HS-105P, PE. SA AutoCam™ Pan & Tilt Head - Vinten Radamec

More documents

Recommendations

Info

HS-105P Installation Mechanical Installation For installations where the heads are frequently moved from location to location, a wedge plate and adapter may be used to attach the head to its mount - contact Vinten Inc. for more information. Contact Vinten for other mounting adapters if they are required for your installation. Mounting The Pan & Tilt Head Attach the HS-105P head to its mount using the three screws provided (1/4”-20) and tighten them securely Mounting And Balancing The Payload For proper operation it is very important that the load is properly balanced mechanically with the center of gravity set exactly on the tilt axis. 1. Start with the tilt cradle level. 2. Position the camera on the tilt cradle and attach with bolts through the tilt cradle into the base of the camera. Leave the bolts just loose enough to be able to slide the camera backwards and forwards. 3. Mount the lens on the camera (if it was not already installed). 4. Mount any other ancillary equipment such as tally lights etc. 5. Slide the camera back and forth until the overall payload feels balanced and is centered about the tilt axis of the head. Tighten the bolts in the base of the camera. 6. Check the balance after the bolts are tightened. If necessary, loosen the bolts that hold the camera to the cradle and carefully push the payload in the desired direction. Retighten the mounting bolts and check again for proper balance. It is best to move the payload in small increments even though this may require several steps until the balance is achieved. 7. Once the back and forth balance is achieved, proceed with adjustment of vertical balance. Tilt the camera approximately 30 degrees upward and release it. If the camera stays in the same position when released, the payload is properly balanced. 8. However, if the camera continues to move upwards after you let go, the payload is mounted too high. On the other hand, if the camera moves back towards the horizontal position when you let go, the payload is mounted too low. Determine if you need to raise or lower the tilt cradle. 9. Mark the position of the camera on the tilt cradle so it can be re-installed in the same position. Remove the camera from the tilt cradle. 10. Note or mark the vertical position of the tilt cradle to make sure that you move it in the desired direction. Loosen the two 1/4-20 hex head screws and raise or lower the cradle as necessary. Tighten the screws securely. 3-4 User Manual
HS-105P Installation 11. Remount the payload and repeat step 7 to check the balance. Move the tilt cradle again if necessary until balance is achieved. User Manual 3-5
Page 1 and 2: HS-105P, PE. SA AutoCam Pan & Tilt
Page 3 and 4: Critical Data For HS-105P Mass (Wei
Page 5 and 6: Warranty Vinten, Incorporated (Vint
Page 7 and 8: Table Of Contents HS-105P Pan & Til
Page 9 and 10: Table Of Contents Analog Servos 4-9
Page 11 and 12: 1 Safety & Introduction User Manual
Page 13 and 14: HS-105P Safety & Introduction If th
Page 15 and 16: HS-105P Safety & Introduction Manua
Page 17 and 18: HS-105P Safety & Introduction power
Page 19 and 20: HS-105P Safety & Introduction HS-10
Page 21 and 22: 2 Operation User Manual 2-1
Page 23 and 24: 3 Installation User Manual 3-1
Page 25: HS-105P Installation This page left
Page 29 and 30: HS-105P Installation Minimizing Bac
Page 31 and 32: HS-105P Installation This page left
Page 33 and 34: HS-105P Installation This page left
Page 35 and 36: HS-105P Installation 4. Plug the le
Page 37 and 38: HS-105P Installation 4. Use a 7/64
Page 39 and 40: HS-105P Installation 5. Use a 7/64
Page 41 and 42: HS-105P Installation 1. The normal
Page 43 and 44: HS-105P Installation J1 - Pan Clip
Page 45 and 46: HS-105P Installation J2 - Tilt Clip
Page 47 and 48: HS-105P Installation J3 - Miscellan
Page 49 and 50: HS-105P Installation Listening To T
Page 51 and 52: 4 Maintenance And Repair User Manua
Page 53 and 54: HS-105P Maintenance And Repair Safe
Page 55 and 56: HS-105P Maintenance And Repair Chec
Page 57 and 58: HS-105P Maintenance And Repair User
Page 59 and 60: HS-105P Maintenance And Repair Anal
Page 61 and 62: HS-105P Maintenance And Repair 3. T
Page 63 and 64: HS-105P Maintenance And Repair 2. N
Page 71 and 72: A ACP System 1-10 Analog Servos 4-9

HS-105P, PE. SA AutoCam™ Pan & Tilt Head - Vinten Radamec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?