Le Courageux - CMC-Versand

More documents

Recommendations

Info

Stage 12, rigging, final work Assembly and operating instructions Le Courageux Part Description Material Size in mm No. Notes No. off 12.1 Turnbuckle Plastic Ready made 2 12.2 Countersunk screw Steel 2.2 Ø x 6.5 2 12.3 Pulley block Plastic Ready made 6 FS 12.4 Lashing Thread 0.7 Ø, overlength 2 FS 12.5 Flag halyard Thread 0.5 Ø, overlength 1 FS 12.6 Flag Fabric Ready made 1 FS 12.7 Aerial Flexible cable 0.3 Ø, overlength 1 FS 12.8 Power cable, front mast - superstr. Flexible cable 0.3 Ø, overlength 1 FS 12.9 Power cable, rear mast - superstr. Flexible cable 0.3 Ø, overlength 1 FS 12.10 S-hook Brass Ready made 2 FS 12.11 Solder sleeve Brass 1.5 Ø x 1 x 8 10 FS 12.12 Boom rigging Thread 0.7 Ø, overlength 4 FS 12.13 Block Wood Ready made 8 FS 12.14 Split pin Brass 1 x 15 4 FS 12.15 Ring-pin Brass Ready made 8 FS 12.16 Block and tackle halyard Thread 0.7 Ø x 1000 4 FS 12.17 Boathook tip Brass wire 1 Ø, as drawing 1 12.18 Boathook Brass wire 1 Ø, as drawing 1 12.19 Boathook handle Beech 2 Ø x 130 1 12.20 Scraper ABS 1, machine-cut 1 12.21 Scraper handle Beech 2 Ø x 90 1 12.22 Scraper brace Beech 2 Ø x 15 2 “K1” Template for keep-net Paper --- 1 12.23 Keep-net Fabric As template 1 FS 12.24 Keep-net frame Brass wire 1 Ø, as drawing 1 12.25 Keep-net handle Beech 2 Ø x 135 1 12.26 Lifebelt Plastic Ready made 1 FS 12.27 Name placard, front left ABS 1, machine-cut 1 12.28 Name placard, front right ABS 1, machine-cut 1 12.29 Name placard, upper stern ABS 1, machine-cut 1 12.30 Name placard, lower stern ABS 1, machine-cut 1 12.31 Rubbing strake ABS section 2 x 2, overlength 2 12.32 Name placard, wheelhouse ABS 1, machine-cut 1 12.33 Mooring rope Thread 1 Ø x 300 1 FS 12.34 Mast rigging Flexible cable 0.3 Ø, overlength 1 FS 12.35 Solder sleeve Brass 1.5 Ø x 1 x 8 2 FS 28 No. 1025
Overall view of the rigging The rigging is installed in the following groups: Parts 12.3 - 12.11 Aerial and power cables 12.12 Rigging to the derricks 12.13 - 12.16 Block and tackles to the gallows The sketch below shows the method of securing wire ends using a brass sleeve. An S-hook can be fitted at the same time where required. Fig. 278 - Mark the position of the turnbuckles 12.1, drill 1.5 mm Ø holes at the appropriate points and install the turnbuckles using the countersunk screws 12.2. The turnbuckles are used to secure the rear hatch. Figs. 279 - 281 - Attach a small pulley block 12.3 to the upper yard of the rear mast, and another to the superstructure railing, using thread lashings 12.4. - Attach the flag 12.6 to the flag halyard, and run it through the blocks. Tie a knot in the halyard close to the flag. Figs. 282 - 285 - Fix four small pulley blocks 12.3 to the upper yards using thread. - Deploy the aerial 12.7 and the front power cable 12.8, starting at the forward mast base. Route the aerial to the rear mast base in order to determine the correct length. Le Courageux - Provide a separation point between the front and rear masts using an S-hook 12.10 and two sleeves 12.11 as shown, so that the wheelhouse can be removed when necessary. - Route the rear power cable 12.9 from the rear mast base through the pulley block 12.3 to the rear split pin 5.53 in the wheelhouse roof. Figs. 286 and 287 - Install another separation point in the front power wire 12.8, and route it to the front split pin 5.53 on the wheelhouse. Figs. 288 and 289 - Place the aerial and the power wires under light tension, thread them through the split pins 8.26 and 8.8, and secure them using the brass sleeves 12.11. Figs. 290 and 291 - Run the boom rigging 12.12 from the split pins on the gallows 9.20 to the split pins 8.6 and 8.24 on the derricks, and tie them at those points. Fig. 292 Assembly and operating instructions - Drill out the cross-holes in the blocks 12.13 to 1 mm Ø. - Shorten the split pins 12.14 as shown, and connect them to the lower yards of the rear masts. - Drill 1 mm Ø holes in the top and bottom of the blocks, and glue the ring-pins 12.15 in the bottom; note that the pin shanks must end short of the cross-holes. - Cut four block and tackle halyards 12.16 to a length of 1000 mm, and make up the tackles using the blocks, as shown in the photo. 29 Fig. 293 No. 1025 - Glue the split pins 12.14 in the upper blocks. - Route the tackles from the lower mast yard to the gallows, and connect them to the rear split pin 9.20. - Belay the loose end of each tackle to the cleats 8.9 on the mast. Fig. 294 - Attach the front tackles as described for the rear ones. - Belay the bottom end of the tackles to the cleats 8.27 on the front mast. Fig. 295 - Assemble the boathook tip from the pieces of brass wire 12.17 and 12.18, as shown in the full-size drawing. Cut the wooden boathook handle 12.19 to length, drill a hole at the top and glue the prepared boathook tip in it. Fig. 296 - Make the scraper from parts 12.20 - 12.22. Fig. 297 - Cut the keep-net 12.23 to the shape of the template “K1”, form it into a conical shape, and sew the seams. - Bend the keep-net frame 12.24 to the shape shown in the full-size drawing, thread the keep-net onto it, and tie it in place using thread. - Tie the wooden keep-net handle 12.25 to the keep-net frame using thread.
Page 1 and 2: Assembly and operating instructions
Page 3 and 4: finally screwed or glued to the mod
Page 5 and 6: Stage 1, the hull Fig. 1 - The boat
Page 7 and 8: Le Courageux Part Description Mater
Page 9 and 10: Fig. 54 - Place the girders 3.3 in
Page 11 and 12: paint the strips before installing
Page 13 and 14: Fig. 128 - Attach the wheelhouse wa
Page 15 and 16: Figs. 131 and 132 - Locate the uppe
Page 17 and 18: Stage 6, the winch Assembly and ope
Page 19 and 20: Stage 7, fitting out the deck Le Co
Page 21 and 22: Note: shorten the split pins as req
Page 23 and 24: Fig. 213 - The component parts of t
Page 25 and 26: Figs. 241 and 242 - The next step i
Page 27: The overall electrical system consi
Page 31 and 32: Caractéristiques techniques longue
Page 33 and 34: Stade de montage 0, berceau Le Cour
Page 35 and 36: Fig. 23 - Couple de l’ensemble de
Page 37 and 38: Stade de montage 3, le pont Le Cour
Page 39 and 40: naux. L’écoutille est verrouill
Page 41 and 42: Stade de montage 4, le poste de pil
Page 43 and 44: Notice de montage et de pilotage Le
Page 45 and 46: Fig. 150 - Préparer les feux de po
Page 47 and 48: Fig. 167 - Pour réaliser le palier
Page 49 and 50: Fig. 194 - raccourcir par poussée
Page 51 and 52: Stade de montage 9, les potences Le
Page 53 and 54: Stade de montage 10, panneaux de ch
Page 55 and 56: Le Courageux 11.29 distributeur ---
Page 57 and 58: Stade de montage 12, haubanage et t
Page 59 and 60: Fig. 298 - Fixer la gaffe, le pouss
Page 61 and 62: Occorre infatti prima adattare il s
Page 63 and 64: Fase di costruzione 1, Lo scafo Imm
Page 65 and 66: Le Courageux Nr.Pezzo Descrizione M
Page 67 and 68: Immagine 54 - Inserire i profili 3.
Page 69 and 70: - Adattare ed incollare alternativa
Page 71 and 72: Immagine 128 - Posizionare le paret
Page 73 and 74: Immagini 131 e 132 - Infilare dall
Page 75 and 76: Fase di costruzione 6, gli argani I
Page 77 and 78: Fase di costruzione 7, l’allestim
Page 79 and 80:
Suggerimento: Qualora si renda nece
Page 81 and 82:
Immagine 213 - Rappresentazione del
Page 83 and 84:
imento la linea tratteggiata sulla
Page 85 and 86:
- 12 V (Alimentazione batteria del
Page 87 and 88:
Visione d’insieme dell’imbarcaz
Page 89 and 90:
Características Técnicas: Manga t
Page 91 and 92:
Fase de construcción 0, peana Le C
Page 93 and 94:
Foto 23 - Cuaderna RC 1.8, cuaderna
Page 95 and 96:
Fase de construcción 3, la cubiert
Page 97 and 98:
deben estar desplazados. Los soport
Page 99 and 100:
Fase de construcción 4, la caseta
Page 101 and 102:
Instrucciones de montaje y manejo L
Page 103 and 104:
- Encolar el cuerpo de luces 5.43.
Page 105 and 106:
Foto 167 - Para realizar los cojine
Page 107 and 108:
Foto 193 - Enhebrar los soportes de
Page 109 and 110:
Fase de construcción 9, la grúa L
Page 111 and 112:
Fase de construcción 10, Soportes
Page 113 and 114:
Le Courageux Nº Nomencl. Descripci
Page 115 and 116:
Fase de construcción 12, arriostra
Page 117 and 118:
Foto 299 - Poner las letras 12.26 e
Page 119 and 120:
119
show all

Le Courageux - CMC-Versand

Create successful ePaper yourself

Delete template?

Save as template?