SIMOVERT Master Drives Communication Board CBD

More documents

Recommendations

Info

Master DrivesCBD05/20/993 Connecting-up3.1 Connecting-up the bus cable3.1.1 5-pin Open Connector X4383 Connecting-upWARNINGSIMOVERT MASTER DRIVES operate at high voltages.Only qualified, trained personnel are permitted to work on the unit.Death, severe bodily injury or significant material damage could result if this is not observed.Hazardous voltages are still present in the drive up to 5 minutes after it has beendisconnected from the supply due to the DC link capacitors. Thus, before opening the drive,wait until the capacitors have been completely discharged.The power- and control terminals are at hazardous voltage levels even when the motor isstationary.The converter must always be disconnected and locked-out before work is started.If it is absolutely necessary to work with a converter opened, it should be noted that youcould come into contact with components and parts at hazardous voltage levels (shockhazard!).CAUTIONCBD contains components which can be destroyed by electrostatic discharge. Thesecomponents can be easily destroyed if incorrectly handled.Also refer to the ESD cautionary measures in the introduction section, General information3.1 Connecting-up the bus cable3.1.1 5-pin Open Connector X438Terminal Function DeviceNet Wire ColorX438.1 V- Black power supply commonX438.2 CAN- BlueX438.3 ShieldX438.4 CAN+ WhiteX438.5 V+ Red power supply +24 VDC ±1%Table 3.1Assignment of open connector X438Siemens AG 477 759 4070 76 J AA-74 9SIMOVERTMASTERDRIVES Betriebsanleitung/OperatingInstructions
Master DrivesCBD05/20/993 Connecting-up3.1 Connecting-up the bus cableAdapter BoardLEDGreenYellowRedCBD.5.4.3 .2 .1X438TOPV+CAN+ShieldCAN-V-Fig. 3.1Front view of CBD with diagnostic LEDs, terminal strip X438 and bus connenctorThe bus connector for terminal strip X438 is supplied loose. These loose components can also be individually orderedfrom Phoenix Contact or Messrs. Phoenix Contact GmbH & Co (bus connector):Order designation:Phoenix number:Combicon MSTB 2.5/5-ST-5.08-AU (cable side-sockets)Cable meeting DeviceNet specifications must be used.Thin cable: Belden 3084AThick cable: Belden 3082A or 3083A or 3085ARelation of DeviceNet Data Rate and Cable Distances:Data Trunk Distance Drop LengthRate (thick Cable) Maximum drop Cumulative125K 500m (1640 ft) 6m (20 ft) 156m (512 ft)250K 250m (820 ft) 6m (20 ft) 78m (256 ft)500K 100m (328 ft) 6m (20 ft) 39m (128 ft)NOTE: Thin cable may be used as trunk. Maximum distance is 100 meters (328 feet) for any baud rate.10 Siemens AG 477 759 4070 76 J AA-74SIMOVERTMASTERDRIVES Betriebsanleitung/OperatingInstructions
Page 1 and 2: SIMOVERT Master DrivesCommunication
Page 3: Table of Contents5 Start-up........
Page 6 and 7: Master DrivesCBD05/20/990 Definitio
Page 8 and 9: Master DrivesCBD05/20/991 Product d
Page 10 and 11: Master DrivesCBD05/20/992 Mounting
Page 14 and 15: Master DrivesCBD05/20/993 Connectin
Page 16 and 17: Master DrivesCBD05/20/993 Connectin
Page 18 and 19: Master DrivesCBD05/20/994 Data tran
Page 40 and 41: Master DrivesCBD05/20/995 Start-up5
Page 58 and 59: Master DrivesCBD05/20/996 Troublesh
Page 60 and 61: Master DrivesCBD05/20/996 Troublesh
Page 62 and 63:
Master DrivesCBD05/20/996 Troublesh
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Master DrivesCBD05/20/997 Appendix7
show all

SIMOVERT Master Drives Communication Board CBD

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?