Single Reduction & Single Reduction with Differential Lock - Spicer

More documents

Recommendations

Info

Disassemble and Overhaul Drive Pinion The following procedures cover both forward and rear differential drive carrier disassembly. Rear Axle Pinion Yoke 1. Remove yoke. If pinion nut was not loosened during earlier disassembly, clamp assembly in vise jaws, use brass pads to prevent damage. 15 2. Loosen and remove pinion nut and flat washer. Remove yoke from pinion using an appropriate tool. Forward and Rear Axle Pinion Bearing Cage 3. Press pinion out of bearing cage and bearing cone. 1 - Press Ram CAUTION Rear Axle Pinion Oil Seal and Outer Bearing Cone 1 4. Remove oil seal and bearing cone from cage. Discard oil seal. Remove bearing cups <strong>with</strong> suitable puller. Pinion Assembly 5. Remove bearing spacer from pinion. 6. Remove pilot bearing from pinion using a split-type puller. Use two procedure steps to remove each bearing. a. Mount puller vertically to separate the bearing. This action will force puller halves under bearing and start moving bearing off pinion. b. Mount puller horizontally to press pinion out of bearing. 7. Remove inner bearing cone from pinion using a split-type puller. Use two procedure steps to remove each bearing.
a. Mount puller vertically to separate the bearing. This action will force puller halves under bearing and start moving bearing off pinion. b. Mount puller horizontally to press pinion out of bearing. 1 1 - Press Pinion Assembly 16 Service Procedure
Page 1 and 2: Spicer ® Single Drive Axles Servic
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Introduction Dana presents this pub
Page 7 and 8: Ring Gear and Pinion General Inform
Page 9 and 10: Prepare the Parts for Inspection Af
Page 11 and 12: Differential Carrier Assembly - Par
Page 13 and 14: Install Differential Carrier Before
Page 15 and 16: Procedure - Remove Wheel Differenti
Page 17: Remove Pinion Assembly Procedure -
Page 21 and 22: Pinion Assembly Adjust Pinion Beari
Page 23 and 24: Pinion Assembly Adjust Pinion Beari
Page 25 and 26: Use the correctly sized spacer. Do
Page 27 and 28: Install Drive Pinion Assembly Proce
Page 29 and 30: Wheel Differential - Exploded View
Page 31 and 32: Wheel Differential Disassemble, Ove
Page 33 and 34: 7. Align punch marks and install pl
Page 35 and 36: Change Backlash Setting If you have
Page 37 and 38: Adjust Pinion Position If the gear
Page 39 and 40: Wheel Differential Locking Axles Co
Page 41 and 42: 5. Position shift fork and clutch a
Page 43 and 44: Wheel Differental lock Install and
Page 45 and 46: Install and Adjust Wheel Differenti
Page 47 and 48: Axle Housing Install New Axle Housi
Page 49 and 50: Inter Axle Speed Sensor Inter-Axle
Page 51 and 52: Install Inter-Axle Speed Sensor Exc
Page 53 and 54: Remove and Overhaul Wheel End Seal
Page 55 and 56: Three-piece Tang-type Lock Washer S
Page 57 and 58: Lubrication Information Note: For L
Page 59 and 60: Operate Wheel Differential Assembly
Page 61 and 62: Wheel Differential Lock Operation D
Page 63 and 64: Parts Identification Inter-Axle Spe
Page 65 and 66: Parts Identification Housing and Ou
Page 67 and 68: Note: In the previous charts, axle
Page 70:
For spec‘ing or service assistanc
show all

Single Reduction & Single Reduction with Differential Lock - Spicer

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?