Operations manual - FP-IMS

More documents

Recommendations

Info

Operator <strong>manual</strong> T 1000 TrendDiagnostic code “23” + “Cassette“ indicates aletter jam. The letter was franked, but did notcome out of the machine. Carefully removethe letter and continue with franking.“Cassette”“23 Cassette”“Service” +“Service”If the message “Cassette” appears in thedisplay, there is no ribbon cassette in place ora wrong one is used. Place a new ribboncassette into the compartment and press the“C” key.The diagnostic code “23” with the word“Service” and/or “Cassette” mean a letter is inthe feed path.Press any key (except the “C” key) andremove the letter. Check to make sure theribbon is tight.If there is no letter jam, the ribbon cassette isused up. Press the “C” key to finish theprinting process and change the ribboncassette.Automatic time/date module is defective.Please call your servicing dealer.If this message appears, call your servicingdealer for urgently required measures to savepostage registers.Caution! The machine can be used for threeadditional months or 3,000 franks before itwill automatically lock and become inoperable.See chapter 8.1 for information on the faultsand problems specific to TELESET loading.38
TroubleshootingProblemDisplay is blankPostage values are nottransferred from scale tothe T 1000 TrendPossible causes and solutionsNo power:• Check to make sure T 1000 Trend is plugged in andthe keylock switch is in position ”I”.Meter without power:• Check to see if franking machine is plugged in andthe keylock switch is in position ”I”.Data transfer interrupted:• Check if interface cables are tightly connected toboth units.Scale interface key is not activated:• Check if the scale symbol appears in the display. Ifnot, press the ”Scale interface” key.T 1000 Trend does not Franking machine in ”0” account:print • Press the ”C” key and select a departmentalaccount between 1 and 9.Scale interface on, no scale connected:• If symbol is displayed and no scale isconnected, press the "Scale interface" key once toturn off the interface function.Franking machine is out of postage:• If ”Limit End” is displayed, the franking machine isout of postage. Load new postage.T 1000 Trend is blocked • Turn off the machine and turn it back on.Letter jam • Carefully remove the letter, turn off the machineand turn it back on.Displayed date or timeare incorrect• Change the date / time <strong>manual</strong>ly. See chapter 7.1.39
Page 1: Operator ManualFranking machine T 1
Page 4 and 5: Explanation of display symbols (Fig
Page 6 and 7: Operator manual T 1000 Trend8 Loadi
Page 8 and 9: Operator manual T 1000 Trend8
Page 10 and 11: Operator manual T 1000 TrendIncorre
Page 12 and 13: Operator manual T 1000 Trend3.2.3 C
Page 14 and 15: Operator manual T 1000 Trend3.4 Tur
Page 16 and 17: Operator manual T 1000 TrendAfter p
Page 18: Operator manual T 1000 Trend5.2 Pri
Page 21 and 22: Electronic postage scale6 Electroni
Page 23 and 24: Basic programming7 Basic programmin
Page 25 and 26: Basic programming• The new high p
Page 27 and 28: Loading postage - TELESET modem8 Lo
Page 29 and 30: Loading postage - TELESET modemWhen
Page 31 and 32: Loading postage - TELESET modemTabl
Page 33 and 34: Loading postage - TELESET voice8.2
Page 35 and 36: Maintenance, upkeep and service9 Ma
Page 37: Troubleshooting10 TroubleshootingIn
Page 41 and 42: Declaration Of Conformity41
Page 43 and 44: Service12 ServiceEvery T 1000 Trend

Operations manual - FP-IMS

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?