211-125A Table Assembly - Atlanta Attachment Co.
211-125A Table Assembly - Atlanta Attachment Co.
211-125A Table Assembly - Atlanta Attachment Co.
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Suggested Sewing Guidelines<br />
For Rimoldi<br />
1. Positioning Of The Needles (fig.1)<br />
The machine has been tuned with<br />
RIM needles. The needles are in<br />
the correct position on the<br />
horizontal plane when, with their<br />
points inserted in the needle plate,<br />
they are centered with the eyelet.<br />
The needles are in the correct<br />
position on the vertical plane when<br />
distance “a” between the point of<br />
the needle in its uppermost<br />
position and the plane of the<br />
needle plate is as shown in the<br />
phasing table which comes with<br />
the head. To adjust, loosen screw<br />
A on clamp B and adjust it. Next<br />
tighten the clamp screws, making<br />
sure that it is pushed up home<br />
against the needle bar. Adjust pin<br />
C so that it touches the needle<br />
holding clamp and then lock it with<br />
screw E. Tighten up clamp screw<br />
A on clamp . Distance “a” on the<br />
interlock stitch machine should be<br />
measured considering the right<br />
needle. Screw down the clamp<br />
screw tightly. The distance “a”<br />
must fall between the point of the<br />
right hand needle and the surface<br />
of the needle plate.<br />
2. Positioning The Presser-foot And<br />
Setting Presser Spring Regulator<br />
(Fig. 2)<br />
The presser-foot is in the correct<br />
position when the needles pass<br />
through the center of the slots in<br />
the presser-foot. The needles can<br />
be centered by loosening screw C<br />
which blocks the presser foot at<br />
the bar Remember that with the<br />
presser-foot raised about 4.5 mm.<br />
above the needle plate, the<br />
tensioning plates must be open. If<br />
they are not, loosen nut A and<br />
move arm B as necessary. To<br />
adjust the pressure applied by the<br />
presser-foot, screw or unscrew<br />
knob D as required.<br />
(770)963-7369 FAX(770)963-7641 2<strong>211</strong>ES<br />
Ajustes Sugeridos Para<br />
Rimoldi<br />
1. Posicion De Las Agujas (Dib. 1)<br />
La máquina ha sido calibrada con<br />
agujas RIM. Las agujas están en<br />
la posición correcta en el plano<br />
horizontal cuando, con sus puntas<br />
insertadas en la plancha de la<br />
aguja, están centradas con el<br />
ojete. Las agujas están en la<br />
posición correcta en el plano<br />
vertical cuando la distancia “a”<br />
entre la punta de la aguja en su<br />
posición más alta y el plano de la<br />
plancha de la aguja es como se<br />
muestra en el cuadro de fases<br />
que viene con el cabezal. Para<br />
ajustar, afloje el tornillo A en la<br />
prensa B y ajuste. Después<br />
apriete los tornillos de la prensa,<br />
asegurandose que es empotrada<br />
en su lugar contra la barra de la<br />
aguja. Ajuste la clavija C de<br />
forma que toca la prensa de<br />
sujeción de la aguja y entonces<br />
asegurela con el tornillo E.<br />
Apriete el tornillo A de la prensa.<br />
La distancia “a” en la máquina<br />
tiene que medirse desde la aguja<br />
de la derecha. Apriete el tornillo<br />
de la prensa. La distancia “a”<br />
tiene que caer entre la punta de la<br />
aguja de la derecha y la superficie<br />
del plancha de la aguja.<br />
2. Posición Del Prensatelas Y<br />
Graduación Del Resorte<br />
Regulador Del Prensatelas (Fig.2)<br />
El prensatela está en la posición<br />
correcta cuando las agujas pasan<br />
por el centro de las ranuras en el<br />
prensatelas. Las agujas pueden<br />
ser centradas aflojando el tornillo<br />
C el cual bloquea el prensatelas<br />
en la barra. Recuerde que con el<br />
prensatelas levantado acerca de<br />
4.5 mm sobre la plancha de la<br />
aguja, los platos tensionadores<br />
tienen que estar abiertos. Si no<br />
están, afloje la tuerca Aymueva<br />
el brazo B cuanto sea necesario.<br />
Para ajustar la presión aplicada<br />
por el prensatelas, atornille o<br />
desatornille la perilla D.<br />
2<strong>211</strong>ES ATLANTA ATTACHMENT COMPANY 2-11<br />
401 Industrial Park Dr.-Lawrenceville, GA. 30045