1-
Page 85 and 86:
3. ON LINE MODE ENGLISH VERSION EO1
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
4. MAINTENANCE ENGLISH VERSION EO1-
Page 93 and 94:
5. TROUBLESHOOTING ENGLISH VERSION
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
6. PRINTER SPECIFICATIONS ENGLISH V
Page 101 and 102:
7. SUPPLY SPECIFICATIONS ENGLISH VE
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
APPENDIX 1 MESSAGES AND LEDSENGLISH
Page 111 and 112:
APPENDIX 2 INTERFACEENGLISH VERSION
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
APPENDIX 3 PRINT SAMPLESENGLISH VER
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
APPENDIX 4 GLOSSARIESENGLISH VERSIO
show all

Toshiba B-EX4T1 Owners Manual - The Barcode Warehouse

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?