2.5.2 - Force10 Networks

More documents

Recommendations

Info

Configuring OSPF on an S-Series operating as a border router The next diagram shows the same network segment with the S-Series operating as the border router in area 0.0.0.2. The example shows the commands used to configure the switch with OSPF enabled on port 0/2 for communication with the inter-area router in the OSPF backbone, and on ports 0/3 and 0/4 for communication with subnets within area 0.0.0.2. Port 0/2 192.150.2.1 Layer 3 Switch acting as a Border Router Port 0/2 192.150.2.2 Port 0/3 192.130.3.1 Port 0/4 192.64.4.1 Figure 236 OSPF Example Network Diagram: Border Router 1. Enable routing for the switch. Force10 #config Force10 (Config)#ip routing Inter-area Router Area 2 Port 0/2 192.150.2.2 Area 3 2. Enable routing and assign the IP for ports 0/2, 0/3, and 0/4. Force10 (Config)#interface 1/0/2 Force10 (Interface 1/0/2)#routing Force10 (Interface 1/0/2)#ip address 192.150.2.2 255.255.255.0 Force10 (Interface 1/0/2)#exit Force10 (Config)#interface 1/0/3 Force10 (Interface 1/0/3)#routing Force10 (Interface 1/0/3)#ip address 192.150.3.1 255.255.255.0 Force10 (Interface 1/0/3)#exit Force10 (Config)#interface 1/0/4 Force10 (Interface 1/0/4)#routing Force10 (Interface 1/0/4)#ip address 192.150.4.1 255.255.255.0 Force10 (Interface 1/0/4)#exit Border Router 268 Layer 3 Routing
3. Specify the router ID and enable OSPF for the switch. Set disable 1583compatibility to prevent the routing loop. Force10 (Config)#router ospf Force10 (Config router)#enable Force10 (Config router)#router-id 192.130.1.1 Force10 (Config router)#no 1583compatibility Force10 (Config router)#exit Force10 (Config)# 4. Enable OSPF for the ports and set the OSPF priority and cost for the ports. Force10 (Config)#interface 1/0/2 Force10 (Interface 1/0/2)#ip ospf Force10 (Interface 1/0/2)#ip ospf areaid 0.0.0.2 Force10 (Interface 1/0/2)#ip ospf priority 128 Force10 (Interface 1/0/2)#ip ospf cost 32 Force10 (Interface 1/0/2)#exit Force10 (Config)#interface 1/0/3 Force10 (Interface 1/0/3)#ip ospf Force10 (Interface 1/0/3)#ip ospf areaid 0.0.0.3 Force10 (Interface 1/0/3)#ip ospf priority 255 Force10 (Interface 1/0/3)#ip ospf cost 64 Force10 (Interface 1/0/3)#exit Force10 (Config)#interface 1/0/4 Force10 (Interface 1/0/4)#ip ospf Force10 (Interface 1/0/4)#ip ospf areaid 0.0.0.2 Force10 (Interface 1/0/4)#ip ospf priority 255 Force10 (Interface 1/0/4)#ip ospf cost 64 Force10 (Interface 1/0/4)#exit Force10 (Config)#exit Force10 #exit SFTOS Configuration Guide, Version 2.5.2.0 269
Page 1 and 2:
SFTOS Configuration Guide Version 2
Page 3 and 4:
SFTOS 2.5.2 adds: • A substantial
Page 5 and 6:
Contents New Features . . . . . . .
Page 7 and 8:
Chapter 3 Management . . . . . . .
Page 9 and 10:
Chapter 9 Spanning Tree . . . . . .
Page 11 and 12:
Configuring a Native VLAN . . . . .
Page 13 and 14:
List of Figures Figure 1 Using the
Page 15 and 16:
Figure 77 Using the show interface
Page 17 and 18:
Figure 158 Using the access-list Co
Page 19:
Figure 243 Configuring VLANs for OS
Page 22 and 23:
Audience This document is intended
Page 24 and 25:
Technical Support The iSupport Webs
Page 26 and 27:
26 About this Guide
Page 28 and 29:
— Flow Control at the MAC layer:
Page 30 and 31:
• HTML-based Management • HTTPS
Page 32 and 33:
(Force10 S50) #show port 1/0/2 Figu
Page 34 and 35:
34 SFTOS Features
Page 36 and 37:
Setting up a Management Connection
Page 38 and 39:
Step Task (continued) 5 Enter Line
Page 40 and 41:
Getting Help From the CLI The follo
Page 42 and 43:
Showing Network Settings Execute th
Page 44 and 45:
Displaying Statistics Privileged Ex
Page 46 and 47:
Force10 (Config)#users snmpv3 acces
Page 48 and 49:
Enabling Telnet to the Switch Acces
Page 50 and 51:
• Enabling Spanning Tree Protocol
Page 52 and 53:
The S-Series switch contains severa
Page 54 and 55:
Downloading a Software Image After
Page 56 and 57:
5. After the transfer is complete,
Page 58 and 59:
An alternative is to use the copy c
Page 60 and 61:
Note that the association of a part
Page 62 and 63:
After installing SFTOS 2.5.1 on the
Page 64 and 65:
When converting from a Routing imag
Page 66 and 67:
Saving the Startup Configuration to
Page 68 and 69:
Chapter 5, Stacking S-Series Switch
Page 70 and 71:
Uploading a Configuration Script to
Page 72 and 73:
Troubleshooting a Downloaded Script
Page 74 and 75:
Listing Configuration Scripts The s
Page 76 and 77:
Changing the Management VLAN from t
Page 78 and 79:
Setting the Host Name Prompt If you
Page 80 and 81:
Setting up SNMP Management Simple N
Page 82 and 83:
Commands to [disable] enable traps
Page 84 and 85:
RMON is an extension of SNMP, and r
Page 86 and 87:
Figure 47 RMON Event Thresholds Fig
Page 88 and 89:
The software clock runs only when t
Page 90 and 91:
Example #5: show sntp server Force1
Page 92 and 93:
• logging history. See Configurin
Page 94 and 95:
Interpreting system log messages Ta
Page 96 and 97:
Displaying the SNMP Trap Log The sh
Page 98 and 99:
Force10 #config Force10 (Config)#lo
Page 100 and 101:
100 System Logs
Page 102 and 103:
• The S50N, S50V, and S25P models
Page 104 and 105:
Management Unit Selection Algorithm
Page 106 and 107:
All of the forwarding protocols run
Page 108 and 109:
Use the member unit switchindex com
Page 110 and 111:
Setting Management Unit Preferences
Page 112 and 113:
Hardware Management Preference The
Page 114 and 115:
Notice, in Figure 67, that show swi
Page 116 and 117:
Using show Commands for Stacking In
Page 118 and 119:
The show stack command shows pretty
Page 120 and 121:
Table 3 Interfaces in the S-Series
Page 122 and 123:
Force10 #show interface 1/0/1 Ports
Page 124 and 125:
Use the show interface ethernet uni
Page 126 and 127:
Physical interfaces can become part
Page 128 and 129:
Enabling an Interface Ports are shu
Page 130 and 131:
The following table describes the e
Page 132 and 133:
If you connect powered devices to a
Page 134 and 135:
Bulk Configuration Bulk configurati
Page 136 and 137:
136 Configuring Interfaces
Page 138 and 139:
Table 6 describes the messages that
Page 140 and 141:
Verifying the DHCP Server Configura
Page 142 and 143:
Configuration Example — DHCP Serv
Page 144 and 145:
Step Command Syntax 2 authenticatio
Page 146 and 147:
Command Syntax Command Mode Purpose
Page 148 and 149:
Force10 #config Force10 (Config)# F
Page 150 and 151:
The scripts provided use OpenSSH (h
Page 152 and 153:
3. Use the show logging command to
Page 154 and 155:
Spanning Tree Protocol (STP, IEEE 8
Page 156 and 157:
Port States RSTP merges states from
Page 158 and 159:
MSTP CLI Management SFTOS supports
Page 160 and 161:
Enabling STP Use the following comm
Page 162 and 163:
The following commands influence wh
Page 164 and 165:
MSTP Configuration Example The foll
Page 166 and 167:
Use the show spanning-tree interfac
Page 168 and 169:
Figure 119 displays the output from
Page 170 and 171:
Figure 123 shows the output of the
Page 172 and 173:
172 Spanning Tree
Page 174 and 175:
• Static configuration is used wh
Page 176 and 177:
Link Aggregation Group (LAG) Comman
Page 178 and 179:
Interface Config mode commands Note
Page 180 and 181:
Basic LAG configuration example Thi
Page 182 and 183:
Using the Interface Range mode If y
Page 184 and 185:
Verify the status of the LAG as dyn
Page 186 and 187:
• Edge device: An edge device han
Page 188 and 189:
Deploying DiffServ The four basic s
Page 190 and 191:
Creating a Policy-Map The second st
Page 192 and 193:
Example (per interface): Force10 #c
Page 194 and 195:
Force10 #show class-map Class Class
Page 196 and 197:
Conform Secondary CoS—The action
Page 198 and 199:
The following is sample output from
Page 200 and 201:
VLAN 10: Finance Layer 3 Switch Por
Page 202 and 203:
Configuring Differentiated Services
Page 204 and 205:
204 Quality of Service
Page 206 and 207:
Note that the order of the rules is
Page 208 and 209:
— show mac access-lists Force10 #
Page 210 and 211:
Protecting the Management Interface
Page 212 and 213:
• An ACL applied to loopback inte
Page 214 and 215:
Use the show storm-control command
Page 216 and 217:
A VLAN is a set of end stations and
Page 218 and 219: Executing the interface vlan 2-4094
Page 220 and 221: Example of creating a VLAN and assi
Page 222 and 223: 3. Create VLAN 4 on switch R3 and a
Page 224 and 225: Example of adding a LAG to a VLAN F
Page 226 and 227: Example of creating a routed VLAN o
Page 228 and 229: GARP Timers The following are GARP
Page 230 and 231: 1. Name switch R1, enable GVRP glob
Page 232 and 233: Configuring a Private Edge VLAN (PV
Page 234 and 235: Two commands can configure a native
Page 236 and 237: Figure 186 Validating a Tagged Inte
Page 238 and 239: . Force10 #show interface ethernet
Page 240 and 241: DVLAN configuration example The exa
Page 242 and 243: Configure switch R7: !---------Trun
Page 244 and 245: Using the show vlan id vlan-id comm
Page 246 and 247: set igmp maxresponse 1-3599 (typica
Page 248 and 249: Use the show ip igmp interface unit
Page 250 and 251: Port Mirroring Commands The followi
Page 252 and 253: Stopping the mirroring session and
Page 254 and 255: 254 Port Mirroring
Page 256 and 257: Enabling Routing The S-Series alway
Page 258 and 259: Port Routing Configuration Example
Page 260 and 261: IGMP Proxy Configuration The follow
Page 262 and 263: Verifying the configuration Verify
Page 264 and 265: RIP Configuration Example The confi
Page 266 and 267: Border Router Port 0/2 192.150.2.1
Page 270 and 271: VLAN Routing This section introduce
Page 272 and 273: 3. As above, enable routing on R2:
Page 274 and 275: 5. Execute the show ip ospf command
Page 276 and 277: 1. As done previously, create the V
Page 278 and 279: 3. Use the show vlan id, show ip in
Page 280 and 281: Port 0/2 192.150.2.1/24 Virtual Rou
Page 282 and 283: 3. Configure the IP address and sub
Page 284 and 285: Note: In SFTOS 2.3.1.9, these messa
Page 286 and 287: In addition to issuing the show swi
Page 288 and 289: Monitoring SFPs The four fiber port
Page 290 and 291: packets can be routed by the hardwa
Page 292 and 293: • What was the LED status? (If th
Page 294 and 295: 294 • GVRP — Dynamic VLAN Regis
Page 296 and 297: 296 QoS • RFC 2474 — Definition
Page 298 and 299: MIBs 298 • RFC 2096: IP forwardin
Page 300 and 301: 300 Force 10 MIBs You can see this
Page 302 and 303: 302
Page 304 and 305: configuration, restore to factory d
Page 306 and 307: inlinepower threshold command 132 i
Page 308 and 309: MIBs, supported industry 298 mirror
Page 310 and 311: RFC 3768 279 RFC 768 28, 294 RFC 78
Page 312 and 313: show stack-port command 103 show st
Page 314: VoIP support 202 VRID 281 VRRP 279
show all

2.5.2 - Force10 Networks

Create successful ePaper yourself

Delete template?

Save as template?