High-Performance SAB 80C517A/83C517A-5 8-Bit CMOS Single ...

More documents

Recommendations

Info

SAB 80C517A/83C517A-5Table 6Performing a MDU-CalculationOperation 32 Bit/16 Bit 16 Bit/16 Bit 16 Bit * 16 BitFirst WriteLast WriteMD0MD1MD2MD3MD4MD5D'endLD'endD'endD'endHD'orLD'orHMD0MD1MD4MD5D'endLD'endHD'orLD'orHMD0MD4MD1MD5M'andLM'orLM'andHM'orHFirst ReadLast ReadMD0MD1MD2MD3MD4MD5QuoLQuoQuoQuoHRemLRemHMD0MD1MD4MD5QuoLQuoHRemLRemHMD0MD1MD2MD3PrLPrHTable 7Shift Operation with the MDUOperationFirst WriteLast WriteFirst ReadLast ReadNormalize, Shift Left, Shift RightMD0MD1MD2MD3ARCONMD0MD1MD2MD3least significant bytemost significant bytestart of conversionleast significant bytemost significant byteAbbreviationsD'end : Dividend, 1st operand of divisionD'or : Divisor, 2nd operand of divisionM'and : Multiplicand, 1st operand of multiplicationM'or : Multiplicator, 2nd operand of multiplicationPr : Product, result of multiplicationRem : RemainderQuo : Quotient, result of division...L : means, that this byte is the least significant of the 16-bit or 32-bit operand...H : means, that this byte is the most significant of the 16-bit or 32-bit operandSemiconductor Group 48
SAB 80C517A/83C517A-5I/O PortsThe SAB 80C517A has seven 8-bit I/O ports and two input ports (8-bit and 4-bit wide).Port 0 is an open-drain bidirectional I/O port, while ports 1 to 6 are quasi-bidirectional I/O portswith internal pull-up resistors. That means, when configured as inputs, ports 1 to 6 will bepulled high and will source current when externally pulled low. Port 0 will float when configuredas input.Port 0 and port 2 can be used to expand the program and data memory externally. During anaccess to external memory, port 0 emits the low-order address byte and reads/writes the databyte, while port 2 emits the high-order address byte. In this function, port 0 is not an open-drainport, but uses a strong internal pull-up FET. Port 1, 3, 4, 5 and port 6 provide several alternatefunctions. Please see the "Pin Description" for details.Port pins show the information written to the port latches, when used as general purpose port.When an alternate function is used, the port pin is controlled by the respective peripheral unit.Therefore the port latch must contain a "one" for that function to operate. The same applieswhen the port pins are used as inputs. Ports 1, 3, 4 and 5 are bit- addressable.The SAB 80C517A has two dual-purpose input ports. The twelve port lines at port 7 and port8 can be used as analog inputs for the A/D converter. If input voltages at P7 and P8 meet thespecified digital input levels (V IL and V IH ) the port can also be used as digital input port.In Hardware Power Down Mode the port pins and several control lines enter a floating state.For more details see the section about Hardware Power Down Mode.Semiconductor Group 49
Page 1: High-Performance8-Bit CMOS Single-C
Page 5 and 6: SAB 80C517A/83C517A-5The pin functi
Page 7 and 8: SAB 80C517A/83C517A-5Pin Definition
Page 15: SAB 80C517A/83C517A-5Pin Definition
Page 18 and 19: SAB 80C517A/83C517A-5Program Memory
Page 20 and 21: SAB 80C517A/83C517A-5Accesses to XR
Page 22 and 23: SAB 80C517A/83C517A-5Control of XRA
Page 24 and 25: SAB 80C517A/83C517A-5Table 1:Behavi
Page 26 and 27: SAB 80C517A/83C517A-5Special Functi
Page 28 and 29: SAB 80C517A/83C517A-5Table 2Special
Page 34 and 35: SAB 80C517A/83C517A-5Figure 4Block
Page 36 and 37: SAB 80C517A/83C517A-5Table 4CCU Com
Page 38 and 39: SAB 80C517A/83C517A-5CompareIn comp
Page 40 and 41: SAB 80C517A/83C517A-5Figure 6Block
Page 42 and 43: SAB 80C517A/83C517A-5Figure 9Compar
Page 44 and 45: SAB 80C517A/83C517A-5Figure 10Inter
Page 46 and 47: SAB 80C517A/83C517A-5Figure 10Inter
Page 50 and 51: SAB 80C517A/83C517A-5Power Saving M
Page 52 and 53: SAB 80C517A/83C517A-5Power Down Mod
Page 54 and 55: SAB 80C517A/83C517A-5Table 8Status
Page 56 and 57: SAB 80C517A/83C517A-5Serial Interfa
Page 58 and 59: SAB 80C517A/83C517A-5Watchdog Units
Page 60 and 61: SAB 80C517A/83C517A-5Figure 12Funct
Page 62 and 63: SAB 80C517A/83C517A-5Absolute Maxim
Page 64 and 65: SAB 80C517A/83C517A-5Notes for page
Page 66 and 67: SAB 80C517A/83C517A-5AC Characteris
Page 68 and 69: SAB 80C517A/83C517A-5Program Memory
Page 70 and 71: SAB 80C517A/83C517A-5AC Characteris
Page 72 and 73: SAB 80C517A/83C517A-5ROM Verificati
Page 74 and 75: SAB 80C517A/83C517A-5Application Ci
Page 76 and 77: Table 1:Behaviour of P0/P2 and RD /

High-Performance SAB 80C517A/83C517A-5 8-Bit CMOS Single ...

Create successful ePaper yourself

Delete template?

Save as template?