Lieferprogramm | product range - WMH Herion
Lieferprogramm | product range - WMH Herion
Lieferprogramm | product range - WMH Herion
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
Profilschienenführung - Allgemeine Informationen<br />
Linear Guideway - General Information<br />
Standardöl:<br />
Mobil SHC 636, vollsynthetisch auf Hydrocarbon-Basis (PAO)<br />
Viskositätsklasse: ISO VG 680<br />
Ersatzweise können Öle gleicher Klassifikation und Viskosität<br />
verwendet werden.<br />
Die Austauschintervalle sind sehr stark von den Lasten und den Umgebungsbedingungen<br />
abhängig. Umgebungseinflüsse wie hohe Lasten,<br />
Vibrationen und Schmutz verkürzen die Austauschintervalle.<br />
Die folgende Tabelle gibt an, wann der Füllstand des Öltanks spätestens<br />
überprüft werden soll.<br />
Angesetzte Profilschienen<br />
Angesetzte Profilschienenführungen müssen gemäß dem Pfeil und<br />
der laufenden Nummer montiert werden, die auf der Oberfläche jeder<br />
Profilschiene angebracht sind. Bei paarweise montierten Profilschienen<br />
sollten die Stoßfugen versetzt werden (siehe Bild unten).<br />
Standard oil:<br />
Mobil SHC 636, full synthetic, based on hydrocarbon (PAO)<br />
Viscosity class: ISO VG 680<br />
Substed, oils of the same classification and viscosity can be used.<br />
The exchange intervals strongly depend on the loads and environmental<br />
conditions. Environmental influences like high loads, vibrations and dirt<br />
shorten the exchange intervals. The following table shows, until the fill<br />
level of the oil tank at last should be checked.<br />
Tabelle: Schmiermittelmengen Table: Lubrication quantities<br />
Modell |<br />
model<br />
Ölmenge |<br />
oil quantity [cm³]<br />
Jointed rail<br />
Laufleistung |<br />
running distance [km]<br />
HG15E2 1,6 1000<br />
HG20E2 3,9 2000<br />
HG25E2 5,1 3000<br />
HG30E2 7,3 4000<br />
HG35E2 9,8 5000<br />
HG45E2 18,5 10000<br />
HG55E2 25,9 15000<br />
HG65E2 50,8 25000<br />
EG15E2 1,7 1000<br />
EG20E2 2,9 1500<br />
EG25E2 4,8 2500<br />
EG30E2 8,9 4500<br />
1 Öltank | oil tank<br />
2 Schmiereinheit | lubrication unit<br />
3 Anschlussstück | connecting piece<br />
4 Schraube | screw<br />
5 Abschlussdichtung | closing seal<br />
6 Verschlussschraube | screw plug<br />
7 Umlenksystem | reversing system<br />
Jointed rail should be installed by following the arrow sign and ordinal<br />
number which is marked on the surface of each rail. For matched pair,<br />
jointed rail, the jointed positions should be staggered. This will avoid accuracy<br />
problems due to discrepancies between the 2 rails (see figure).<br />
A 12