Eaton E Series DX Product Manual - Fusion Power System

More documents

Recommendations

Info

1.3 CE marking The product has the CE marking in compliance with the following European directives: LVD Directive (Safety) 2006/95/EEC EMC Directive 2004/108/EEC The only user operations permitted are: Start up and shut down the UPS, excluding the commissioning start-up.Use of the LCD control panel and Emergency <strong>Power</strong> Off (EPO) switch.Use of optional connectivity modules and their software.The user must follow the precautions and only perform the described operations.Any deviations from the instructions could be dangerous to the user or cause accidental load loss. 2 Warning! The user is not permitted to open any screws excluding connectivity plates and the Emergency <strong>Power</strong> Off (EPO) switch. Failure to recognise the electrical hazards could prove fatal. Caution! Read the manual before operating or working on the UPS. Note! This product for commercial and industrial application in the second environment Instal- lation restrictions or additional Measures may be needed to prevent disturbances. 1.4 User precaution
1.5 Environment The UPS must be installed according to the recommendations in this manual.Under no circum- stances the UPS should be installed in an airtight room, in the presence of flammable gases, or in an environment exceeding the specification.Excessive amount of dust in the operating environment of UPS may cause damage or lead to malfunction. The UPS should be always protected from the outside weather and sunshine. The recommended operating temperature is from +15 to +20 Celsius degrees.The recommended operating humidity:20% to 90%. 1.6 Inquiries Address any inquiries about the UPS and battery cabinet(s) to the local office or agent authorized by the manufacturer. Please quote the type code and the serial number of the equipment. 3
Page 2 and 3: ©2008 Eaton Corporation All Rights
Page 4 and 5: 5. 6. 7. 8. 9. Electrical installat
Page 8 and 9: 2 Introduction The product describe
Page 10 and 11: ① AC: This light and inverter lig
Page 12 and 13: 8 Front view(door open) CHGR FAN Ma
Page 14 and 15: 3.4 Characteristics 3.5 AC input 10
Page 16 and 17: 4 Mechanical installation The UPS a
Page 18 and 19: 4.3 Planning before installation Th
Page 20 and 21: The switching sequence for circuit
Page 22 and 23: 1)Switch-off picture 2)If it is in
Page 24 and 25: Then the UPS turn to bypass mode. 4
Page 26 and 27: 5 Electrical installation 5.1 Elect
Page 28 and 29: 2.If UPS rectifier input and bypass
Page 30 and 31: Routing of communication cables or
Page 32 and 33: 28 Notice! The most common battery
Page 34 and 35: Recharging batteries Exchanging bat
Page 36 and 37: RS232 port RS485 port 32
Page 38 and 39: 7 User operations 7.1 Single machin
Page 40 and 41: 5)Press ▼ again to obtain the bel
Page 42 and 43: 3)Select “Yes, Confirm” to swit
Page 44 and 45: 5)Select “Yes, Confirm” to swit
Page 46 and 47: 9. Procedures of DC switch-on: 42 A
Page 48 and 49: Single machine wire connection draw
Page 50 and 51: 8.1 Regular service/intervals The U
Page 52 and 53: 48 Note! Parrallel wires should be
Page 54 and 55: 11 Warranty The product is warrante
Page 56:
Should any display or warning messa
show all

Eaton E Series DX Product Manual - Fusion Power System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?