Le Courageux - CMC-Versand

Le Courageux
11.28 Spade plug --- 6.3 2 P.S.
11.29 Distributor --- 6.3 3 P.S.
11.30 Spade socket --- 6.3 5 P.S.
11.31 AMP socket --- --- 2 Multi-part, P.S.
11.32 Cable, red / black --- 1.5 mm² --- P.S.
11.33 Sound module --- --- 1 N.I.
11.34 Bass loudspeaker --- --- 1 N.I.
“FL” Spade socket for loudspeaker --- 2.8 / 4.8 2 FS
11.35 Self-tapping screw Steel 2.9 Ø x 6.5 4 FS
11.36 Multi-Switch decoder 16 --- --- 1 N.I.
11.37 10-pin connector --- --- 1 FS
11.38 Servo lead for decoder --- --- 7 N.I.
Fig. 258
- The component parts of the rudder system.
- Gradually drill out the rudder 11.3 from the underside to a
depth of 20 mm, finishing with a bore of 3 mm Ø. The hole
must be exactly in line with the rudder shaft axis.
Fig. 259
- Screw the propeller 11.1 onto the propeller shaft 2.9 and
lock it against the nut 1.8.
- Slide the spacer sleeve 11.2 onto the shaft of the rudder
11.3. Grease the rudder shaft lightly.
- Insert the rudder into the rudder bush from the underside.
- Cut a piece about 50 mm long from the jig wire “HD” to
form the bottom rudder shaft 11.4; fit this in the rudder
from the underside, slipping the collet 11.5 onto it at the
same time.
- Check that the rudder swivels freely, then tighten the
grubscrew in the collet 11.5.
- Mark the projecting end of the bottom rudder shaft 11.4,
and cut it off at that point.
Fig. 260
- Fit the O-ring 11.6 and the washer 11.7 on the rudder
shaft.
- Slip the collet 11.9 and the socket-head screw 11.10 on
the tiller, and fit it on the top end of the rudder shaft.
- Connect the rudder pushrod 11.11 to the tiller as shown.
- Set the rudder to the “straight ahead” position. Align the
tiller at right-angles to the rudder, then tighten the sockethead
screw 11.10.
Fig. 261
- The component parts of the rudder servo.
Fig. 262
- Install the plastic servo mount 11.12 in the hull in the position
shown.
Fig. 263
Assembly and operating instructions
- Set the rudder servo 11.13 to centre (neutral) from the
transmitter. Connect the rudder pushrod 11.14 to the output
disc of the rudder servo.
- Install the servo, and connect the two pushrods using the
collet 11.15 and the socket-head screw 11.16.
- Check again that the rudder is at centre, then tighten the
screw 11.16.
26
Figs. 264 and 265
No.
1025
Notes: the wiring should be carried out in accordance with
the wiring diagram (see plan).
During the next stage, when you are wiring the various electronic
components, be sure to read the instructions supplied
with each device.
It is up to the builder to make up the individual connecting
leads required.
Servo extension leads may be needed in order to connect
particular electronic components to the receiver.
Basic functions
- Install the switch harness 11.17.
- Unwind the flexible wire aerial attached to the receiver.
Secure the receiver 11.18 and the receiver battery 11.19
using Velcro (hook-and-loop) tape. Connect the receiver
battery to the receiver using the switch harness.
- Deploy the receiver aerial below the deck.
- Withdraw the red wire from the receiver connector attached
to the speed controller 11.20 and insulate the bare
end, as the BEC system is not required - see the close-up
sketch.
- Connect the rudder servo and the speed controller to the
receiver.
- Check that the rudder system works correctly.