38AG OMP #92323.pdf - MinnPar

More documents

Recommendations

Info

INTRODUCTION•The primary purpose of this manual is to provide the user with a thorough understandingof the proper operating procedures necessary to comply with the intended useof the CONDOR®, and to provide the information necessary to maintain and service theCONDOR®.THE OPERATOR'S MANUAL MUST BE RETAINED ON THE UNIT AT ALL TIMES.Do not attempt to operate or service the CONDOR® until you have readand understood all information provided in this manual. Familiarize yourselfwith the functions and operations of the upper and lower controls. Agood understanding of the controls, their limitations, and their capabilitieswill maximize operating efficiency and safety. The various decals attachedto this machine also contain vital safety and operational instructions.Read the decals before operating this machine.It is YOUR RESPONIBILITY to follow safe procedures while operating the CONDOR®.The manufacturer of this unit cannot control the wide range of applications that may beused in carrying out a variety of jobs. Therefore, it is THE USER'S RESPONSIBILITY toconsider the safety of all personnel when making decisions regarding the unit's intendeduse.It is also YOUR RESPONSIBILITY to understand and obey all federal, ai id localregulations regarding the safe operation and use of aerial work platforms. A copy ofthe ANSI/SIA 92.5-1992 Manual of Responsibilities is attached for your useCalavar Corporation reserves the right to modify, improve, add, and/or delete certaindesign features of its products without any obligation to incorporate new features intoproducts previously sold. Our manuals are continually updated to reflect thesechanges.DO NOT ALTER OR MODIFY THIS UNIT WITHOUT PRIOR WRITTEN APPROVALFROM THE MANAGEMENT OF CALA VAR CORPOR4770N•.•SERVICE & MAINTENANCE••Many of the parts used in the manufacture of the CONDOR® have specific properties,and the manufacturer recommends that replacement parts be purchased through CalavarCorporation in order to ensure the original integrity of the fieoduct. Repairs andadjustments should only be made by trained and qualified personne:. 'lease refer to themaintenance and parts sections of the Calavar Operation, Maintenance, & Parts Manualfor information on service and maintenance of the CONDOR®.NOTE:Please refer to the Calavar Parts section of the Operation, Maritenance, &Parts Manual for information pertaining to your machine.MANUAL 92323SEPTEMBER 1994
Page 1: BOOM-SUPPORTEDELEVATING WORK PLATFO
Page 5 and 6: INTRODUCTIONThe primary purpose of
Page 7 and 8: IMPORTANT: A COPY OF THE ANSI/SIA 9
Page 9 and 10: Models 38AG, 47AG —Gas & Diesel P
Page 11 and 12: Model 47AE —Electric PowerUPPER C
Page 13 and 14: D. TRAVELDriving the machine may on
Page 15 and 16: APPENDIX: DECALS ILLUSTRATION[Model
Page 17 and 18: NOTESMANUAL 92265-001SEPTEMBER 1994
Page 21 and 22: INTRODUCTIONThe primary purpose of
Page 23 and 24: CA IL. INVII 14CALAVAR CORPORATIONC
Page 25 and 26: 9. The CONDOR® has been designed t
Page 27 and 28: NOTES4MANUAL 92323-002SEPTEMB ER 19
Page 29 and 30: B. PRE-DELIVERY INSPECTION SHEET (P
Page 31 and 32: NOTE:DO NOT SHIP ANY RETURN PARTS W
Page 33 and 34: NOTES10MANUAL 92323-002AUGUST 1994
Page 35 and 36: NOTES12MANUAL 92323-002SEPTEMBER 19
Page 37 and 38: APPENDIX EIAILSO/011111CALAVAR CORP
Page 41 and 42: GRI D NO.This catalog covers:This g
Page 43 and 44: ITThis catalog covers:_'D620D- 11 S
Page 45 and 46: Thi s catalog covers::D620D- LI S03
Page 47 and 48: Thi s catalog covers:FD620D- [11 S0
Page 49 and 50: GRI D NO.This catalog covers:FDG2OD
Page 51 and 52: Thi s' catalog covers:FD620D [1] S0
Page 53 and 54:
This catalog covers:FD620D- LI S03G
Page 55 and 56:
This catalog covers:FD620D- Eli S03
Page 57 and 58:
INTRODUCTIONThe primary purpose of
Page 59 and 60:
TABLE OF CONTENTS (Continued)FIGURE
Page 61 and 62:
FIGURE B—Recommended Spare Parts
Page 63 and 64:
FIGURE C—How to Order Parts1. Whe
Page 65 and 66:
CONDOR® MODEL 38AG —Serial Numbe
Page 67 and 68:
FIGURE 1.2—Decals Installation211
Page 69 and 70:
FIGURE 1.3—Cover Installation3 RE
Page 71 and 72:
FIGURE 2.1 —Carriage Assembly517
Page 74 and 75:
FIGURE 2.2—Steering InstallationI
Page 76 and 77:
FIGURE 2.3—Drive Installation (Tw
Page 78 and 79:
FIGURE 2.3A—Torque Hub AssemblyIT
Page 80 and 81:
FIGURE 2.3C—Brake AssemblyITEM PA
Page 82 and 83:
FIGURE 2.5—Fuel Tank & Battery In
Page 84 and 85:
FIGURE 2.6— Carriage Hydraulic In
Page 86 and 87:
FIGURE 2.8—Lift/Steer Manifold As
Page 88 and 89:
FIGURE 2.10—Proportional Drive Va
Page 90 and 91:
FIGURE 2.11—Speed Control (2-Posi
Page 92 and 93:
FIGURE 2.12—Kawasaki Gasoline Eng
Page 94 and 95:
FIGURE 3.1—Turret InstallationITE
Page 96 and 97:
FIGURE 3.2 Rotation InstallationITE
Page 98 and 99:
FIGURE 3.4—Hydraulic Motor, Turre
Page 100 and 101:
FIGURE 3.5—Turret Hydraulic Insta
Page 102 and 103:
FIGURE 3.5—Turret Hydraulic Insta
Page 104 and 105:
FIGURE 3.6—Turret Electrical Inst
Page 106 and 107:
FIGURE 3.7—Lower Control Box Asse
Page 108 and 109:
FIGURE 3.8—Electrical Box Assembl
Page 110 and 111:
FIGURE 4.2—Arm Lift Cylinder Asse
Page 112 and 113:
FIGURE 5.1—Boom InstallationITEM
Page 114 and 115:
FIGURE 5.2—Aluminum Boom Assembly
Page 116 and 117:
FIGURE 5.3—Boom Extension Cylinde
Page 118 and 119:
FIGURE 5.4—Boom Extension Cylinde
Page 120 and 121:
FIGURE 5.5—Master Leveling Cylind
Page 122 and 123:
FIGURE 5.6—Slave Leveling Cylinde
Page 124 and 125:
FIGURE 5.7—Slave Leveling Cylinde
Page 126 and 127:
FIGURE 5.8—Holding Valve Assembly
Page 128 and 129:
FIGURE 5.9—Boom Hydraulic Install
Page 130 and 131:
FIGURE 5.10- Hose Installation Diag
Page 132 and 133:
FIGURE 5.11—Track AssemblyITEM PA
Page 134 and 135:
FIGURE 6.1—Platform InstallationC
Page 136 and 137:
FIGURE 6.2—Platform Assembly14137
Page 138 and 139:
•= •1°FIGURE 6.3-Platform Wiri
Page 140 and 141:
FIGURE 7.1 —Kubota Diesel Engine
Page 142 and 143:
FIGURE 7.1A—Diesel Engine Electri
Page 144 and 145:
FIGURE 7.1C—Radiator Installation
Page 146 and 147:
FIGURE 7.2—Auxiliary Lowering Pow
Page 148 and 149:
FIGURE 7.4—Dual Fuel Carburetor A
Page 150 and 151:
FIGURE 7.6—Dual Fuel Carburetor A
Page 152 and 153:
FIGURE 7.8—Travel Alarm Assembly
Page 154 and 155:
FIGURE 7.10—Air Line to Platform
Page 156 and 157:
FIGURE 7.12—Foam-Filled Tires Ass
Page 158 and 159:
FIGURE 7.14—Five-Foot-Wide Platfo
Page 160 and 161:
FIGURE 8.1 —List of Schematics &
Page 162 and 163:
!••22/23 cit.!, 655 65A• HEAD
Page 164 and 165:
?A5A8A1 013 11426/2726/271 a22/2317
show all

38AG OMP #92323.pdf - MinnPar

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?