John Deere AutoTrac™ Controller - StellarSupport - John Deere

More documents

Recommendations

Info

• ACTIVATED Stage 1 INSTALLED (1/4 of pie)—SSU and all other hardware necessary for use are installed. • SSU is detected Stage 2 CONFIGURED (2/4 of pie)—Tracking Mode has been determined. A valid Track 0 has been established. Correct StarFire signal level for AutoTrac activation is selected. Vehicle conditions met. • Guidance system has been turned ON in the display • Guidance Track 0 has been defined • AutoTrac Activation detected. • StarFire signal is present • SSU has no active faults pertaining to the steering function • Hydraulic oil warmer than minimum temperature Steer On/Off– Press the steer on/off button to move AutoTrac from the CONFIGURED stage to the ENABLED stage. Stage 3 ENABLED (3/4 of pie)—Steer Icon has been pressed. All conditions are met for AutoTrac to operate and system is ready to be activated. • Select Steer On/Off button once to turn “Steer On” Stage 4 ACTIVATED (4/4 of pie with “A”)—Resume switch has been pressed and AutoTrac is steering the vehicle. • Press Resume Switch—AutoTrac has been activated GS3 Display 2630 25-4 PC8832 —UN—25OCT05 PC8833 —UN—25OCT05 Stage 1—INSTALLED Stage 2—CONFIGURED BA31779,00003B8 -19-29FEB12-2/22 • Speed is less than maximum • TCM message is currently available and valid • In proper operating gear PC8836 —UN—25OCT05 PC8834 —UN—25OCT05 PC8835 —UN—25OCT05 Steer On/Off Stage 3—ENABLED Stage 4—ACTIVATED BA31779,00003B8 -19-29FEB12-3/22 BA31779,00003B8 -19-29FEB12-4/22 BA31779,00003B8 -19-29FEB12-5/22 Continued on next page BA31779,00003B8 -19-29FEB12-6/22 031312 PN=30
Steering Sensitivity To adjust steering sensitivity select the input box and enter the desired steering sensitivity value via numeric keypad and select the enter button. The sensitivity can also be adjusted up or down by selecting the + or – buttons on either side of the steer sensitivity input box. NOTE: Valid range for steer sensitivity is 50-200 with 200 being the most aggressive setting. User Adjustable Steering Sensitivity—steering sensitivity is aggressiveness of AutoTrac steering system. A high steering sensitivity setting is more aggressive to allow system to handle tough manual steering conditions Figure A GS3 Display 2630 PC8848 —UN—30OCT05 PC8852 —UN—30OCT05 Steer Sensitivity such as integral implements with a heavy draft load. A low steering sensitivity setting is less aggressive to allow system to handle lighter draft loads and higher speeds. Figure B A—Default Gain B—Entered Steering Gain C—Track D—2.5 seconds The steering sensitivity is only applied after machine is within 0.5 M (1.6 ft) of track FIGURE A. Therefore, adjusting steering sensitivity does not change line acquisition performance. The steering sensitivity is momentarily reduced if tractor front wheel and heading oscillations become too large. 25-5 BA31779,00003B8 -19-29FEB12-7/22 This event may be observed when implement is raised at start or end of row transitions. If this event is observed while implement is activated, sensitivity level is too high (see Steering Sensitivity). Continued on next page BA31779,00003B8 -19-29FEB12-8/22 PC8849 —UN—30OCT05 031312 PN=31
Page 1 and 2: John Deere AutoTrac Controller *OMP
Page 3 and 4: Contents Page Safety Recognize Safe
Page 5 and 6: Recognize Safety Information This i
Page 7 and 8: Operate Guidance Systems Safely Do
Page 9 and 10: Automatic Guidance System Detected
Page 11 and 12: AutoTrac Controller Compatibility F
Page 13 and 14: Activity Monitor Operator Detection
Page 15 and 16: Wheel Angle Sensor Calibration Sele
Page 17 and 18: Turn wheel back to CENTER with whee
Page 19 and 20: Turn steering wheel back to center
Page 21 and 22: Necessary Conditions for Activating
Page 23 and 24: Diagnostic Readings A—View Drop-D
Page 25 and 26: John Deere AutoTrac Controller Trou
Page 27 and 28: Automatic Guidance System Detected
Page 29: AutoTrac Setup Operate Guidance Sys
Page 33 and 34: masking actual machine faults and w
Page 35 and 36: Step 2: Optimize Acquire Sensitivit
Page 37 and 38: Advanced AutoTrac Screens A—View
Page 39 and 40: Optimizing AutoTrac Controller Perf
Page 41 and 42: Steering Wheel Speed Adjusts the ra
Page 43 and 44: AutoTrac Detected CAUTION: AutoTrac
Page 45 and 46: Setup A—View tab B—Guidance Set
Page 47 and 48: Advanced AutoTrac SettingsThe accep
Page 49 and 50: Heading Lead Determines the impact
Page 51 and 52: Step 2: Optimize Acquire Sensitivit
Page 53 and 54: Troubleshooting GS2 Display 2600 Sy
Page 55 and 56: Troubleshooting—GS2 2600 and GS3
Page 57 and 58: Trouble Code Pop-Up Boxes—Guidanc
Page 59 and 60: Start-Up Screen Each time a machine
Page 61 and 62: Increase AutoTrac Steering Sensitiv
Page 63 and 64: Pan Map Left Pan Map Right Pan Map
Page 65 and 66: AutoTrac Status Pie The AutoTrac St
Page 67 and 68: StarFire AutoTrac controller takes
Page 69 and 70: AutoTrac Settings NOTE: AutoTrac Se
Page 71 and 72: Trouble Codes Troubleshooting—GS2
Page 73 and 74: Guidance Alarms Troubleshooting—G
Page 75 and 76: Diagnostic Addresses Diagnostic Add
Page 77 and 78: EC Declaration of Conformity Specif
Page 79 and 80: A Index Page AccuGuide Isolation Va
Page 81 and 82:
Technical Information John Deere Se
Page 83 and 84:
John Deere Is At Your Service John
show all

John Deere AutoTrac™ Controller - StellarSupport - John Deere

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?