SIGMA 8000, 8000 Plus and 8002 Plus Infusion Pump Operator's ...

More documents

Recommendations

Info

Example: Option 60 – Auto Program Mode 29 Rev. J
30 Rev. J Options 60 OPT. NO OPTION NAME INSTRUCTIONS DISPLAY In AUTOMATIC PROGRAMMING MODE (also Called ‘ramping/tapering’), entry of a single VOLUME LIMIT (ml) and infusion TIME (hrs.) results in the pump computing a 21 step; ramp up (10 steps), MAIN RATE (1 step), and taper down (10 steps) program. The program ends with a PROG COMP (program complete) alarm and KVO rate. The ramp and taper each take10% of total time, leaving 80% of total time for the MAIN RATE. The ramp and taper are broken into 10 steps each, with the first ramp step RATE beginning at 50% of the MAIN RATE. Each succeeding step results in a RATE increase equivalent to 5% of the MAIN RATE. The taper mirrors the ramp, but with descending RATES. See the graph on page29 for a programming example. The pump may be programmed with or without an IV set loaded. Program entries are maintained in permanent memory and may be cleared by: pushing OPTIONS, the desired OPT. number, and then pressing CLEAR, or by using OPTION 95 - Clear all Program Modes. These actions cause a return to primary mode (PRI MODE) If a pump is turned off in the middle of a program and is left off for more than 60 min., it will automatically reset to step 1. If it is turned TIME OUT back on in less than 60 mins, it remains at the step in which it was OPT 60/AUTO PROG/STEP XX/IN turned off. STOP/PUSH RUN PROGRAMMING AUTOMATIC Stop the pump. Push OPTIONS. IN STOP/PUSH RUN SET/OPT CODE- 60 (21 STEPS) (Not available on all models) Select 60. Push ENTER. Select the total VOLUME LIMIT in ml. For example, select 2000 ml. Push ENTER OPT 60/AUTO PROG/PUSH ENTR- SET PROG/VOL 0 VOL 2000/PUSH ENTR SET PROG/0 hrs Select the total infusion TIME in hrs. For example, select 10 hrs. 10 hrs/PUSH ENTR Push ENTER Push RUN to begin the infusion. To review actual RATES and VOL. LIMITS for each individual step, repeatedly push the RATE or VOL. LIMIT keys with pump stopped To exit OPTION 60 and immediately begin the taper steps, simply enter OPTION 61 OPT 60/AUTO PROG/STEP1/IN STOP/ PUSH RUN
Page 1 and 2: SIGMA 8000, 8000 Plus Plus and 8002
Page 3 and 4: INTRODUCTION: Introduction & Intend
Page 5 and 6: Views FRONT VIEW - 8000 Single Chan
Page 7 and 8: SUMMARY: Loading Sets & Start Up 1.
Page 9 and 10: Start-Up with Drug Error Prevention
Page 11 and 12: SUMMARY: Unloading Sets 1. With pow
Page 13 and 14: 7. To silence the audio alarm for 2
Page 15 and 16: unload and reload the set from the
Page 17 and 18: * PRI FLOW: The Flow Sensor has det
Page 19 and 20: Option Modes SUMMARY: 1. Push STOP.
Page 21 and 22: Options 10, 11, 12 OPT. NO. 20 Rev.
Page 23 and 24: 22 Rev. J Options 21 OPT. NO 21 OPT
Page 25 and 26: 24 Rev. J Options 40, 41, 42, 43, 4
Page 27 and 28: Options 50 (cont’d), 51, 52 26 Re
Page 29: Options 53, 54, 55, 56, 57 28 Rev.
Page 33 and 34: Options 63, 64, 70 32 Rev. J OPT. N
Page 35 and 36: Options 80 OPT. NO. 34 Rev. J OPTIO
Page 37 and 38: Options 81, 90 OPT. NO. 36 Rev. J 8
Page 39 and 40: Display Abbreviations Abbreviation
Page 41 and 42: Drug Abbreviation Drug Abbreviation
Page 43 and 44: CLEANING: Cleaning & Storing 1. Tur
Page 45 and 46: Cautions 1. Operation of this pump
Page 47 and 48: 22. The following precautions are s
Page 49 and 50: Accessories: Accessories and SIGMA
Page 51 and 52: RS232 (Pump to Computer Interface)
Page 53 and 54: Specifications *Applications: 1. La
Page 55 and 56: Distance Occlusion Above Pump RATE
Page 57 and 58: * RS232 Communication Port. * Alarm
Page 59: SHALL NOT BE DEEMED TO CREATE AN EX

SIGMA 8000, 8000 Plus and 8002 Plus Infusion Pump Operator's ...

Create successful ePaper yourself

Delete template?

Save as template?