infcr-b - Newport

More documents

Recommendations

Info

4 Configuring The Meter4.12 OUTPUT SCALE AND OFFSET (OT.S.O) (Continued)11. Press the /DEV button. The last previously stored 4-digit number (-1999 through 9999)displays with flashing 4th digit.12. Press the /MAX button to change the value of the flashing digit. If you continue topress the /MAX button, the flashing digit's value continues to change.13. Press the /DEV button to scroll to the next digit.14. Press the MENU button to store your selection. "OUT.2" (Output 2) displays.This analog signal should correspond to your Read 2 display.15. Press the /DEV button. Selected output displays.If you select "O.2=V" for voltage, the maximum signal you may select is 10.00 for an0 to 10 V dc signal output. If you select "O.2=C" for current, the maximum signal youmay select is 19.99 for a 0 to 20 or 4 to 20 mA dc signal output.16. Press the /MAX button to change the value of the flashing digit. If you continue topress the /MAX button, the flashing digit's value continues to change.17. Press the /DEV button to scroll to the next digit.18. Press the MENU button to store your selection. The meter momentarily shows "STRD",followed also momentarily by "RST" (Hard Reset). Meter then returns you to the "RUN"mode.WARNING: If the meter displays all flashing values on any item, the value hasoverflowed. Press the /MAX button to start new values.28
Configuring The Meter44.13 RTD TEMPERATURE OFFSET (T.OFF)A new item has been added to calibrate for any offset error due to the RTD. This item will enableyou to compensate any temperature offset due to the RTD transducer:OFFSET = ACTUAL TEMPERATURE - DISPLAY TEMPERATURE1. Press the MENU button until "T.OFF" displays.2. Press the /DEV button. Previous offset value with digit 4 flashing will be displayed.3. Press the /DEV button again. Reading temperature will be displayed (with no digitflashing).4. a. If the value is okay, then press the MENU button. Display will show "STRD" and 0value will be entered at the offset.b. If the value is not okay, then enter the actual temperature using the /DEV and the/MAX buttons.5. Press the MENU button to store the changes.a. Temperature unit is either celsius or fahrenheit and will always be displayed at0.1 degree resolution. The meter flashes corresponding LED.b. MAX/MIN offset value will be ±25.0°C or 45.0°F. If offset the limit, the meter willflash "ER 3" and previous offset will not be changed.29
Page 3 and 4: PREFACEManual ObjectivesThis manual
Page 5 and 6: Table of Contents4.9 OUTPUT CONFIGU
Page 7: Table of ContentsNOTES, WARNINGS an
Page 10 and 11: 1 Introduction1.2 SAFETY CONSIDERAT
Page 12 and 13: 2 About The Meter2.3 AVAILABLE ACCE
Page 14 and 15: 2 About The Meter2.4 FRONT OF THE M
Page 16 and 17: 2 About The Meter2.5 REAR OF THE ME
Page 18 and 19: 2 About The Meter2.6 DISASSEMBLYYou
Page 20: 3 Getting Started3.2 MAIN BOARD POW
Page 24 and 25: 3 Getting Started3.5 CONNECTING MAI
Page 27 and 28: 4SECTION 4. CONFIGURING THE METERRe
Page 29 and 30: Configuring The Meter44.5 SETPOINT
Page 31 and 32: Configuring The Meter44.8 SETPOINT
Page 33 and 34: Configuring The Meter44.10 PROPORTI
Page 35: Configuring The Meter44.12 OUTPUT S
Page 39 and 40: Configuring The Meter44.15 BRIGHTNE
Page 41 and 42: Menu Configuration6SECTION 6. MENU
Page 43 and 44: Menu Configuration6Not all menu ite
Page 45 and 46: Menu Configuration6Table 6-3. Run M
Page 47 and 48: Specifications 8ANALOG OUTPUT (if a
Page 49 and 50: Specifications 848,0 (1.89)96,0 (3.
Page 51 and 52: CE APPROVALS INFORMATIONThis produc
Page 53 and 54: NOTES45
Page 55 and 56: Warranty/DisclaimerNEWPORT Electron

infcr-b - Newport

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?