SIMOVERT Master Drives Communication Board CBD

More documents

Recommendations

Info

Master DrivesCBD05/20/994 Data transfer via DeviceNet4.3 Process data area (PZD)4.3.3 Instructions and rules regarding process data processingExample:Connecting-up the setpoints in the drive:P443.01 (Source main setpoint) = 3032P554.01 (Source ON/OFF1) = 3001 (using control word 1)P584.01 (Source Technology regulator enable) = 3004 (using control word 2)P526.01 (Source Technology regulator setpoint) = 3005Connecting-up the actual values in the drive:P694.01 = 968 (status word 1)P694.02 = 218 (main actual value as 32-bit value -->)P694.03 = 218 (same parameter No. in 2 consecutive indices)P694.04 = 553 (status word 2)P694.05 = 3 (output voltage)P694.06 = 4 (output current)P694.07 = 5 (output power)4.3.3 Instructions and rules regarding process data processing♦ The lowest significant byte (for words) is always sent first and the lowest significant word (for double words).♦ Control word 1 must always be contained in the 1st word of the received setpoints. If control word 2 is required,this must be located in the 4th word.♦ Bit 10 “control from the PLC” must always be set in control word 1, otherwise the drive will not accept the newsetpoints and control words.♦ The consistency of the process data is guaranteed within the data of a DeviceNet IO Message Connection.Even if more than 4 words are required, the data is not sent to the drive until all data has been transferred throughthe DeviceNet bus. Thus, all setpoints and control words are accepted by the drive at the same instant.Siemens AG 477 759 4070 76 J AA-74 35SIMOVERTMASTERDRIVES Betriebsanleitung/OperatingInstructions
Master DrivesCBD05/20/995 Start-up5.1 Parameterization5 Start-up5.1 Parameterization...Section, Start-up / parameterization “Expert application“ of the drive Instruction ManualOption boards?yesPossible option boards:SCB, TSY, CB, TBnoP052 = 4"Hardware configuration" function selectionCBD inslot +1.B2?noyesP090 = 1CBD in slot +1.B2CBD inslot +1.B3?yesnoP091 = 1P696 = 170 ... 172P697 = 120 ... 122CBD in slot +1.B3I/O Assembly for polled I/O producedconnection path.I/O Assembly for polled I/O consumedconnection path.P705 = 0 .. 2Baud rateP918 = nCBD bus address (0 < n < 63)P052 = 0Exit "hardware configuration"P695 = 0 .. 65535P053 = xP052 = 5Setting the telegram failure time in ms (0 = deactivated)Parameterizing enable CBD (refer below)Function selection"drive setting"Further information in the Section, start-up / parameterization “Expert application” of the drive InstructionManual.Fig. 5.5Parameterization “hardware configuration“36 Siemens AG 477 759 4070 76 J AA-74SIMOVERTMASTERDRIVES Betriebsanleitung/OperatingInstructions
Page 1 and 2: SIMOVERT Master DrivesCommunication
Page 3: Table of Contents5 Start-up........
Page 6 and 7: Master DrivesCBD05/20/990 Definitio
Page 8 and 9: Master DrivesCBD05/20/991 Product d
Page 10 and 11: Master DrivesCBD05/20/992 Mounting
Page 12 and 13: Master DrivesCBD05/20/993 Connectin
Page 18 and 19: Master DrivesCBD05/20/994 Data tran
Page 40 and 41: Master DrivesCBD05/20/995 Start-up5
Page 58 and 59: Master DrivesCBD05/20/996 Troublesh
Page 68 and 69: Master DrivesCBD05/20/997 Appendix7

SIMOVERT Master Drives Communication Board CBD

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?