SIMOVERT Master Drives Communication Board CBD

More documents

Recommendations

Info

Master DrivesCBD05/20/992 Mounting instructions2 Mounting instructionsIf a 6SE7090-0XX84-0KA0 adapter board is required, the backplane bus adapter (local bus adapter LBA, Order No.:6SE7090-0XX84-4HA0) must first be installed before the board is used. Otherwise the CBD is inserted directly on theCU board.Installing the LBA bus expansion:♦ Remove the CU board (lefthand slot in the electronics box)using the handles after first removing the connecting cableto the PMU and both retaining screws♦ Insert the LBA bus expansion in the electronics box(position, refer to the diagram) so that it snaps into place♦ Re-insert the CU into the lefthand slot, tighten-up theretaining screws on the handles, and insert the connectingcable to the PMUFig. 2.1Installing the local bus adapter♦ Insert CBD on the lower position of the adapter board andscrew into place. Insert the adapter board into slot 2(righthand side) or slot 3 (center) of the electronics box, andscrew into place. Only one of each option board type maybe inserted in the electronics box. If only one option board isinserted, then it must always be inserted at slot 2 (right).The adapter board with the CBD attached can either be inserted at slot +1.B2 or +1.B3. Please refer to Fig. 2.2 for theslot designations. Please note, that slot +1.B3 is the center slot in the electronics box!Electronics box slot+1.B1 (left) Standard board CU+1.B3 (center)+1.B2 (right)Option boardsBoardsNOTEEach option board can only be used once in the electronics box!CBD / SCB1 / SCB2 / TSYCBD / SCB1 / SCB2 / TSY / TB (e. g. T100 or T300)TB (technology boards, e. g. T300), must always be inserted in slot +1.B2 (RIGHT in the electronics box)! Whena TB board is inserted, a TSY option board cannot be used.If only one option board is used, then this must always be inserted in slot +1.B2 (RIGHT in the electronics box)!Siemens AG 477 759 4070 76 J AA-74 7SIMOVERTMASTERDRIVES Betriebsanleitung/OperatingInstructions
Master DrivesCBD05/20/992 Mounting instructions-X187ADAPTERBOARD+1.B1+1.B3+1.B2-X185CBDX438Fig. 2.2CBD on adapter board with bus connector and electronics box with free slots +1.B2 and +1.B3NOTEWhen installing the CU control electronics board (slot +1.B1) and the option board(s), ensure that the handlesare screwed flush with the surface of the electronics box (so that the board isn’t tilted)!8 Siemens AG 477 759 4070 76 J AA-74SIMOVERTMASTERDRIVES Betriebsanleitung/OperatingInstructions
Page 1 and 2: SIMOVERT Master DrivesCommunication
Page 3: Table of Contents5 Start-up........
Page 6 and 7: Master DrivesCBD05/20/990 Definitio
Page 8 and 9: Master DrivesCBD05/20/991 Product d
Page 12 and 13: Master DrivesCBD05/20/993 Connectin
Page 18 and 19: Master DrivesCBD05/20/994 Data tran
Page 40 and 41: Master DrivesCBD05/20/995 Start-up5
Page 58 and 59: Master DrivesCBD05/20/996 Troublesh
Page 60 and 61:
Master DrivesCBD05/20/996 Troublesh
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Master DrivesCBD05/20/997 Appendix7
show all

SIMOVERT Master Drives Communication Board CBD

Create successful ePaper yourself

Delete template?

Save as template?