OPERATOR'S MANUAL BIOPROtect II JR Vent to ... - Baker Company

More documents

Recommendations

Info

The BIOPROtect II JR incorporates a solid-state ‘Stedivolt’ controller to adjust the blower motor speed. This unit compensates for some variation in incoming line voltage. The usable voltage range is 95 to 130V AC. You will need to consult the most recent certification test report on the unit to determine what the voltage setting should be for your unit. Environmental Conditions The BIOPROtect JR is designed to be used under the following conditions: Indoor use Altitudes up to 2000 meters Temperature range from 5° C to 40° C Relative humidity up to 80% Main supply voltage 105 to 125 VAC Maximum relative humidity 80 percent for temperatures up to 31°C decreasing linearly to 50 percent relative humidity at 40°C. Transient over voltages according to Installation Category(OVERVOLTAGE CATEGORIES) II per UL 61010A-1, Annex J. Pollution Degree 2 Symbols and Terminology ! Protective Earth: Any terminal which is intended for connection to an external protective conductor for protection against electric shock in case of a fault. General Caution: Refer to the instruction manual for information regarding personnel and environment protection.) http://solid/prereleased/prereleased/STAN. PRODUCT/313/DOCS/313D000.doc Page 5 of 59
The Uses of the BIOPROtect II Jr. II - PREPARING THE BIOPROtect II JR CABINET FOR USE The BIOPROtect II JR cabinet has been designed to provide a work area that protects the experiment from the environment (Product protection), and protects the users from the experiment (personnel protection or ‘containment’). The laminar flow biological safety cabinet is designed for work with Biosafety Levels 1, 2 and 3 (low to moderate risk) agents as listed in The Center for Disease Control’s “Biosafety in Microbiological and Biomedical Laboratories”, U.S. Department of Health and Human Services, Public Health Service, Centers for Disease Control and National Institutes of Health, U.S. Government Printing Office, Washington, D.C. 20402. HHS publication number (CDC) 84-8395. Extremely high risk agents assigned to Biosafety level 4 should never be used in this cabinet except in a certified BSL4 suit room. Please consult your safety professional for a proper risk assessment. Cautions * The use of any hazardous material in the cabinet requires that it be monitored by an industrial hygienist, safety officer or other qualified individual. * Explosive or flammable substances should never be used in the cabinet unless a qualified safety professional has evaluated the risk. * If hazardous biological work is to be performed, apply the appropriate biohazard decal which is enclosed. This is in accord with OSHA regulations, volume 39, number 125, Part II. * If chemical, radiological or other non-microbiological hazards are present, be sure to employ appropriate protective measures in addition to formaldehyde decontamination.Also see section 2 “Decon”. Call upon a suitably trained individual to monitor the operation. Location Within the Laboratory PROPER PLACEMENT WITHIN THE LABORATORY IS ESSENTIAL. The ideal location for any laminar flow biological safety cabinet is in a dead-end corner of the laboratory away from personnel traffic, vents, doors, windows or any other sources of disruptive air currents. Published research from The Baker Company (see Rake ASM paper, reference #34 in Appendix) and unpublished tests performed at the National Cancer Institute show that if a draft or other disruptive air current were to exceed the intake velocity of the cabinet, then contamination can enter the work area or escape from it. http://solid/prereleased/prereleased/STAN. PRODUCT/313/DOCS/313D000.doc Page 6 of 59
Page 1 and 2: OPERATOR’S MANUAL BIOPROtect II J
Page 3 and 4: Table of Contents INTRODUCTION AND
Page 5 and 6: BGA-BIOPROTECT II-JR Canopy Exhaust
Page 7 and 8: Access to the Work Area Figure 1 Ty
Page 9: Specifications Dimensions: Outside:
Page 13 and 14: Ground Fault Circuit Interrupter Gr
Page 15 and 16: Set-up Procedure This section outli
Page 17 and 18: Reacting to Spills Caution: An Emer
Page 19 and 20: After 25% of the paraformaldehyde h
Page 21 and 22: IV - ON-SITE CHECKS AND MAINTENANCE
Page 23 and 24: The Airflow Balance Warning! This p
Page 25 and 26: Calibration procedure for Modus Air
Page 27 and 28: Maintenance Notes Replacing the HEP
Page 29 and 30: V. - TROUBLE SHOOTING Here are some
Page 31 and 32: REPLACEMENT PARTS LIST PART NAME QT
Page 33 and 34: Modus Installation and Operation Ha
Page 35 and 36: http://solid/prereleased/prerelease
Page 47 and 48: BGA-BIOPROTECT II-JR Vent to Room P
Page 49 and 50: BGA-BIOPROTECT II-JR Vent to Room P
Page 51 and 52: BGA-BIOPROTECT II-JR Canopy Exhaust
Page 53 and 54: BGA-BIOPROTECT II-JR Hard Exhaust C
Page 55 and 56: BGA-BIOPROTECT II-JR Hard Exhaust C
Page 57 and 58: Wiring Diagram-Standard BIOPROtect
Page 59: WARRANTY The Baker Company, Inc. ex

OPERATOR'S MANUAL BIOPROtect II JR Vent to ... - Baker Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?