MDC Manual 1109KB - Red Lion Controls

More documents

Recommendations

Info

PROGRAMMING GENERAL DESCRIPTION Programming is done through the front panel keypad, which allows the user to enter into Main Menus, Sub-Menus, and Edit Menus. English language prompts, flashing parameter values, and the front panel keypad aid the operator during programming. Although the unit has been programmed at the factory, the parameters generally have to be changed to suit the desired application. From the Indication Display Module, the Programming Module is entered by pressing the Program/Enter (PGM/ENT) key. This displays “PROGRAM MODE”. Then press the Select (SEL) key to enter the Programming Module. The Up and Down arrows are used to scroll through the main menus. Pressing Select (SEL) from a main menu, allows the user to enter a Sub-Menu where parameter values can be viewed. Parameter values are changed and entered in the Edit Menu. There are two types of Edit Menus: 1. A Choice Edit Menu allows the operator to scroll through options by pressing the down arrow key until the desired option is viewed. The option is entered by pressing the PGM/ENT (enter) key, which returns the operator to the previous sub-menu. The operator can exit the Edit Menu WITHOUT making a selection by pressing the
USER SETPOINTS MODULE The User Setpoints Module is accessed from any of the Indication Displays, or from any of the main menus in the Programming Module (except Operating Mode Menu), by pressing the SET key. Pressing “SET” once enters the Setpoint Scroll Menu. In this menu, the current speed or ratio setpoint may be incremented or decremented using the Up and Down arrow keys. The top line of the display shows the current setpoint value and the bottom line shows actual speed in display units. Pressing “SET” a second time enters the User Setpoints Menu. The top line shows the Setpoint description and the bottom line shows the Setpoint value. The up and down arrow keys may be used to scroll through the loop. Pressing the SEL key allows the value to be changed in a Value Edit Menu. Press ESC to exit the User Setpoints Module. The following flowchart shows only the User Setpoints portion: � Note: These maximums are additionally limited by unit scaling. See individual descriptions for details. -13-
Page 1 and 2: THE MOTOR DRIVE CONTROLLER MODEL MD
Page 3 and 4: TABLE OF CONTENTS I. GENERAL DESCRI
Page 5 and 6: TABLE OF CONTENTS (Cont’d) IV. PR
Page 7 and 8: QUICK START - SETTING UP THE MDC Wh
Page 9 and 10: THEORY OF OPERATION In Master Mode,
Page 11 and 12: KEYPAD DESCRIPTION Shown here is a
Page 13: OVERFLOW INDICATION An input freque
Page 17 and 18: USER SETPOINTS IN FOLLOWER MODE The
Page 19 and 20: PROGRAM SCALING MENU The Program Sc
Page 21 and 22: PROGRAM USER MENU There are four ex
Page 23 and 24: SETPOINT INCREMENT (INC SPT) Only a
Page 25 and 26: Phase The positive (+) phase of an
Page 27 and 28: -25-
Page 29 and 30: USER SETTINGS This Menu should only
Page 31 and 32: PROGRAM DIAGNOSTICS MENU This Menu
Page 33 and 34: INSTALLATION & CONNECTIONS Installa
Page 35 and 36: WIRING CONNECTIONS When wiring the
Page 37 and 38: DEDICATED FUNCTION AND USER INPUTS
Page 39 and 40: VARIOUS SENSOR OUTPUT CONNECTIONS (
Page 41 and 42: ISOLATED DRIVE OUTPUT CALIBRATION N
Page 43 and 44: 11. CONTROL INPUTS: Internal 10 K
Page 45 and 46: TROUBLESHOOTING GUIDE (Cont’d) PR
Page 47 and 48: APPENDIX “A” APPLICATIONS -45-
Page 49 and 50: APPENDIX “B” - ORDERING INFORMA
Page 51: Red Lion Controls 20 Willow Springs

MDC Manual 1109KB - Red Lion Controls

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?