Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Fig. 23<br />
- The RC bulkhead 1.18, the loudspeaker bulkhead 1.19<br />
and the RC plate 1.20.<br />
Fig. 24<br />
- Place the RC bulkhead 1.18 and the speaker bulkhead<br />
1.19 in the hull as shown.<br />
Fig. 25<br />
- Place the RC plate 1.20 in position, as shown in the<br />
photo.<br />
Fig. 26<br />
- Adjust the position of all the bulkheads so that they fit<br />
snugly against each other. Check that they are all at rightangles<br />
to the hull centreline.<br />
- Tack the bulkheads to the hull using cyano; don’t glue the<br />
RC plate at this stage.<br />
Fig. 27<br />
- The component parts of the forecastle deck bulkhead.<br />
Stage 2, the power system<br />
Fig. 28<br />
<strong>Le</strong> <strong>Courageux</strong><br />
- Glue the half-bulkhead 1.21, the deck support 1.22 and<br />
the forecastle deck bulkhead 1.23 together, taking care to<br />
keep the edges flush.<br />
Figs. 29 and 30<br />
- Place the forecastle deck bulkhead 1.21 - 1.23 and the<br />
bow bulkhead 1.24 in the hull, position them carefully and<br />
fix them in place with cyano.<br />
Figs. 31 and 32<br />
- Remove the RC plate 1.20. Apply a thin fillet of Stabilit-<br />
Express to all the joints between the bulkheads and the<br />
hull.<br />
- The RC bulkhead 1.18 can now be glued in place permanently.<br />
Fig. 33<br />
- The RC plate 1.20 can now be glued in place permanently.<br />
Fig. 34<br />
Assembly and operating instructions<br />
- The rear keel section doublers 1.25 (rudder spigot).<br />
6<br />
Figs. 35 and 36<br />
No.<br />
1025<br />
- Glue the doublers to the rear projecting part of the keel<br />
one by one, clamping them in place as shown.<br />
- Allow the glue to set hard, then clean up any excess<br />
adhesive.<br />
Figs. 37 and 38<br />
Part Description Material Size in mm No. Notes<br />
No. off<br />
2.1 Electric motor --- Ready made 1 P.S.<br />
2.2 Suppressor set --- 1 x 47 nF, 2 x 100 nF 1 P.S.<br />
2.3 Motor leads --- 1 x red, 1 x black 2 P.S.<br />
2.4 AMP plug --- Ready made 2 P.S.<br />
2.5 Insulator Plastic Ready made 1 P.S.<br />
2.6 Socket-head screw Steel M4 x 10 2 P.S.<br />
2.7 Washer Steel 4.3 I.D. 2 P.S.<br />
- Drill the hole for the stern tube, working from the rear,<br />
starting with a 3 mm Ø bit. Use progressively larger drills<br />
until the hole is 7 mm Ø. Clamp the 7 mm Ø bit in the<br />
chuck in such a way that the hole can be continued<br />
through the support bulkhead 1.12.<br />
Fig. 39<br />
- Drill a 4 mm Ø hole in the rear keel section to accept the<br />
top rudder bush.<br />
Fig. 40<br />
- Drill a 4 mm Ø hole in the projecting keel section to accept<br />
the bottom rudder bush.