John Deere AutoTrac™ Controller - StellarSupport - John Deere

More documents

Recommendations

Info

Deactivating System CAUTION: Always turn off (Deactivate and Disable) AutoTrac system before entering a roadway. To turn off AutoTrac from GUIDANCE VIEW tab, toggle STEER ON/OFF button until STEER OFF is displayed. AutoTrac system can be made DEACTIVE by following methods: • Turning steering wheel. StarFire AutoTrac controller takes its StarFire Height and Fore-Aft measurements from the StarFire setup. To change this information select the menu button then select the StarFire button. The StarFire main page will appear. Select the Setup tab (A) at the top of the screen. StarFire Height (in.) Enter the height of the StarFire receiver into the Height box (C) of the StarFire Setup screen. Height is measured from the ground to the center (where the green and yellow meet) of the dome. StarFire Fore-Aft (in.) Enter the Fore-Aft measurement into the Fore/Aft box (B) of the StarFire Setup screen. This is the distance from the fixed axle of the machine to the receiver. The fixed axle is the rear axle on a row crop tractor. The fixed axle is the front axle on an articulated tractor NOTE: For more information on StarFire setup see the StarFire operators manual that matches your equipment. A—Setup tab B—Fore/Aft C—Height GS3 Display 2630 25-2 • Slowing to speeds less than 0.5 km/h (0.3 mph). • Exceeding forward speed of Tractor - 30 km/h (18.6 mph) Sprayer - 37 km/h (23 mph) Combine - 20 km/h (12.4 mph) • Exceeding reverse speed of 10 km/h (6.0 mph). • Toggle STEER ON/OFF button until STEER OFF is displayed in GUIDANCE VIEW tab. • Operator out of seat for more than 5 seconds if using seat switch or no activity detected by operator presence monitor for 7 minutes. PC8663 —UN—05AUG05 PC13738 —UN—17MAY11 Menu Button SF3000 Button StarFire Setup Screen OUO6050,0000D68 -19-22SEP07-1/1 PC13726 —UN—19MAY11 BA31779,00003BD -19-21FEB12-1/1 031312 PN=28
AutoTrac Setup Operate Guidance Systems Safely Read and understand Operate Guidance Systems Safely in the Safety section. AutoTrac System General Information IMPORTANT: AutoTrac system relies on GPS system operated by the United States government, which is solely responsible for its accuracy and maintenance. System is subject to changes that could affect accuracy and performance of all GPS equipment. Operator must maintain responsibility for machine and must turn at end of each track. This system will not turn at end of a track unless equipped with iTEC Pro. AutoTrac basic system is intended to be used as an assistance tool to mechanical markers. Operator must evaluate overall system accuracy to determine specific field operations where assisted steering may be used. This evaluation is necessary because accuracy required for various field operations may differ depending on farming operation. Because AutoTrac uses STARFIRE differential correction network along with Global Positioning System (GPS), slight shifts in position may occur over time. AutoTrac Accuracy—The overall AutoTrac system accuracy is dependent upon many variables. The equation looks like: AutoTrac System Accuracy = Signal accuracy + Vehicle Setup + Implement Setup + Field/Soil Conditions. GS3 Display 2630 25-3 It is very important to remember: • Receiver has to go through a warm-up period after starting. • Vehicle is setup properly (ballasted according to vehicle operator manual, etc.) • Implement is setup to run properly (wear parts such as shanks, shovels, and sweeps are in good working condition and correctly spaced). • Understand how field/soil conditions affect system (loose soil requires more steering than firm soil, but firm soil can cause uneven draft loads). Status Pie IMPORTANT: Although AutoTrac system can be activated when SF2 (or SF1 if using AutoTrac SF1 activation) correction signal is confirmed, system accuracy may continue to increase after powering up system. AutoTrac SF2 activation will operate on SF1, SF2, or RTK signal. AutoTrac SF1 activation will operate on SF1 signal only. NOTE: The status pie and steer icon will not be displayed if no SSU or AutoTrac Activation is detected. AutoTrac icon has four stages as shown in the AutoTrac Status Pie • INSTALLED • CONFIGURED • ENABLED Continued on next page BA31779,00003B8 -19-29FEB12-1/22 031312 PN=29
Page 1 and 2: John Deere AutoTrac Controller *OMP
Page 3 and 4: Contents Page Safety Recognize Safe
Page 5 and 6: Recognize Safety Information This i
Page 7 and 8: Operate Guidance Systems Safely Do
Page 9 and 10: Automatic Guidance System Detected
Page 11 and 12: AutoTrac Controller Compatibility F
Page 13 and 14: Activity Monitor Operator Detection
Page 15 and 16: Wheel Angle Sensor Calibration Sele
Page 17 and 18: Turn wheel back to CENTER with whee
Page 19 and 20: Turn steering wheel back to center
Page 21 and 22: Necessary Conditions for Activating
Page 23 and 24: Diagnostic Readings A—View Drop-D
Page 25 and 26: John Deere AutoTrac Controller Trou
Page 27: Automatic Guidance System Detected
Page 31 and 32: Steering Sensitivity To adjust stee
Page 33 and 34: masking actual machine faults and w
Page 35 and 36: Step 2: Optimize Acquire Sensitivit
Page 37 and 38: Advanced AutoTrac Screens A—View
Page 39 and 40: Optimizing AutoTrac Controller Perf
Page 41 and 42: Steering Wheel Speed Adjusts the ra
Page 43 and 44: AutoTrac Detected CAUTION: AutoTrac
Page 45 and 46: Setup A—View tab B—Guidance Set
Page 47 and 48: Advanced AutoTrac SettingsThe accep
Page 49 and 50: Heading Lead Determines the impact
Page 51 and 52: Step 2: Optimize Acquire Sensitivit
Page 53 and 54: Troubleshooting GS2 Display 2600 Sy
Page 55 and 56: Troubleshooting—GS2 2600 and GS3
Page 57 and 58: Trouble Code Pop-Up Boxes—Guidanc
Page 59 and 60: Start-Up Screen Each time a machine
Page 61 and 62: Increase AutoTrac Steering Sensitiv
Page 63 and 64: Pan Map Left Pan Map Right Pan Map
Page 65 and 66: AutoTrac Status Pie The AutoTrac St
Page 67 and 68: StarFire AutoTrac controller takes
Page 69 and 70: AutoTrac Settings NOTE: AutoTrac Se
Page 71 and 72: Trouble Codes Troubleshooting—GS2
Page 73 and 74: Guidance Alarms Troubleshooting—G
Page 75 and 76: Diagnostic Addresses Diagnostic Add
Page 77 and 78: EC Declaration of Conformity Specif
Page 79 and 80:
A Index Page AccuGuide Isolation Va
Page 81 and 82:
Technical Information John Deere Se
Page 83 and 84:
John Deere Is At Your Service John
show all

John Deere AutoTrac™ Controller - StellarSupport - John Deere

Create successful ePaper yourself

Delete template?

Save as template?