ENVI PRO OPERATION MANUAL - Scintrex

More documents

Recommendations

Info

Operating Displays NORTHING Instrument setup display 5—3 The GPS easting of this measurement in UTM coordinate. It consists of the positive numeric part (nnnnnnn.n). This display enables you to configure the basic data acquisition portion of the ENVI PRO and is accessible with the “SETUP” key. ENVI PRO instrument setup display Parameter Description Default MAG SETUP AUTO ST. INC. CYCLE REPEAT Displays the magnetometer specific setup menu. Pressing the “ENTER” key gets the next menu. A “yes/no” toggle that controls the automatic station increment (decrement). no - for the base station, walking or manual type of operation. yes – for semi-automatic operation. Determines whether the magnetometer will take one reading only, or will continuously take readings at the time interval specified by the DURATION parameter I the Mag. Setup. This is not applicable for Base Station operation, which is set in the Mag Setup. No No P/N 788715 Rev. 0
Operating Displays CYCLE DELAY ERASE MEMORY HEATER 5—4 The delay between readings when the cycle repeat feature is enabled. It affects the total-field magnetometer or gradiometer only. The base-station repetition rate is controlled in the Mag. Setup under Cycle Time. Allows clearing of the data memory. A request for confirmation will be displayed before the actual erasure takes place. NOTE: The setup parameters remain intact. Enables or disables the LCD display heater. If the temperature is above – 15° C, enabling this parameter has no effect. Magnetometer setup display This display is different depending on if GPS is enabled or not. This display provides access to the parameters affecting the operation of the magnetometer portion of the ENVI. This display is accessible from either the Instrument setup display, or from the Main operating display (by using the short-cut, i.e. pressing the “ENTER” key). 0 No No P/N 788715 Rev. 0
Page 1 and 2: ENVI PRO OPERATION MANUAL
Page 3 and 4: 3 SCINTREX LIMITED 222 Snidercroft
Page 5 and 6: Access the Main Operating Display .
Page 7 and 8: 4 Bibliography ....................
Page 9 and 10: 3. Low temperature operations - An
Page 11 and 12: Introduction also enter descriptive
Page 13 and 14: Unpacking The standard ENVI PRO is
Page 15 and 16: Preparing 4. Remove the cable hold-
Page 17 and 18: Preparing 2. Insert the GPS antenna
Page 19 and 20: Preparing Back-pack Installation A
Page 21 and 22: Preparing 3—10 Complete Assembly
Page 23 and 24: Preparing 7. Please check the batte
Page 25 and 26: 4—1 Chapter 4 The Instrument This
Page 27 and 28: Console The keypad has 19 keys. Two
Page 29 and 30: Console 4—5 *Manually records mea
Page 31 and 32: Console 4—7 Instrument display sh
Page 33 and 34: Operating Displays 4—0 P/N 788715
Page 35: Operating Displays The configurable
Page 39 and 40: Operating Displays TUNE FIELD BASE
Page 41 and 42: Operating Displays TIE MODE AUTO RE
Page 43 and 44: Operating Displays 5—10 Page 1 of
Page 45 and 46: Operating Displays 5—12 * You wil
Page 47 and 48: Operating Displays 5—14 The RECAL
Page 49 and 50: Operating Displays 5—16 The RECAL
Page 51 and 52: Operating Displays 5—18 The data
Page 53 and 54: Operating Displays Macros (pre-reco
Page 55 and 56: Operating Displays 5—22 Fig. 5 Th
Page 57 and 58: 6—1 Chapter 6 Setting Up the ENVI
Page 59 and 60: Setting Up HOW TO: 6—3 Main opera
Page 61 and 62: Setting Up 6—5 2 3 Line and Stati
Page 63 and 64: Setting Up 6—7 Enter e (for east)
Page 65 and 66: Setting Up 6—9 Press the “SETUP
Page 67 and 68: Setting Up 6—11 Move the cursor t
Page 69 and 70: Setting Up 6—13 Move the cursor t
Page 71 and 72: Setting Up 6—15 Follow the instru
Page 73 and 74: Setting Up Information Display 6—
Page 75 and 76: Setting Up Note Entry 6—19 perman
Page 77 and 78: Setting Up Display Intensity Contro
Page 79 and 80: Setting Up 6—23 P/N 788715 Rev. 0
Page 81 and 82: Operating Also, the closer a sensor
Page 83 and 84: Operating Magnetometer Operation Wa
Page 85 and 86: Operating 7—6 Move the cursor to
Page 87 and 88:
Operating 7—8 Typical gradiometer
Page 89 and 90:
Operating 7—10 any unique note af
Page 91 and 92:
Operating Check your setup 7—12 W
Page 93 and 94:
Operating To correct your data, pro
Page 95 and 96:
Operating Line type - collecting da
Page 97 and 98:
Operating 7—18 Tie-line method fo
Page 99 and 100:
8—1 Chapter 8 Data Output Note: F
Page 101 and 102:
Data Output The following is the XY
Page 103 and 104:
Data Output Operation Mode From the
Page 105 and 106:
Data Output Specific data 8—7 Pre
Page 107 and 108:
Data Output 8—9 Hint: Operation m
Page 109 and 110:
9—1 Chapter 9 Maintenance and Rep
Page 111 and 112:
Maintenance & Repair 9—3 Location
Page 113 and 114:
Maintenance & Repair The cable conn
Page 115 and 116:
10—1 Chapter 10 Reference Informa
Page 117 and 118:
Reference Information Staff: 25 mm
Page 119 and 120:
11—1 Chapter 11 Applications for
Page 121 and 122:
Applications Anomalies 11—3 The E
Page 123 and 124:
Applications magnetizable bodies ca
Page 125 and 126:
Applications 11—7 Variation of pr
Page 127 and 128:
Applications The following table gi
Page 129 and 130:
Applications The remnant magnetic c
Page 131 and 132:
Applications expected width of the
Page 133 and 134:
Applications meter (or about every
Page 135 and 136:
Applications Survey procedures and
Page 137 and 138:
Applications As illustrated above,
Page 139 and 140:
Applications 11—21 Typical tie-po
Page 141 and 142:
Applications 11—23 Typical herrin
Page 143 and 144:
Applications presentation of the da
Page 145 and 146:
1 Bibliography Benson, R., Glaccum,
Page 147 and 148:
Data Displays Advanced Mode, 5—8
Page 149:
5 U Unpacking, 3—2 Upgrades & Opt
show all

ENVI PRO OPERATION MANUAL - Scintrex

Create successful ePaper yourself

Delete template?

Save as template?