2.5.2 - Force10 Networks

More documents

Recommendations

Info

Executing the interface vlan 2-4094 command (Global Config mode) either creates a VLAN or selects a previously created VLAN (or use [no] interface vlan 2-4094 to delete a VLAN) and then enters the Interface VLAN mode, where you have access to commands that configure the selected VLAN: • To add an interface to the VLAN, use either the tagged intf-range or untagged intf-range command. The full syntax is: • [no] tagged {intf-range [native] | port-channel port-channel-range} • [no] untagged {intf-range | port-channel port-channel-range} • To change a dynamically created VLAN (see Using GVRP on page 228) to a static VLAN (permanently configure): — makestatic (in Interface VLAN mode) • To [reset] assign a name to a VLAN (VLAN 1 is always named Default, while the default for other VLANs is a blank string.): — [no] name name (up to 32 alphanumeric characters) • To configure the interface link layer encapsulation type: — encapsulation • To configure IGMP Snooping parameters for the VLAN: — igmp • To configure IP parameters, there are many command families: — For ip routing, use ip address and ip vrrp. — Multicast: For IP multicast, use [no] ip mcast boundary. For IGMP, use [no] ip igmp, [no] ip igmp last-member-query-count, and others detailed in the IP Multicast Commands chapter in the SFTOS Command Reference. — IP OSPF commands, such as ip ospf and ip ospf areaid areaid, are detailed in the OSPF Commands chapter in the SFTOS Command Reference. — ip rip commands are detailed in the RIP Commands chapter in the SFTOS Command Reference. • To set the MTU (maximum transmission unit) size: — [no] mtu 576-1500 (default is 1500) — [no] ip mtu 68-1500 for an MTU value for IP protocol • To configure the protocols associated with particular group IDs: — protocol group groupid Configuration Task List for VLANs • Creating the VLAN and Adding Ports • Clearing/Resetting a VLAN on page 222 • Adding a LAG to a VLAN on page 223 • Creating a Routed VLAN on page 225 • Enabling Dynamic VLANs with GVRP on page 229 • Creating an IP Subnet-based VLAN on page 231 • Configuring a Private Edge VLAN (PVLAN) on page 232 • Configuring a Native VLAN on page 233 218 VLANs
For more VLAN configuration examples: • In the Getting Started chapter, see introduction to VLAN configuration, Creating VLANS on page 49. • For more information on VLAN routing in this guide, see the VLAN section in Chapter 17, VLAN Routing on page 270. Creating the VLAN and Adding Ports The following instructions are the basic configuration tasks for creating the VLAN and adding ports to it: Step Command Syntax Command Mode Usage 1 interface vlan 2-4094 Global Config Specify a new or existing VLAN by VLAN number. 2 [no] tagged unit/slot/ port 3 [no] untagged unit/slot/ port Note: Enable each port added to the VLAN. Interface VLAN To add tagged ports to the VLAN, specify a single port in unit/slot/port format to add to the selected VLAN, or specify a sequential port range as unit/ slot/port-unit/slot/port. Specify a non-sequential port range as unit/slot/ port,unit/slot/port,... Specify a LAG ID as an integer (List LAG IDs with show interface port-channel brief.) Interface VLAN To add untagged ports to the VLAN, specify either a port, port range, port channel, or port channel range, as described above. 4 name VLAN-name Interface VLAN (OPTIONAL) Name the VLAN. 5 show vlan id vlanid Privileged Exec Verify the configuration. SFTOS Configuration Guide, Version <strong>2.5.2</strong>.0 219
Page 1 and 2:
SFTOS Configuration Guide Version 2
Page 3 and 4:
SFTOS 2.5.2 adds: • A substantial
Page 5 and 6:
Contents New Features . . . . . . .
Page 7 and 8:
Chapter 3 Management . . . . . . .
Page 9 and 10:
Chapter 9 Spanning Tree . . . . . .
Page 11 and 12:
Configuring a Native VLAN . . . . .
Page 13 and 14:
List of Figures Figure 1 Using the
Page 15 and 16:
Figure 77 Using the show interface
Page 17 and 18:
Figure 158 Using the access-list Co
Page 19:
Figure 243 Configuring VLANs for OS
Page 22 and 23:
Audience This document is intended
Page 24 and 25:
Technical Support The iSupport Webs
Page 26 and 27:
26 About this Guide
Page 28 and 29:
— Flow Control at the MAC layer:
Page 30 and 31:
• HTML-based Management • HTTPS
Page 32 and 33:
(Force10 S50) #show port 1/0/2 Figu
Page 34 and 35:
34 SFTOS Features
Page 36 and 37:
Setting up a Management Connection
Page 38 and 39:
Step Task (continued) 5 Enter Line
Page 40 and 41:
Getting Help From the CLI The follo
Page 42 and 43:
Showing Network Settings Execute th
Page 44 and 45:
Displaying Statistics Privileged Ex
Page 46 and 47:
Force10 (Config)#users snmpv3 acces
Page 48 and 49:
Enabling Telnet to the Switch Acces
Page 50 and 51:
• Enabling Spanning Tree Protocol
Page 52 and 53:
The S-Series switch contains severa
Page 54 and 55:
Downloading a Software Image After
Page 56 and 57:
5. After the transfer is complete,
Page 58 and 59:
An alternative is to use the copy c
Page 60 and 61:
Note that the association of a part
Page 62 and 63:
After installing SFTOS 2.5.1 on the
Page 64 and 65:
When converting from a Routing imag
Page 66 and 67:
Saving the Startup Configuration to
Page 68 and 69:
Chapter 5, Stacking S-Series Switch
Page 70 and 71:
Uploading a Configuration Script to
Page 72 and 73:
Troubleshooting a Downloaded Script
Page 74 and 75:
Listing Configuration Scripts The s
Page 76 and 77:
Changing the Management VLAN from t
Page 78 and 79:
Setting the Host Name Prompt If you
Page 80 and 81:
Setting up SNMP Management Simple N
Page 82 and 83:
Commands to [disable] enable traps
Page 84 and 85:
RMON is an extension of SNMP, and r
Page 86 and 87:
Figure 47 RMON Event Thresholds Fig
Page 88 and 89:
The software clock runs only when t
Page 90 and 91:
Example #5: show sntp server Force1
Page 92 and 93:
• logging history. See Configurin
Page 94 and 95:
Interpreting system log messages Ta
Page 96 and 97:
Displaying the SNMP Trap Log The sh
Page 98 and 99:
Force10 #config Force10 (Config)#lo
Page 100 and 101:
100 System Logs
Page 102 and 103:
• The S50N, S50V, and S25P models
Page 104 and 105:
Management Unit Selection Algorithm
Page 106 and 107:
All of the forwarding protocols run
Page 108 and 109:
Use the member unit switchindex com
Page 110 and 111:
Setting Management Unit Preferences
Page 112 and 113:
Hardware Management Preference The
Page 114 and 115:
Notice, in Figure 67, that show swi
Page 116 and 117:
Using show Commands for Stacking In
Page 118 and 119:
The show stack command shows pretty
Page 120 and 121:
Table 3 Interfaces in the S-Series
Page 122 and 123:
Force10 #show interface 1/0/1 Ports
Page 124 and 125:
Use the show interface ethernet uni
Page 126 and 127:
Physical interfaces can become part
Page 128 and 129:
Enabling an Interface Ports are shu
Page 130 and 131:
The following table describes the e
Page 132 and 133:
If you connect powered devices to a
Page 134 and 135:
Bulk Configuration Bulk configurati
Page 136 and 137:
136 Configuring Interfaces
Page 138 and 139:
Table 6 describes the messages that
Page 140 and 141:
Verifying the DHCP Server Configura
Page 142 and 143:
Configuration Example — DHCP Serv
Page 144 and 145:
Step Command Syntax 2 authenticatio
Page 146 and 147:
Command Syntax Command Mode Purpose
Page 148 and 149:
Force10 #config Force10 (Config)# F
Page 150 and 151:
The scripts provided use OpenSSH (h
Page 152 and 153:
3. Use the show logging command to
Page 154 and 155:
Spanning Tree Protocol (STP, IEEE 8
Page 156 and 157:
Port States RSTP merges states from
Page 158 and 159:
MSTP CLI Management SFTOS supports
Page 160 and 161:
Enabling STP Use the following comm
Page 162 and 163:
The following commands influence wh
Page 164 and 165:
MSTP Configuration Example The foll
Page 166 and 167:
Use the show spanning-tree interfac
Page 168 and 169: Figure 119 displays the output from
Page 170 and 171: Figure 123 shows the output of the
Page 172 and 173: 172 Spanning Tree
Page 174 and 175: • Static configuration is used wh
Page 176 and 177: Link Aggregation Group (LAG) Comman
Page 178 and 179: Interface Config mode commands Note
Page 180 and 181: Basic LAG configuration example Thi
Page 182 and 183: Using the Interface Range mode If y
Page 184 and 185: Verify the status of the LAG as dyn
Page 186 and 187: • Edge device: An edge device han
Page 188 and 189: Deploying DiffServ The four basic s
Page 190 and 191: Creating a Policy-Map The second st
Page 192 and 193: Example (per interface): Force10 #c
Page 194 and 195: Force10 #show class-map Class Class
Page 196 and 197: Conform Secondary CoS—The action
Page 198 and 199: The following is sample output from
Page 200 and 201: VLAN 10: Finance Layer 3 Switch Por
Page 202 and 203: Configuring Differentiated Services
Page 204 and 205: 204 Quality of Service
Page 206 and 207: Note that the order of the rules is
Page 208 and 209: — show mac access-lists Force10 #
Page 210 and 211: Protecting the Management Interface
Page 212 and 213: • An ACL applied to loopback inte
Page 214 and 215: Use the show storm-control command
Page 216 and 217: A VLAN is a set of end stations and
Page 220 and 221: Example of creating a VLAN and assi
Page 222 and 223: 3. Create VLAN 4 on switch R3 and a
Page 224 and 225: Example of adding a LAG to a VLAN F
Page 226 and 227: Example of creating a routed VLAN o
Page 228 and 229: GARP Timers The following are GARP
Page 230 and 231: 1. Name switch R1, enable GVRP glob
Page 232 and 233: Configuring a Private Edge VLAN (PV
Page 234 and 235: Two commands can configure a native
Page 236 and 237: Figure 186 Validating a Tagged Inte
Page 238 and 239: . Force10 #show interface ethernet
Page 240 and 241: DVLAN configuration example The exa
Page 242 and 243: Configure switch R7: !---------Trun
Page 244 and 245: Using the show vlan id vlan-id comm
Page 246 and 247: set igmp maxresponse 1-3599 (typica
Page 248 and 249: Use the show ip igmp interface unit
Page 250 and 251: Port Mirroring Commands The followi
Page 252 and 253: Stopping the mirroring session and
Page 254 and 255: 254 Port Mirroring
Page 256 and 257: Enabling Routing The S-Series alway
Page 258 and 259: Port Routing Configuration Example
Page 260 and 261: IGMP Proxy Configuration The follow
Page 262 and 263: Verifying the configuration Verify
Page 264 and 265: RIP Configuration Example The confi
Page 266 and 267: Border Router Port 0/2 192.150.2.1
Page 268 and 269:
Configuring OSPF on an S-Series ope
Page 270 and 271:
VLAN Routing This section introduce
Page 272 and 273:
3. As above, enable routing on R2:
Page 274 and 275:
5. Execute the show ip ospf command
Page 276 and 277:
1. As done previously, create the V
Page 278 and 279:
3. Use the show vlan id, show ip in
Page 280 and 281:
Port 0/2 192.150.2.1/24 Virtual Rou
Page 282 and 283:
3. Configure the IP address and sub
Page 284 and 285:
Note: In SFTOS 2.3.1.9, these messa
Page 286 and 287:
In addition to issuing the show swi
Page 288 and 289:
Monitoring SFPs The four fiber port
Page 290 and 291:
packets can be routed by the hardwa
Page 292 and 293:
• What was the LED status? (If th
Page 294 and 295:
294 • GVRP — Dynamic VLAN Regis
Page 296 and 297:
296 QoS • RFC 2474 — Definition
Page 298 and 299:
MIBs 298 • RFC 2096: IP forwardin
Page 300 and 301:
300 Force 10 MIBs You can see this
Page 302 and 303:
302
Page 304 and 305:
configuration, restore to factory d
Page 306 and 307:
inlinepower threshold command 132 i
Page 308 and 309:
MIBs, supported industry 298 mirror
Page 310 and 311:
RFC 3768 279 RFC 768 28, 294 RFC 78
Page 312 and 313:
show stack-port command 103 show st
Page 314:
VoIP support 202 VRID 281 VRRP 279
show all

2.5.2 - Force10 Networks

Create successful ePaper yourself

Delete template?

Save as template?