infcr-b - Newport

More documents

Recommendations

Info

2 About The Meter2.6 DISASSEMBLYYou may need to open up the meter for one of the following reasons:• To check or change the 115 or 230 Vac power jumpers.• To install or remove jumpers on the main board.Disconnect the power supply before proceeding.To remove and access the main board, follow these steps:• Disconnect the main power from the meter.• Remove the back case cover.• Lift the back of the main board upwards and let it slide out of the case.10
3SECTION 3. GETTING STARTEDCaution: The meter has no power-on switch, so it will be in operation as soon youapply power.If you power off/on the meter, or perform a hard reset (press the RESET button twice), the metershows "RST", followed by "RTD".3.1 RATING/PRODUCT LABELThis label is located on top of the meter housing (Refer to Figure 3-4).3.2 MAIN BOARD POWER JUMPERSImportant: If you want to change the Factory preset jumpers, do the following steps;otherwise go to section 3.3.Warning: Disconnect the power from the unit before proceeding. This device mustonly be reconfigured by a specially trained electrician with correspondingqualifications. Failure to follow all instructions and warnings may result in injury!To check voltage jumpers, or to change from 115 V to 230 V ac:1. Remove the main board from the case. Refer to Section 2.6.2. Locate the solder jumpers W1, W2, and W3 (located near the edge of the main boardalongside the transformer - refer to Figure 3-1).3. If your power requirement is 115 V ac, solder jumpers W1 and W3 should be wired,but jumper W2 should not. If your power requirement is 230 V ac, solder jumper W2should be wired, but jumpers W1 and W3 should not.Figure 3-1 shows the location of solder jumpers W1 through W3 on the main board.Figure 3-1. Main Board Power Jumpers (W1, W2, W3)11
Page 3 and 4: PREFACEManual ObjectivesThis manual
Page 5 and 6: Table of Contents4.9 OUTPUT CONFIGU
Page 7: Table of ContentsNOTES, WARNINGS an
Page 10 and 11: 1 Introduction1.2 SAFETY CONSIDERAT
Page 12 and 13: 2 About The Meter2.3 AVAILABLE ACCE
Page 14 and 15: 2 About The Meter2.4 FRONT OF THE M
Page 16 and 17: 2 About The Meter2.5 REAR OF THE ME
Page 20: 3 Getting Started3.2 MAIN BOARD POW
Page 24 and 25: 3 Getting Started3.5 CONNECTING MAI
Page 27 and 28: 4SECTION 4. CONFIGURING THE METERRe
Page 29 and 30: Configuring The Meter44.5 SETPOINT
Page 31 and 32: Configuring The Meter44.8 SETPOINT
Page 33 and 34: Configuring The Meter44.10 PROPORTI
Page 35 and 36: Configuring The Meter44.12 OUTPUT S
Page 37 and 38: Configuring The Meter44.13 RTD TEMP
Page 39 and 40: Configuring The Meter44.15 BRIGHTNE
Page 41 and 42: Menu Configuration6SECTION 6. MENU
Page 43 and 44: Menu Configuration6Not all menu ite
Page 45 and 46: Menu Configuration6Table 6-3. Run M
Page 47 and 48: Specifications 8ANALOG OUTPUT (if a
Page 49 and 50: Specifications 848,0 (1.89)96,0 (3.
Page 51 and 52: CE APPROVALS INFORMATIONThis produc
Page 53 and 54: NOTES45
Page 55 and 56: Warranty/DisclaimerNEWPORT Electron

infcr-b - Newport

Create successful ePaper yourself

Delete template?

Save as template?