Load Balancing Router User's Guide - Edimax

More documents

Recommendations

Info

Virtual ServersThis feature allows you to make Servers on your LAN accessible to Internet users. Normally, Internetusers would not be able to access a server on your LAN because:• Your Server's IP address is only valid on your LAN, not on the Internet.• Attempts to connect to devices on your LAN are blocked by the firewall in The <strong>Load</strong> Balancer.The "Virtual Server" feature solves these problems and allows Internet users to connect to yourservers, as illustrated below.Figure 4-2: Virtual ServersNote that, in this illustration, both Internet users are connecting to the same IP Address, but usingdifferent protocols.Connecting to the Virtual ServersOnce configured, anyone on the Internet can connect to your Virtual Servers. They must use The<strong>Load</strong> Balancer's Internet IP Address (the IP Address allocated by your ISP).e.g.http://205.20.45.34ftp://205.20.45.34• To Internet users, all virtual Servers on your LAN have the same IP Address. This IP Address isallocated by your ISP.• This address should be static, rather than dynamic, to make it easier for Internet users to connectto your Servers. However, you can use the Dynamic DNS feature (explained later in this chapter)to allow users to connect to your Virtual Servers using a URL, instead of an IP Address.e.g.HTTP://my_domain_name.dyndns.orgFTP://my_domain_name.dyndns.orgPage 28
Figure 4-3: Virtual ServerSettings – Virtual ServerEnableServer TypeLAN IPAddressUse this to Enable or Disable each Virtual server as required.Select the desired Server type. If the type of Server you wish to use is not listed,use the Custom Virtual Server screen to define your own type.Enter the IP address of the PC on your LAN which is running the required Serversoftware.Each PC should have a fixed IP address, or have a reserved IP address. (See theHost IP section earlier in this chapter for details on reserving an IP address.)Page 29
Page 3 and 4: TABLE OF CONTENTS1: INTRODUCTION ..
Page 5 and 6: 1: IntroductionCongratulations on t
Page 7 and 8: Other Features• 4-Port Switching
Page 9 and 10: Also, some Status and Error conditi
Page 11 and 12: Figure 1-3: Windows TFTP utility•
Page 13 and 14: • You can and should set a passwo
Page 15 and 16: DHCP IP AddressRangeARP ProxyLAN An
Page 17 and 18: • For each PC connected to the LA
Page 19 and 20: Optional • Host name - This is re
Page 21 and 22: 7. Select "Set up my connection man
Page 23 and 24: 3: Advanced Port SetupOverview• P
Page 25 and 26: Load BalanceThis screen is only ope
Page 27 and 28: Advanced PPPoEThe screen is require
Page 29 and 30: 4: Advanced ConfigurationOverviewTh
Page 31: Host NetworkBinding• Bind WAN por
Page 35 and 36: • Protocol Type - Select the netw
Page 37 and 38: Outgoing Port RangeIncoming Protoco
Page 39 and 40: Settings - Dynamic DNSDynamic DNSSe
Page 41 and 42: Settings - Multi DMZEnableNameFor S
Page 43 and 44: NATNAT (Network Address Translation
Page 45 and 46: Advanced FeaturesThis screen allows
Page 47 and 48: InterfaceBindingProtocol &Port Bind
Page 49 and 50: Settings - URL FilterAccess GroupBl
Page 51 and 52: Block Well-knownportsUser-defined P
Page 53 and 54: System Filter ExceptionSystem Filte
Page 55 and 56: Policy ConfigurationWhen you use Qo
Page 57 and 58: Settings - SNMPSystemInformationTra
Page 59 and 60: SyslogThis feature can send real ti
Page 61 and 62: Admin Password ScreenThe password s
Page 63 and 64: 8: Advanced LAN ConfigurationOvervi
Page 65 and 66: GatewayInterfaceMetricThe IP Addres
Page 67 and 68: 9: Operation and StatusOperationOnc
Page 69 and 70: Buttons • Refresh - Update the da
Page 71 and 72: NAT StatusThis screen is displayed
Page 73 and 74: Appendix ASpecificationsModelDimens
Page 75 and 76: Figure B-2: IP Address (Win 95)Ensu
Page 77 and 78: 5. Ensure your TCP/IP settings are
Page 79 and 80: 5. Ensure your TCP/IP settings are
Page 81: Solution 2:The Load Balancer proces

Load Balancing Router User's Guide - Edimax

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?