3-phase TEFV induction motors ATEX GAS - Zones 1 & 2
3-phase TEFV induction motors ATEX GAS - Zones 1 & 2
3-phase TEFV induction motors ATEX GAS - Zones 1 & 2
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
C5.1 - LUBRICATION OF<br />
BEARINGS<br />
C5.1.1 - Permanently greased<br />
bearings<br />
For <strong>motors</strong> of frame size ≤ 132 mm, the<br />
type and size of the bearings make for long<br />
grease life and therefore lubrication for the<br />
lifetime of the machine.<br />
The grease life L according to speed of<br />
10h<br />
rotation and ambient temperature is shown<br />
on the chart opposite.<br />
C5.1.2 - Bearings without grease<br />
nipples only for LSE and LSN<br />
LSE and LSN <strong>motors</strong> of frame size 160 to<br />
200 are supplied as standard without grease<br />
nipples but with permanently greased<br />
bearings.<br />
Lubricant lifetime (L10h) under normal<br />
operating conditions is given in the table<br />
below for a machine with horizontal shaft<br />
operating at 50 Hz and 60 Hz in ambient<br />
temperatures of 25°C or less.<br />
C5.1.3 - Bearings with grease<br />
nipples<br />
FLSD and FLSN <strong>motors</strong> of frame size ≥ 160<br />
mm and also LSE/LSN <strong>motors</strong> size ≥ 225<br />
mm are fitted with grease nipples. The table<br />
in section 5.1.3.1 (on the next page)<br />
indicates the type of ball bearing, the quantity<br />
of grease and the regreasing intervals<br />
according to the type of motor, for an ambient<br />
temperature of 25°C.<br />
For vertical shaft machines used in an<br />
ambient temperature of 25°C, the regreasing<br />
intervals will be approximately 80% of the<br />
values stated.<br />
3-<strong>phase</strong> <strong>TEFV</strong> <strong>induction</strong> <strong>motors</strong><br />
<strong>ATEX</strong> <strong>GAS</strong> - <strong>Zones</strong> 1 & 2<br />
Construction<br />
C5 - Bearings and lubrication<br />
t Grease life L10h in 000’s of hours, for frame sizes ≤ 132<br />
t Lubricant lifetime<br />
Frame size<br />
T amb (°C)<br />
60<br />
50<br />
40<br />
30<br />
20<br />
10<br />
0<br />
Speed<br />
N = 750 min -1<br />
N = 1000 min -1<br />
N = 1500 min -1<br />
N = 3000 min -1<br />
5 10 15 20 25<br />
Life L10h in 000’s of hours<br />
3600 3000 1800 1500<br />
160 ≥ 40,000 ≥ 40,000 ≥ 40,000 ≥ 40,000<br />
180 ≥ 40,000 ≥ 40,000 ≥ 40,000 ≥ 40,000<br />
200 16,000 24,000 32,000 ≥ 40,000<br />
Note: On request, <strong>motors</strong> of frame size 90 to 200 mm can be fitted with grease nipples, and<br />
<strong>motors</strong> of frame size 225 and 250 can be supplied without grease nipples.<br />
Motors operating in an ambient temperature<br />
of 40°C need more frequent lubrication. The<br />
regreasing intervals will be around 50% of<br />
the values stated (in all cases, comply with<br />
the requirements on the motor nameplates).<br />
Grease references: see instructions on<br />
nameplate.<br />
30<br />
The table on the next page is valid<br />
for LS <strong>motors</strong> lubricated with ESSO<br />
UNIREX N3 grease, which is used as<br />
standard, and also KLUBER BQ72-72<br />
grease for FLSD and FLSN 315 ST/M/L<br />
and 355 L, 2-pole versions only.<br />
25