REGO-FIX Main Catalogue ENGLISH

More documents

Info

Assembly instructions for ER and MR collets Collets ER 11 – ER 50 and MR 11 – MR 32 (with collet locking system) Assembling Insert groove of the collet into eccentric ring of the clamping nut at the mark on the bottom of the nut. Push collet in the direction of the arrow until it clicks in. Insert tool. Screw nut with collet onto toolholder. Assembling Collet groove Eccentric ring Mark on bottom Disassembling After the nut is unscrewed from the toolholder, press on the face of the collet while simultaneously pushing sideways on the back of the collet opposite the mark until it disengages from the clamping nut. Important Improper assembly can permanently damage the runout TIR of the collet and may result in the destruction of the clamping nut. Only mount nuts with correctly inserted collets. Never place the collet into the holder without first assembling into the nut. Disassembling Mark on bottom Collets ER 8 (without collet locking system) Assembling Insert groove of the collet into eccentric ring of the clamping nut at the mark on the bottom of the nut. Insert tool. Hold nut with collet in horizontal position and screw onto toolholder. Important The face of the ER 8 collet chuck must fit cleanly against the inner surface of the clamping nut. (ER 8 collets do not feature a 30° cone.) Collet groove Face contact Disassembling After unscrewing the clamping nut from the tool holder, the collet can easily be removed from the clamping nut. Eccentric ring Mark on bottom Expert advice Never insert the tool less than 2 / 3 of the collet length. We recommend tightening the clamping nuts with our TORCO-BLOCK or torque wrench. For more information on TORCO-BLOCK, see page 262. For tightening torque recommendations, please refer to page 293. 290 Technical information
Instructions for correct clamping of tool shanks Note // ER collet chucks – Exception: Toolholders with cylindrical shanks – are supplied without stop screws // Stop screws are supplied upon request // If ordering stop screw, specifying part no. (XXXX.XXXXX) and LOT no. (YYY). YYY of the toolholder is mandatory Advice // Stop screws are used to secure tool shanks against axial displacement and may not be used as length adjustment screws // For trouble-free operation of the ER collet system, clamp tool shank first, then set stop screw // Incorrect handling of the stop screw may reduce runout accuracy and clamping force of the collet system // The use of stop screws may increase imbalance of the collet system Set tool length with clearance to the stop screw, then clamp tool. Apply stop screw to tool shank. Technical information 291
Page 4 and 5:
High-performance toolholding from t
Page 6 and 7:
Your application is our motivation
Page 9 and 10:
PG-MB PG PG-CF PG-L PG-S PG-T PG-SG
Page 11 and 12:
Automatic clamping unit PGU Toolhol
Page 13 and 14:
Manual clamping unit PGC 2506 Clamp
Page 15 and 16:
powRgrip ® toolholders in Swiss qu
Page 17 and 18:
HSK-A toolholders HSK-A DIN 69893 I
Page 19 and 20:
HSK-A toolholders Dimensions [mm] H
Page 21 and 22:
HSK-F toolholders HSK-F DIN 69893 I
Page 23 and 24:
SK toolholders SK DIN 69871 DIN ISO
Page 25 and 26:
SK toolholders SK-B toolholders SK
Page 27 and 28:
SK+ toolholder SK+ DIN 69871 DIN IS
Page 29 and 30:
BT toolholders BT MAS 403 JIS B 633
Page 31 and 32:
Page 33 and 34:
powRgrip ®
Page 35 and 36:
REGO-FIX BT+ dual contact toolholde
Page 37 and 38:
CAT toolholders CAT CAT-B ASME B5.5
Page 39 and 40:
CAT+ toolholders REGO-FIX CAT+ dual
Page 41 and 42:
REGO-FIX CAPTO toolholders licensed
Page 43 and 44:
D ISO 20 interface ISO 20 toolholde
Page 45 and 46:
CYL toolholders CYL-T toolholders (
Page 47 and 48:
secuRgrip ® toolholders PG-SG PG-S
Page 49 and 50:
Heavy Duty secuRgrip ® Toolholders
Page 51 and 52:
D PG tapping holders HSK-A SSY CYL
Page 53 and 54:
powRgrip ® collets in Swiss qualit
Page 55 and 56:
PG standard collets PG Std. powRgri
Page 57 and 58:
PG standard collets PG Std. powRgri
Page 59 and 60:
Coolant flush collets PG-CF PG-CF p
Page 61 and 62:
Long shank collets PG-L PG-L powRgr
Page 63 and 64:
Short shank collets PG-S PG-S powRg
Page 65 and 66:
secuRgrip ® collets PG-SG PG-SG po
Page 67:
powRgrip ®
Page 70 and 71:
Standard Colletholders for tapping
Page 72 and 73:
Cylindrical colletholders CYL/ ER C
Page 74 and 75:
HSK interface HSK toolholders Desig
Page 76 and 77:
HSK-A toolholders HSK-A DIN 69893 I
Page 78 and 79:
HSK-E toolholders HSK-F toolholders
Page 80 and 81:
SK interface Steep taper toolholder
Page 82 and 83:
SK-B toolholders SK-B DIN 69871 DIN
Page 84 and 85:
BT interface Steep taper toolholder
Page 86 and 87:
BT toolholders ERA Zero-Z ® toolho
Page 88 and 89:
BT-B toolholders BT-B Dimensions [m
Page 90 and 91:
BT+ interface REGO-FIX BT+ toolhold
Page 92 and 93:
CAT interface Steep taper toolholde
Page 94 and 95:
CAT-B toolholders CAT-B Dimensions
Page 96 and 97:
CAT+ interface REGO-FIX CAT+ toolho
Page 98 and 99:
REGO-FIX CAPTO interface REGO-FIX C
Page 100 and 101:
REGO-FIX CAPTO toolholders licensed
Page 102 and 103:
Cylindrical (CYL) interface Cylindr
Page 104 and 105:
CYL / ER toolholder CYL Dimensions
Page 106 and 107:
CYL / ERM toolholders (mini clampin
Page 108 and 109:
CYLF / ERM toolholders (mini clampi
Page 110 and 111:
CYLF / ERM toolholders (mini clampi
Page 112 and 113:
CYDF / ERM toolholders (mini clampi
Page 114 and 115:
MK interface Morse taper toolholder
Page 116 and 117:
SH interface Automotive shank toolh
Page 118 and 119:
D ISO 20 interface ISO 20 toolholde
Page 120 and 121:
ER tapping holders ER thread-cuttin
Page 122 and 123:
ER floating chucks ER floating chuc
Page 124 and 125:
PHC floating chucks for coolant thr
Page 126 and 127:
MPH mini floating chucks with intRl
Page 128 and 129:
Maintenance instructions for floati
Page 130 and 131:
Collet reductions Collet reductions
Page 132 and 133:
Collet reductions with intRlox ® (
Page 134 and 135:
swissQuick powRgrip ® adapter What
Page 136 and 137:
Micromachining Standard and ultrapr
Page 138 and 139:
Microbore collets ER-MB ER-MB Clamp
Page 140 and 141:
ER standard collets and ultraprecis
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Metallic sealed collets ER-DM ER-DM
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
ER-GB ER tapping collets ER-GB Manu
Page 156 and 157:
ER tapping collets ER-GB ER-GB [inc
Page 158 and 159:
PCM ET1 ER tapping collets PCM ET1
Page 160 and 161:
ER tapping collets PCM ET1 PCM ET1
Page 162 and 163:
Standard Standard with bearing Mini
Page 164 and 165:
C Hi-Q ® ER / ER standard Hi-Q ®
Page 166 and 167:
C Hi-Q ® ER / ERC Hi-Q ® / ERC fo
Page 168 and 169:
Hi-Q ® ERB / ERBC Hi-Q ® / ERB fr
Page 170 and 171:
C Hi-Q ® ERM / ERMC Hi-Q ® / ERM
Page 172 and 173:
C Hi-Q ® ERMX / ERMXC intRlox ® H
Page 174 and 175:
C ER MS ER MS clamping nuts for hig
Page 176 and 177:
Hi-Q ® ERAX / ERAXC Hi-Q ® / ERAX
Page 178 and 179:
eCool ® RCS Fast and easy retrofit
Page 180 and 181:
eCool ® RCR Low-cost retrofitting
Page 182 and 183:
eCool ® accessories Matching acces
Page 184 and 185:
Use conditions RCR reCool ® reCool
Page 187 and 188:
MR product offering Experience high
Page 189 and 190:
Toolholders in Swiss quality Norm D
Page 191 and 192:
D HSK-A toolholders HSK-A DIN 69893
Page 193 and 194:
micRun ®
Page 195 and 196:
SK toolholders SK DIN 69871 DIN ISO
Page 197 and 198:
Page 199 and 200:
CAT toolholders CAT ASME B5.50 Dime
Page 201 and 202:
CYL toolholders CYL Dimensions [mm]
Page 203 and 204:
Swiss quality MR collets MR collets
Page 205 and 206:
MR collets MR collets Ø Type Part
Page 207 and 208:
Grooveless MR nuts for high-end mac
Page 209 and 210:
Multi Line product offering Experie
Page 211 and 212:
Toolholders and adapters WD MA KFD
Page 213 and 214:
Weldon end mill holders HSK-A / WD
Page 215 and 216:
Universal shell / face mill holders
Page 217 and 218:
Drill chucks HSK-A / KBF HSK-A/KBF
Page 219 and 220:
Multi Line
Page 221 and 222:
Weldon end mill holders SK / WD SK
Page 223 and 224:
Drill chucks SK / KBF SK / KBF DIN
Page 225 and 226:
d BT / WD Weldon end mill holders B
Page 227 and 228:
Universal shell / face mill holders
Page 229 and 230:
Morse taper holders BT / MK BT / MK
Page 231 and 232:
d D d D REGO-FIX CAPTO holders lice
Page 233 and 234:
D REGO-FIX CAPTO holders licensed b
Page 235 and 236:
Multi Line
Page 237 and 238:
Reduction sleeves for hydro chucks
Page 239 and 240:
Reduction sleeves HS [inch] HS Ø b
Page 241 and 242:
1.1.3 1.1.2 Accessories 1.1.1 powRg
Page 244 and 245: powRgrip ® length-presetting tool
Page 246 and 247: Sealing disks DS Effective solution
Page 248 and 249: Sealing disks for ER / MR DS / ER D
Page 250 and 251: Sealing disks for ER / MR DS / ER D
Page 252: Sealing disks for ER DS / ER Tool d
Page 255 and 256: Coolant flush disks for ER / MR KS
Page 257 and 258: Coolant flush disks for ER / MR KS
Page 259 and 260: Wrenches E MS E AX E A Suited wrenc
Page 261 and 262: Wrench heads A-E A-E P A-E M A-E MX
Page 263 and 264: Slip-off proof extension V-E AX for
Page 265 and 266: Mobile workbench for PGU 9500 Descr
Page 267 and 268: TORCO-BLOCK and components Type Par
Page 269 and 270: Coolant tubes KSR Wrenches for cool
Page 271 and 272: Technical information Discover powR
Page 273 and 274: Increased cutter tool life with the
Page 275 and 276: Successful clamping since 1972 Comb
Page 278 and 279: XL vibration damping Optimize your
Page 280 and 281: Form-fit for 100 % pullout protecti
Page 282 and 283: Mastering both wet and dry applicat
Page 284 and 285: Cryogen: Coolant at the right spot
Page 286: powRgrip ® System and secuRgrip ®
Page 289 and 290: Presetting range of powRgrip ® col
Page 293: The unbeatable advantages from the
Page 297 and 298: Recommended tightening torque for E
Page 299 and 300: 8° ER collets dimensions Size [mm]
Page 302 and 303: Dimensions for ER collet cavities i
Page 304 and 305: Technical information for tapping c
Page 306 and 307: Reduction sleeves HS Measurements [
Page 308 and 309: Spindle interface norms HSK SK BT C
Page 310: HSK interface HSK DIN 69893 ISO 121
Page 313 and 314: weight removed axis of gravity axis
Page 315 and 316: Balancing quality In recent years t
Page 317 and 318: Balancing at REGO-FIX All toolholde
Page 319 and 320: Interpreting the DIN 69888:2008-09
Page 321 and 322: designed specifically for this purp
Page 323 and 324: Troubleshooting when drilling Possi
Page 325 and 326: Troubleshooting when tapping Possib
Page 327 and 328: Cutting speed conversion table for
Page 329 and 330: Conversion table / inch-metric 0“
Page 331 and 332: Position tolerances according to DI
Page 334 and 335: Tolerance charts Outside dimensions
Page 336 and 337: Core hole diameters for thread cutt
Page 338 and 339: Core hole diameters for thread cutt
Page 340 and 341: Shank diameter of taps Thread ISO 5
Page 342 and 343: Material No. DIN AFNOR BS GOST USA
Page 344 and 345:
Material No. DIN AFNOR BS GOST USA
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Terminology M - Z M MA Shell Mill A
Page 360:
www.rego-fix.com 0362.00251 / ENG.1
show all

REGO-FIX Main Catalogue ENGLISH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?