T60xDFH-4 and T60xDFH-4+PIR Series Thermostat ... - Enviro-Tec

More documents

Recommendations

Info

Table 4: Installer Configuration Menu (Part 1 of 7)ParameterAppearingon DisplayDescription and Default Selection OptionsPswrdSets the protective accesspassword to prevent unauthorizedaccess to the Installer ConfigurationMenu.Default: 0Note: The default setting does notlock out access to the InstallerConfiguration Menu.BI1 Configuration of Binary Input 1.Default: NoneRange: 0 to 1,000(None): No function is associated with an input.(Rem NSB): Remote Night Setback (NSB) via a time clock input, anoccupancy sensor, or from a voltage-free contact.Contact open = Occupied; contact closed = Unoccupied.(MotionNO*): Temporary occupancy request via a motion detectorinput. Contact open = Unoccupied. When the contact closes, thethermostat controller goes into the Occupied mode for a specifiedTOccTime. Once the TOccTime begins, the thermostat controllerremains in the Occupied mode if the contact is open, until theTOccTime expires. Advanced PIR occupancy functions using aNormally Open (N.O.) or Normally Closed (N.C.) remote PIR motionsensor.(MotionNC*): Temporary occupancy request via a motion detectorinput. Contact closed = Unoccupied. When the contact opens, thethermostat controller goes into the Occupied mode for a specifiedTOccTime. Once the TOccTime begins, the thermostat controllerremains in the Occupied mode if the contact is closed, until theTOccTime expires. Advanced PIR occupancy functions using aNormally Open (N.O.) or Normally Closed (N.C.) remote PIR motionsensor.(Window): Cancels the thermostat controller heating or coolingaction when a window is open. The fan operation is only affected ifthe Fan Menu parameter is set to (4): On-Auto, and Auto is theselected fan mode. A Window alarm is displayed indicating that thewindow needs to be closed to resume heating or cooling. Theheating and/or cooling outputs are enabled only when the contact isclosed.* These settings disable any local override function. For PIRmodels, see the Occupancy Sensor Operation – T60xDFH-4+PIRSeries Thermostat Controllers section.14T60xDFH-4 and T60xDFH-4+PIR Series Thermostat Controllers with Dehumidification and OccupancySensing Capability Installation Instructions
Table 4: Installer Configuration Menu (Part 2 of 7)ParameterAppearingon DisplayDescription and Default Selection OptionsBI2 Configuration of Binary Input 2.Default: NoneUI3 Configuration of Universal Input 3.Default: NoneMenuScroAutoMode%RH dispGives the option of having thedisplay continuously scroll theparameters.Default: onEnables the auto function (ifOption 2 is chosen in the SeqOperaparameter) to be visible within theMODE key menu. (The MODE keyis the key at the far left of thethermostat controller cover.)Default: offDisplays the current humidityreading (T603 and T605 models).Default: off(None): No function is associated with an input.(Door Dry): Door contact only has an effect if BI1 is set toMotionNO or MotionNC or if a PIR accessory cover is used. (Seethe BI1 parameter earlier in this table.) The occupancy is nowdictated via BI1, BI2, or PIR. Any motion detected sets the zone toOccupied status. The thermostat controller remains in the Occupiedmode until the door contact switch opens momentarily, at whichpoint the thermostat controller goes into Stand-By mode. If moremovements are detected, the Occupied mode resumes. While thedoor is open, any movements detected by the PIR sensor areignored. Use a Normally Closed (N.C.) switching device. (Contactopen = door open; contact closed = door closed.)(RemOVR): Temporary occupancy request via a remote input. Thisoverride function is controlled by a manual remote occupancyoverride. When enabled, this condition disables the overridecapability of the thermostat controller.(Filter): A Filter alarm is displayed. This alarm can be connected toa differential pressure switch that monitors a filter.(Service): A Service alarm is displayed on the thermostat controllerwhen the input is energized. This input can be tied into the airconditioning unit control card, which provides an alarm should therebe a malfunction.(None): No function is associated with an input.(COC/NH): Changeover Contact/Normally Heat: A dry contact inputis used to signal seasonal hot/cold water changeover. The contactcloses when cold water is present. Valid only for two-pipe systems.(COC/NC): Changeover Contact/Normally Cool: A dry contact inputis used to signal seasonal hot/cold water changeover. The contactcloses when hot water is present. Valid only for two-pipe systems.(COS): Changeover Analog Sensor: Used for hot/cold waterchangeover switching. Valid only for two-pipe systems. (ParameterPipe No is set to 2.0.) If the water temperature is greater than75°F/24°C, hot water is present. If the water temperature is lessthan 75°F/24°C, cold water is present.Note: Choose the selection option (0): Cooling Only for theSeqOpera parameter to allow changeover to occur betweenCooling Only and Heating Only. The changeover sensor does notoperate in Cooling and Reheat, Heating and Reheat, orCool/Heat Four-Pipe and Reheat applications.(SS): Supply Air Sensor Monitoring(off): The scroll is inactive.(on): The scroll is active.(on): The auto function is active (Off-Auto-Heat-Cool). Providesautomatic changeover between heating and cooling.(off): The auto function is inactive (Off-Heat-Cool).(on): Displays the current humidity reading in % RH.(off): Does not display the current humidity reading.T60xDFH-4 and T60xDFH-4+PIR Series Thermostat Controllers with Dehumidification and OccupancySensing Capability Installation Instructions15
Page 4 and 5: Table 1: Terminal Identification (S
Page 6 and 7: BO224 V~Hot24 V~ComN.C.CoolingValve
Page 8 and 9: Status Display MenuThe Status Displ
Page 10 and 11: OccupiedStand-By= 2 HrsStand-By= 2
Page 12 and 13: Cooling SetpointOnDevice OpenedOnRe
Page 16 and 17: Table 4: Installer Configuration Me

T60xDFH-4 and T60xDFH-4+PIR Series Thermostat ... - Enviro-Tec

Create successful ePaper yourself

Delete template?

Save as template?