USER MANUAL - Teltonika

More documents

Recommendations

Info

GeneralThis area is dedicated for protocol specific options.Static:This is the configuration setup for when you select the static protocol.Filed name Sample Explanation1. IPv4 address 192.168.99.162 Your routers address on the WAN network2. IPv4 netmask 255.255.255.0 A mask used to define how “large” the WAN network is3. IPv4 gateway 192.168.99.254 Address where the router will send all the outgoing traffic4. IPv4 broadcast 192.168.99.255 Broadcast address (autogenerated if not set). It is best to leave thisblank unless you know what you are doing.5. custom DNS servers 8.8.8.8 8.8.6.6 Usually the gateway has some predefined DNS servers. As such therouter, when it needs to resolve a hostname (“www.google.com”,“www.cnn.com”, etc…) to an IP address, it will forward all the DNSrequests to the gateway. By entering custom DNS servers the routerwill take care of host name resolution. You can enter multiple DNSservers to provide redundancy in case the one of the server fails.DHCP:When you select the DHCP protocol you can use it as is, because most networks will not require any additionaladvanced configuration.32
PPPoE. This protocol is mainly used by DSL providers:This is the configuration setup for when you select PPPoE protocol.Filed name Sample Explanation1. PAP/CHAP username test Your username and password that you would use to connect to your2. PAP/CHAP password your_password carriers network.3. Access Concentrator isp Specifies the name of access concentrator. Leave empty to autodetect.4. Service Name isp Specifies the name of the service. Leave empty to autodetect.AdvancedThese are the advanced settings for each of the protocols, if you are unsure of how to alter these attributes it is highlyrecommended to leave them to a trained professional:Static:Field name Sample value Explanation1. Bring up on boot On Specifies whether the interface will be configured and brought upwhen the router boots up. Disabling will render your WANconnection non-functional2 Disable NAT On/Off Toggle NAT on and off.3. Override MAC address 00:0C:43:30:50:38 Override MAC address of the WAN interface. If your ISP gives youa static IP address it might also bind it to your computers MAC33
Page 1 and 2: 1USER MANUAL
Page 3 and 4: Table of ContentsLegal notice .....
Page 5 and 6: SAFETY INFORMATIONIn this document
Page 7 and 8: IntroductionThank you for purchasin
Page 10 and 11: Setting up your routerInstallationA
Page 12 and 13: Start -> Settings -> Network Connec
Page 14 and 15: 6. By default the router is going t
Page 16 and 17: Enter the default password, which i
Page 18 and 19: Function explanationsThe following
Page 20 and 21: Field Name Sample Value Explanation
Page 22 and 23: 8. Country LT Country code.Addition
Page 24 and 25: This tri-graph illustrates average
Page 26 and 27: WAN(x)Graphs the amount of traffic
Page 28 and 29: This graph shows a concise history
Page 30 and 31: number that fallsbetween 0000 and99
Page 34 and 35: address (i.e. that IP will only wor
Page 36 and 37: Should you be asked enter the secre
Page 38 and 39: 4. DHCP-Options 6,192.168.2.1,192.1
Page 40 and 41: SecurityEncryption - There are many
Page 42 and 43: amount of failed or passed health c
Page 44 and 45: DMZBy enabling DMZ for a specific i
Page 46 and 47: 192.168.55.240 255.255.255.240 Appl
Page 48 and 49: Field name Description Notes1. Enab
Page 50 and 51: Field name Description1. Enable Ena
Page 52 and 53: Field name Explanation1. Enabled Sw
Page 54 and 55: Phase 1 and Phase 2 must be configu
Page 56 and 57: SystemsConfiguration WizardThe conf
Page 58 and 59: The final step allows you to config
Page 60 and 61: Important notes:Leaving “Keep set

USER MANUAL - Teltonika

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?